Honeywell XNX User guide

XNXTM Universal Transmitter
Safety Manual
Revision 2
• Table of Contents
• SIL 2 Certificates
• Overview
• Safety Parameters
• Fault Diagnostic Time Interval
• Proof Test
• Proof Testing Procedure

XNX Universal Transmitter
2
Table of Contents
1 SIL 2 Certificates ...........................................................3
1.1 XNX Gas Detector Transmitter .............................3
2 Overview .........................................................................4
3 Safety Parameters .........................................................5
3.1 Interval of Proof Testing .......................................5
4 Fault Diagnostic Time Interval ......................................6
5 Proof Test .......................................................................6
5.1 Purpose of Proof Testing .....................................6
5.2 Expected Outcome of Proof Testing ...................6
5.3 Tolerance of Output Current Levels ....................6
6 Proof Testing Procedure ...............................................7
6.1 Checking................................................................7
6.1.1 Force mA Output ...............................................7
6.1.2 Zero Gas mA Output ..........................................7
6.1.3 Calibration Gas mA Output ..............................7
6.2 Adjusting ...............................................................7
6.2.1 Calibrate 4.0 mA and 20.0 mA ..........................7
6.2.2 Zero Gas Calibration and Span Calibration ....8
6.2.2.1 Zero Gas Calibration ...................................8
6.2.2.2 Span Calibration .........................................9
6.3 Verifying mA Settings .........................................10
6.4 Testing .................................................................11
6.4.1 Fault and Alarm State ......................................11
6.4.2 Gas Verification ................................................12

XNX Universal Transmitter
SIL 2 Certificates 3XNX Gas Detector Transmitter
1 SIL 2 Certificates
1.1 XNX Gas Detector Transmitter

XNX Universal Transmitter
Overview 4XNX Gas Detector Transmitter
2 Overview
IEC 61508 is a generic functional safety standard. Functional safety
is defined in this standard as “part of the overall safety relating to the
Equipment Under Control (EUC) and the EUC control system which
depends on the correct functioning of the E/E/PES1 safety related
systems, other technology safety-related systems, and external risk
reduction facilities.”
A system is considered to be functionally safe if the random and
systematic faults do not kill or injure humans, pollute the environment,
and do not result in the loss of equipment or production.
A systematic fault is defined as a failure with a definite cause. A random
fault can happen at any time and the cause is unclear. The terms fault
and failure can be used interchangeably.
A Safety Integrity Level-certified system can detect the majority of
safe and unsafe failures. XNX is SIL 2 capable per IEC 61508. XNX
is SIL 3 capable in a redundant system per IEC 61508. Table 1 and
Table 2 below outline a system’s safety integrity level in relation to its
average probability of failure to perform its design function on demand
and probability of dangerous failure per hour.
Table 1. Average Probability of Failure to Perform Its Design Function on Demand (Low Demand
System)
Safety Integrity
Level
Low demand mode of operation (Average probability of
failure to perform its design function on demand (PFD))
4≥ 10-5 to < 10-4
3≥ 10-4 to < 10-3
2≥ 10-3 to < 10-2
1≥ 10-2 to < 10-1
1 Electrical/electronic/programmable electronic systems
Table 2. Probability of a Dangerous Failure Per Hour (High Demand System)
Safety Integrity
Level
High demand or continuous mode of operation
(Probability of a dangerous failure per hour (PFH))
4≥ 10-9 to < 10-8
3≥ 10-8 to < 10-7
2≥ 10-7 to < 10-6
1≥ 10-6 to < 10-5
NOTE:
The XNX system is Type B. A Type B system uses controllers
or programmable logic per IEC 61508.
The XNX product consists of a main board, a personality board, and
a sensor. The information presented in this manual is based on the
combination of the main board and personality board.
XNX
main
board
IR Personality
board
EC Personality
board
IR sensor
mV sensor
EC sensor
XNX Transmitter Sensor
Note: Only one personality board per XNX main board
mV Personality
board
This manual outlines the proof test procedure, a required operation to
maintain the XNX’s functional safety under low demand applications.

