Honeywell oneWireless XYR 6000 User manual

OneWireless
XYR 6000 Transmitters
Quick Start Guide
34-XY-25-21
Revision 3
8/28/07

ii OneWireless XYR 6000 Transmitters Quick Start Guide Revision 3
8/28/2007
Notices and Trademarks
Copyright 2007 by Honeywell International Inc.
Revision 3 August 28, 2007
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may
be stated in its written agreement with and for its customers.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.
Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
Other brand or product names are trademarks of their respective owners.
Honeywell International
Process Solutions
2500 West Union Hills
Phoenix, AZ 85027
1-800 343-0228

Revision 3 OneWireless XYR 6000 Transmitters Quick Start Guide iii
8/8/07
About This Document
This document describes mounting, installation and wiring of the XYR 6000 Wireless Transmitters and antennae.
Configuration, authentication and operation are covered in other documents.
Honeywell does not recommend using devices for critical control where there is a single point of failure or where
single points of failure result in unsafe conditions. The initial release of OneWireless (R100) is targeted at open
loop control, supervisory control, and controls that do not have environmental or safety consequences. As with any
process control solution, the end-user must weigh the risks and benefits to determine if the products used are the
right match for the application based on security, safety, and performance. Additionally, it is up to the end-user to
ensure that the control strategy sheds to a safe operating condition if any crucial segment of the control solution
fails.
Revision Information
Document Name Document ID Revision
Number Publication Date
XYR 6000 Transmitters Quick Start Guide 34-XY-25-21 1 6/7/07
2 8/7/07
3 8/28/2007
References
The following list identifies all documents that may be sources of reference for material discussed in this
publication.
Document Title
Getting Started with Honeywell OneWireless Solutions
OneWireless Wireless Builder User’s Guide
OneWireless Builder Parameter Reference
OneWireless XYR 6000 Pressure Transmitter User's Manual
OneWireless XYR 6000 Temperature Transmitter User's Manual
OneWireless XYR 6000 SmartCET Corrosion Transmitter User's Manual
OneWireless XYR 6000 HLAI Transmitter User's Manual

iv OneWireless XYR 6000 Transmitters Quick Start Guide Revision 3
8/8/07
Support and contact info
United States and Canada
Contact: Honeywell Solution Support Center
Phone: [phone]. In Arizona: 602- 313-5558
Calls are answered by dispatcher between 6:00 am and 4:00 pm Mountain Standard Time.
Emergency calls outside normal working hours are received by an answering service and
returned within one hour.
Facsimile: [phone]
Mail: Honeywell TAC, MS P13
2500 West Union Hills Drive
Phoenix, AZ, 85027
EuropeContact: Honeywell TAC-EMEA
Phone: [phone]
Facsimile: [phone]
Mail: TAC-BE02
Hermes Plaza
Hermeslaan, 1H
B-1831 Diegem, Belgium
Pacific Contact: Honeywell Global TAC – Pacific
Phone: [phone] (toll free within Australia)
[phone] (outside Australia)
Facsimile: [phone]
Mail: Honeywell Limited Australia
5 Kitchener Way
Burswood 6100, Western Australia
Email: [e-mail]
India Contact: Honeywell Global TAC – India
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Automation India Ltd.
56 and 57, Hadapsar Industrial Estate
Hadapsar, Pune –411 013, India
Email: [e-mail]
Korea Contact: Honeywell Global TAC – Korea
Phone: [phone]
[phone]
Facsimile: [phone]
Mail: Honeywell Co., Ltd
17F, Kikje Center B/D,
191, Hangangro-2Ga
Yongsan-gu, Seoul, 140-702, Korea
Email: [e-mail]

Revision 3 OneWireless XYR 6000 Transmitters Quick Start Guide v
8/8/07
People’s Republic of China
Contact: Honeywell Global TAC – China
Phone: [phone]
Mail: Honeywell (China) Co., Ltd
33/F, Tower A, City Center, 100 Zunyi Rd.
Shanghai 200051, People’s Republic of China
Email: [e-mail]
Singapore
Contact: Honeywell Global TAC – South East Asia
Phone: [phone]
Facsimile: [phone]
[phone]
Mail: Honeywell Private Limited
Honeywell Building
17, Changi Business Park Central 1
Singapore 486073
Email: [e-mail]
Taiwan Contact: Honeywell Global TAC – Taiwan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Taiwan Ltd.
17F-1, No. 260, Jhongshan 2nd Road.
Cianjhen District
Kaohsiung, Taiwan, ROC
Email: [e-mail]
Japan Contact: Honeywell Global TAC – Japan
Phone: [phone]
Facsimile: [phone]
Mail: Honeywell Japan Inc.
New Pier Takeshiba, South Tower Building,
20th Floor, 1-16-1 Kaigan, Minato-ku,
Tokyo 105-0022, Japan
Email: [e-mail]
World Wide Web
Honeywell Solution Support Online:
http://www.honeywell.com/ps
Elsewhere
Call your nearest Honeywell office.
Training Classes
Honeywell Automation College:
http://www.automationcollege.com

vi OneWireless XYR 6000 Transmitters Quick Start Guide Revision 3
8/8/07
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.
CAUTION Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in serious injury or death.
WARNING symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS
LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.
ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.
Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.
Functional earth terminal: Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to Protective Earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground:Functional earth connection. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.
Chassis Ground: Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.

