Honeywell STT700 SmartLine User manual

Honeywell Process Solutions
STT700 Series HART/DE Option
User’s Manual
34-TT-25-18
Revision 1
July 2017

Page ii STT700 Series HART/DE Option User’s Manual Revision 1
Copyrights, Notices and Trademarks
© Copyright 2017 by Honeywell, Inc.
Revision 1, July 2017
While the information in this document is presented in good faith and believed to be
accurate, Honeywell disclaims any implied warranties of merchantability and fitness for a
particular purpose and makes no express warranties except as may be stated in the written
agreement with and for its customers. In no event is Honeywell liable to anyone for any
indirect, special, or consequential damages. The information and specifications in this
document are subject to change without notice.
Honeywell, TDC 3000, SFC, SmartLine, PlantScape, Experion PKS, and TotalPlant are
registered trademarks of Honeywell International Inc. Other brand or product names and
service marks are the property of their respective owners.
Honeywell Process Solutions
1250 W Sam Houston Pkwy S
Houston, TX 77042

Revision 1 STT700 Series HART/DE Option User’s Manual Page iii
About This Manual
This manual provides the details of programming Honeywell STT700 SmartLine Temperature
Transmitters for applications involving HART versions 5, 6, and 7 and Honeywell’s Digitally
Enhanced (DE) communication protocols. For installation, wiring, and maintenance information
refer to the STT700 SmartLine Temperature Transmitter User Manual, document number
#34-TT-25-17.
The configuration of your transmitter depends on the mode of operation and the options selected
for it with respect to operating controls, displays and mechanical installation. Details for
operations involving the Honeywell Multi-Communication MC Toolkit (MCT404) are provided
only to the extent necessary to accomplish the tasks-at-hand. Refer to the associated MC Toolkit
User Manual, document # 34-ST-25-50 (MCT404) for complete details. The “Reference” section
in the front matter of this manual lists document titles and numbers.
The STT700 SmartLine Temperature Transmitter can be digitally integrated with one of two
Honeywell systems:
Experion PKS: you will need to supplement the information in this document with the data and
procedures in the Experion Knowledge Builder.
Honeywell’s TotalPlant Solutions (TPS): you will need to supplement the information in this
document with the data in the PM/APM SmartLine Transmitter Integration Manual, which is
supplied with the TDC 3000 book set. (TPS is the evolution of the TDC 3000).
Release Information
STT700 Series HART/DE Option User Manual, Document # 34-TT-25-18 (this document)
Rev. 1 July 2017 1st Release
References
The following list identifies publications that may contain information relevant to the information
in this document.
STT700 SmartLine Temperature Transmitter Quick Start Installation Guide, # 34-TT-25-19
STT700 SmartLine Temperature Transmitter w/ HART/DE Comms Safety manual, 34-TT-25-20
STT700 SmartLine Temperature Transmitter User manual, # 34-TT-25-17
FDM Offline Configuration User’s manual, # 34-CT-25-01.
MC Toolkit (MCT404) User Manual, Document # 34-ST-25-50
PM/APM SmartLine Transmitter Integration manual, # PM 12-410
STT700 Series Temperature, Transmitter, Agency IS Control Drawing, #50133855
MC Toolkit Modem Code Download Instruction Manual, Document # 34-ST-25-33

Page iv STT700 Series HART/DE Option User’s Manual Revision 1
Patent Notice
The Honeywell STT700 SmartLine Temperature Transmitter family is covered by one or more of the
following U. S. Patents: 5,485,753; 5,811,690; 6,041,659; 6,055,633; 7,786,878; 8,073,098; and other
patents pending.
Support and Contact Information
For Europe, Asia Pacific, North and South America contact details, see back page or refer to the
appropriate Honeywell Solution Support web site:
Honeywell Corporate www.honeywell.com
Honeywell Process Solutions www.honeywellprocess.com
SmartLine Temperature https://www.honeywellprocess.com/smartline-temperature/
Training Classes http://www.automationccollege.com
Telephone and Email Contacts
Area
Organization
Phone Number
United States and
Canada
Honeywell Inc.
1-800-343-0228 Customer Service
1-800-423-9883 Global Technical Support
Global email
Support
Honeywell Process
Solutions
[email protected]