XNX Universal Transmitter
Safety Parameters 5Interval of Proof Testing
3 Safety Parameters
The safety parameters listed below are a combination of the main
board and personality board. These numbers were provided by TUV
in report 968/EL 665.00/09 (personality boards) and report 968/EZ
319.02/09 (main board).
For safety parameters of the individual sensors, refer to the XNX Safety
Parameters For Sensors White Paper.
Table 3. Safety Parameters of the XNX Transmitter (mV)
SFF PFDavg PFH
95% 4.8 x 10-4 1.12 x 10-7
Table 4. Safety Parameters of the XNX Transmitter (ECC)
SFF PFDavg PFH
97% 2.5 x 10-4 5.7 x 10-8
Table 5. Safety Parameters of the XNX Transmitter (IR)
SFF PFDavg PFH
97% 2.7 x 10-4 6.2 x 10-8
SFF: Safe Failure Fraction. A percentage of safe failures as compared
to all failures.
PFDavg
2: Average probability of failure to perform its design function
on demand.
PFH: Probability of a dangerous failure per hour.
2 PFDavg is a 1-year normalized value
3.1 Interval of Proof Testing
If the XNX is used in high demand systems, a proof test is not required.
If the XNX is used in low demand systems (defined as 1 demand or
less per year) a proof test is required. Perform the proof test once a
year to comply with IEC 61508.
Section 6 Proof Testing Procedure outlines the actions that must be
completed for a proof test.

XNX Universal Transmitter
Fault Diagnostic Time Interval 6Purpose of Proof Testing
4 Fault Diagnostic Time Interval
XNX conducts approximately 30 diagnostics total on the main board
and personality board. These diagnostics occur at different time
intervals, with the longest interval at 24 hours. But when a fault is
detected, it is reported within 3 seconds. Refer to the XNX Technical
Manual for more information on diagnostics.
5 Proof Test
5.1 Purpose of Proof Testing
A proof test is a periodic test to detect failures in the system so that,
if necessary, the system can be restored to an “as new” condition or
as close as practical to this condition.
5.2 Expected Outcome of Proof Testing
The following features are checked and adjusted if required
• current output at different levels (4.0 mA and 20.0 mA)
• verifying zero gas and span gas calibration current output
• verifying current output of warnings and faults
• simulating warnings and faults
• validation of the current output of zero gas and/or span gas
calibration (required if the current output of zero gas and/or
span gas calibration had to be changed)
5.3 Tolerance of Output Current Levels
The tolerance for the output current levels is ± 0.1 mA.
Example: If the procedure requires the current output to be 4.0 mA,
the actual current reading at the controller end can range from 3.9 mA
to 4.1 mA.

XNX Universal Transmitter
Proof Testing Procedure 7Checking
6 Proof Testing Procedure
6.1 Checking
The purpose of checking is to ensure the mA output meets the
expected levels. If the current does not meet the expected levels, it
will have to be adjusted. If, after completing 6.1.1, 6.1.2, and 6.1.3, the
mA output does meet the expected levels, proceed to 6.3.
6.1.1 Force mA Output
1. Ensure the current can be measured at the controller end.
The current will be measured using the procedures outlined
in 6.1.1 to 6.1.3.
2. From the Main Menu, select the Test Menu ( ).
CAUTION
The mA output set in this menu will revert to the normal operating
values when exiting the Test Menu. For more information on setting
the mA output levels for normal operation, see mA Levels in the XNX
Technical Manual.
3. From the Test Menu, select Force mA Output ( ).
The New mA Output screen shows the existing mA output in
the left column. The user can adjust the output by changing
the value in the column on the right.
Figure 1. New mA Output Screen
4. Ensure the current at the controller end is 4.0 mA. If the current
is not 4.0 mA, refer to 6.2.1 to adjust the output.
5. Repeat steps #2-4 to check the output of 20.0 mA.
6.1.2 Zero Gas mA Output
The procedure for zero gas is not applicable to the ECC O2 sensor.
1. Apply zero gas to the sensor.
2. The current at the controller end should be 4.0 mA.
If the mA output is not at the expected level when applying
zero gas, perform a Zero Gas Calibration. Refer to 6.2.2 and
complete the procedure for a Zero Gas Calibration.
6.1.3 Calibration Gas mA Output
1. Apply calibration gas to the sensor.
2. The current measured at the controller end is related to the
percentage of gas applied.
Example: 100% of full gas concentration is equivalent to
20.0 mA. If 75% of the full scale gas concentration is applied,
the mA output should be 16.0 mA.
If the mA output is not at the expected level when applying
calibration gas, refer to 6.2.2 and perform a Zero Gas Calibration
and a Span Gas Calibration.
6.2 Adjusting
Perform the following procedures if 4.0 mA and 20.0 mA were not
measured at the controller end. If the correct currents were measured,
proceed to 6.3.
The current must be measured at the controller end in 6.2.1 and 6.2.2.
6.2.1 Calibrate 4.0 mA and 20.0 mA
1. From the Main Menu, select the Test Menu ( ).
2. Then select Force mA output ( ).
3. Adjust the current output in the column on the right until the
current at the controller end is 4.0 mA.