Revision 3 OneWireless XYR 6000 Transmitters Quick Start Guide vii
8/8/07
Contents
1. INTRODUCTION.................................................................................................... 1
1.1 Site preparation ............................................................................................................................1
1.2 Certifications and approvals ....................................................................................................... 1
Hazardous location certifications............................................................................................................................1
Radio certifications.................................................................................................................................................1
Approval ratings .....................................................................................................................................................2
2. TRANSMITTER MOUNTING................................................................................. 3
2.1 Weight............................................................................................................................................ 3
2.2 Dimensions ...................................................................................................................................3
2.3 Transmitter location.....................................................................................................................9
Pressure models....................................................................................................................................................9
2.4 Bracket mounting.........................................................................................................................9
Attach bracket to pipe.............................................................................................................................................9
Attach transmitter to bracket ................................................................................................................................10
2.5 Rotate transmitter housing........................................................................................................ 11
2.6 Rotate display.............................................................................................................................11
Tools required ......................................................................................................................................................11
Procedure.............................................................................................................................................................11
3. PROCESS INSERTION........................................................................................13
3.1 Pressure models......................................................................................................................... 13
Piping...................................................................................................................................................................13
Process connections............................................................................................................................................15
General piping guidelines.....................................................................................................................................15
3.2 Temperature models .................................................................................................................. 16
Insert probe into process......................................................................................................................................16
Integral probe wiring.............................................................................................................................................16
Remote probe wiring............................................................................................................................................16
3.3 HLAI models................................................................................................................................ 17
Connect wiring .....................................................................................................................................................17
3.4 Corrosion models.......................................................................................................................18
Probe mounting locations.....................................................................................................................................18
Probe installation..................................................................................................................................................21
Connect wiring .....................................................................................................................................................22
4. ANTENNA ADJUSTMENT AND MOUNTING......................................................23
4.1 Requirements.............................................................................................................................. 23
Radio installation requirements............................................................................................................................23

Contents
Symbol Definitions
viii OneWireless XYR 6000 Transmitters Quick Start Guide Revision 3
8/8/07
4.2 Integral antenna.......................................................................................................................... 23
Elbow................................................................................................................................................................... 24
Straight ................................................................................................................................................................ 24
4.3 Remote antenna..........................................................................................................................25
Outdoor installation warnings............................................................................................................................... 25
Directional mounting procedure........................................................................................................................... 27
Omnidirectional mounting procedure................................................................................................................... 28
Connect antenna to transmitter............................................................................................................................ 28
5. START UP............................................................................................................29
5.1 Connect batteries .......................................................................................................................29
5.2 Display sequence .......................................................................................................................30
5.3 Authentication............................................................................................................................. 30
6. CSA CERTIFIED DIVISION 2 / ZONE 2 INSTALLATION DRAWINGS...............31

Contents
Tables
Revision 3 OneWireless XYR 6000 Transmitters Quick Start Guide ix
8/8/07
Tables
Table 2-1 Display adjustment .....................................................................................................................12

Contents
Figures
x OneWireless XYR 6000 Transmitters Quick Start Guide Revision 3
8/8/07
Figures
Figure 1 Temperature/HLAI/Corrosion transmitter dimensions....................................................................3
Figure 2 Temperature/HLAI/Corrosion antenna dimensions........................................................................4
Figure 3 DP/DHGP Pressure transmitter dimensions...................................................................................5
Figure 4 DP/DHGP Pressure antenna dimensions.......................................................................................6
Figure 5 GP/AP Pressure transmitter dimensions........................................................................................7
Figure 6 GP/AP Pressure antenna dimensions............................................................................................ 8
Figure 7 Common bracket orientations.........................................................................................................9
Figure 8 Rotating transmitter housing.........................................................................................................11
Figure 9 Display rotation.............................................................................................................................12
Figure 10 Typical 3-valve manifold and blow-down piping arrangment......................................................13
Figure 11 Typical Arrangement for ½” NPT Process Connection Piping ...................................................14
Figure 12 Temperature probes ................................................................................................................... 16
Figure 13 HLAI connection .........................................................................................................................17
Figure 14 Voltage input wiring ....................................................................................................................17
Figure 15 Current input wiring.....................................................................................................................17
Figure 16 Corrosion transmitter with remote probe ....................................................................................22
Figure 17 Elbow antenna adjustment .........................................................................................................24
Figure 18 Integral straight antenna.............................................................................................................24
Figure 19 Directional antenna mounting.....................................................................................................27
Figure 20 Omnidirection antenna mounting................................................................................................ 28
Figure 21 Battery assembly ........................................................................................................................30