Revision 1 STT700 Series HART/DE Option User’s Manual Page v
Contents
1STT700 Physical and Functional Characteristics...........................................................................8
1.1 Overview ................................................................................................................................8
1.2 Features and Options..............................................................................................................9
1.2.1 Physical Characteristics................................................................................................10
1.2.2 Functional Characteristics ............................................................................................11
1.3 STT700 SmartLine Transmitter Nameplate .........................................................................11
1.4 Safety Certification Information...........................................................................................12
1.5 Transmitter Adjustments ......................................................................................................12
1.6 EU Meters Options...............................................................................................................12
2Communication Modes ................................................................................................................13
2.1 Overview ..............................................................................................................................13
2.2 Digitally Enhanced (DE) Mode Communication.................................................................13
2.3 HART Mode Communication ..............................................................................................14
3Configuration Tools and Interfaces..............................................................................................15
3.1 Overview ..............................................................................................................................15
3.2 Pre-requisites........................................................................................................................15
3.3 Application Design, Installation, Startup, and Operation.....................................................15
3.3.1 Organization .................................................................................................................15
3.4 MC Toolkit Participation......................................................................................................16
3.4.1 MC Toolkit Software Applications ..............................................................................16
3.4.2 Configuration Databases ..............................................................................................16
3.4.3 Configuration................................................................................................................16
3.4.4 MC Toolkit Transmitter Electrical/Signal Connections...............................................17
4DE Transmitter Configuration......................................................................................................18
4.1 Configuration Personnel Requirements................................................................................18
4.2 MC Toolkit Software Application Overview .......................................................................18
4.3 DE Transmitter Online Configuration..................................................................................19
4.3.1 Uploading a Transmitter Configuration .......................................................................19
4.3.2 Device Information Configuration ...............................................................................21
4.3.3 General Configuration Parameters ...............................................................................22
4.3.4 DE-Specific Configuration Parameters ........................................................................23
4.3.5 DE Auxiliary Configuration.........................................................................................24
4.3.6 DE Monitor Status........................................................................................................24
4.3.7 Saving the Configuration to File ..................................................................................26
4.3.8 DE Online Configuration Summary.............................................................................27
4.4 DE Transmitter Offline Configuration .................................................................................27
4.4.1 Overview ......................................................................................................................27
4.4.2 DE Offline File Management.......................................................................................27
4.4.3 Save to a File ................................................................................................................28
4.4.4 Downloading in DE Offline Mode...............................................................................28
4.4.5 DE Offline Parameterization ........................................................................................28
5HART Transmitter Configuration................................................................................................29
5.1 Overview ..............................................................................................................................29
5.1.1 Personnel Requirements...............................................................................................29