XNX Universal Transmitter
Proof Testing Procedure 8Adjusting
Figure 2. Adjusting Current
4. Once the new value is entered, use the switches to move
to the ‘3’ and select ✓ to set the mA output.
If the 20.0 mA output was not equal to 20.0 mA, complete steps #3-4.
6.2.2 Zero Gas Calibration and Span Calibration
The following section outlines the steps for calibrating the attached
XNX sensors. For calibration information for specific sensors, refer to
the XNX Technical Manual.
1. If using a compressed gas cylinder, push the calibration gas
flow housing onto the bottom of the sensor and apply the gas.
2. Access the Calibration Menu.
Figure 3. Gas Calibration Menu
NOTE:
The Gas Calibration Menu is for both Zero Gas and Span Gas
Calibration.
6.2.2.1 Zero Gas Calibration
Sensor Reading
at Current Settings
Figure 4. Zero Gas Calibration Screen
As the sensor detects the zero gas and the concentration
increases, the values displayed will reflect the changing
concentration. When the concentration values are stable select
✓ to allow the XNX to calculate the zero adjustment. Selecting
✖ will return to the Gas Calibration Menu.
Figure 5. Zero Gas Calibration in Progress
3. If the Zero Gas Calibration is successful, the Zero Passed
screen displays.
Figure 6. Zero Gas Calibration Passed

XNX Universal Transmitter
Proof Testing Procedure 9Adjusting
6.2.2.2 Span Calibration
NOTE:
If a Span Calibration is not required, select ✖ to skip the Span
Calibration and return to the Calibration Menu.
1. When the Zero Gas Calibration is complete, the Span
Concentration screen appears. The gas concentration for the
Span Gas Calibration can be changed.
If the Span Calibration is skipped, the Gas Calibration screen
displays.
Figure 7. Span Gas Concentration Screen
2. Enter the concentration of the span gas by selecting ✓ to
choose the first digit and use the switches to increment or
decrement the values. Use ✓ to accept the new value and move
to the next digit. Continue until all digits have been selected.
Sensor Reading
at Current Settings
Calibration Gas
Concentration
Figure 8. Span Calibration Screen
3. Apply the span gas. As the sensor detects the gas and the
concentration increases, the values displayed will reflect the
changing concentration. When the concentration values are
stable select ✓ to perform the span. The Span Calibration
process also determines whether the sensor is within the
proper range to accurately detect the target gas.
Selecting ✖ will cancel the span calibration and return to the
Gas Calibration Menu.
4. When the sensor has completed the calibration and the span
algorithms have determined that it is within range, the Span
Passed screen will appear.
Figure 9. Span Passed Screen

XNX Universal Transmitter
Proof Testing Procedure 10 Verifying mA Settings
If the calibration is not successful, the Span Failed screen will display.
Selecting ✓ will return to the Span Concentration screen to begin
the span calibration again. Selecting ✖ will exit Span Calibration and
return to the Gas Calibration Menu.
Arrow indicates
gas values too low
Selecting ‘✔’ returns to
the Span Concentration
screen
Figure 10. Span Calibration Failed
Once the Zero Gas and Span Gas calibrations are completed
successfully, the user will be prompted to
• exit with inhibit off,
• exit with inhibit on, or
• not exit.
Figure 11. Exiting Zero Gas and Span Gas calibrations
WARNING
While XNX is in Inhibit Mode, alarms are silenced. This will prevent
an actual gas event from being reported. Inhibit Mode must be reset
after testing or maintenance activities.
6.3 Verifying mA Settings
The mA levels output for inhibiting alarms during maintenance/testing,
warnings triggered by the XNX, overrange conditions, Beam Blocked
and Low Signal for the Searchpoint Optima Plus and Searchline Excel
gas detectors must be verified.
1. From the Main Menu, select the Configure Menu ( ). From
the Configure Menu, select mA Levels.
Figure 12. mA Levels Menu
2. Use the switches to move to the mA output to be changed
and use ✓ to select it.
✓
Figure 13. Set mA Levels for Warning
3. Refer to Table 6 for the mA levels. If the values do not match
the values in the table, proceed to step #4 to adjust the values.
NOTE
If the values for the faults and warnings have been changed
from the default settings since installation, ensure the current
output matches those changed values.