Page vi STT700 Series HART/DE Option User’s Manual Revision 1
5.2 Overview of FDC Homepage .............................................................................................. 30
5.2.1 Settings......................................................................................................................... 31
5.2.2 Manage DDs ................................................................................................................ 32
5.2.3 Online configuration .................................................................................................... 34
5.2.4 Offline configuration.................................................................................................... 34
5.2.5 Online Configuration Overview................................................................................... 34
5.2.6 Overview of Device Homepage................................................................................... 35
5.2.7 Tabs on the Device Home page ................................................................................... 36
5.2.8 Using FDC for various device operations.................................................................... 38
5.2.9 Device Configuration and Parameter Descriptions...................................................... 40
5.2.10 Procedure to Enter the Transmitter Tag....................................................................... 57
5.2.11 Selecting the Process Variable (PV) Unit of Temperature Measurement.................... 57
5.2.12 Setting PV URV, and LRV Values.............................................................................. 58
5.2.13 Setting Range Values for Applied Temperature .......................................................... 58
5.2.14 Saving device history................................................................................................... 59
5.2.15 Exporting device history records to FDM.................................................................... 60
5.2.16 Exporting device history records to DocuMint............................................................ 61
5.2.17 Custom Views.............................................................................................................. 61
5.2.18 Offline Configuration................................................................................................... 63
6DE Calibration ............................................................................................................................. 66
6.1 Overview.............................................................................................................................. 66
6.2 Calibration Recommendations............................................................................................. 66
6.3 Test Equipment Required for Calibration............................................................................ 66
6.4 Analog Output Signal Calibration........................................................................................ 67
6.5 Calibrating Range Using the MC Toolkit............................................................................ 69
6.6 Conditions for Input Calibration.......................................................................................... 69
6.7 Input Calibration Procedures Description............................................................................ 69
6.8 Input Calibration Procedure................................................................................................. 70
6.8.1 Correct Input at the Lower Range Value (LRV).......................................................... 70
6.8.2 Correct Input at URV................................................................................................... 71
6.9 DE Output Calibration ......................................................................................................... 73
6.9.1 Output Calibration Preparation .................................................................................... 73
6.10 Manually Setting the Process Variable Range..................................................................... 76
6.11 Procedure to Reset Calibration ............................................................................................ 79
7HART Calibration........................................................................................................................ 81
7.1 About This Section .............................................................................................................. 81
7.1.1 About Calibration......................................................................................................... 81
7.1.2 Equipment Required .................................................................................................... 81
7.1.3 Input Calibration Procedure......................................................................................... 82
7.1.4 Correct Input at Sensor 1 / 2 Calibration High Point................................................... 84
7.2 Analog Output Signal Calibration........................................................................................ 87
7.3 Calibrating Analog Inputs.................................................................................................... 88
7.3.1 Correcting the Low Calibration Point.......................................................................... 88
7.3.2 Correcting the High Calibration Point ......................................................................... 89
7.3.3 Resetting Calibration.................................................................................................... 89
7.3.4 STT700 Calibration Records ....................................................................................... 90

Revision 1 STT700 Series HART/DE Option User’s Manual Page vii
8HART Advanced Diagnostics......................................................................................................91
8.1 About This Section...............................................................................................................91
8.2 Advanced Diagnostics..........................................................................................................91
8.2.1 Transmitter Install Date................................................................................................91
8.2.2 PV Tracking Diagnostics..............................................................................................92
8.2.3 Cold Junction Tracking ................................................................................................95
8.2.4 CT Tracking Diagnostics..............................................................................................97
8.2.5 Installation and Device Life .........................................................................................98
8.2.6 Operating Voltage Diagnostics.....................................................................................98
8.2.7 Power Up Diagnostics..................................................................................................99
9Troubleshooting and Maintenance .............................................................................................100
9.1 HART Diagnostic Messages ..............................................................................................100
9.2 DE Diagnostic Details........................................................................................................102
10 - DTMs.......................................................................................................................................104
10.1 Introduction ........................................................................................................................104
10.2 Components........................................................................................................................104
10.3 Downloads..........................................................................................................................104
10.4 Procedure to Install and Run the DTM...............................................................................104
10.5 STT700 Dashboard.............................................................................................................105
10.6 STT700 Online Parameterization.......................................................................................105
10.6.1 Device Health.............................................................................................................106
10.6.2 Device Icon / Honeywell Logo...................................................................................106
10.6.3 Process Variables........................................................................................................106
10.6.4 Shortcuts.....................................................................................................................106
10.7 Basic Configuration Page...................................................................................................107
10.7.1 Device Information.....................................................................................................107
10.7.2 Model Number............................................................................................................107
10.7.3 Device Assembly........................................................................................................107
10.8 STT700 Offline Parameterization ......................................................................................108
11 HART DD Binary File Format Compatibility Matrix................................................................109
Glossary..............................................................................................................................................110

Page viii STT700 Series HART/DE Option User’s Manual Revision 1
List of Figures
Figure 1 –STT700 HART Temperature Transmitter module ............................................................. 10
Figure 2 –STT700 DE Temperature Transmitter module................................................................... 10
Figure 3 –Nameplate on the side of the transmitter............................................................................ 11
Figure 4 –Typical STT700 Nameplate................................................................................................. 12
Figure 5 –DE Mode Value Scaling..................................................................................................... 13
Figure 6 –HART Point-to-Point and Multi-drop Value Scaling......................................................... 14
Figure 7 –MC Toolkit-Transmitter Electrical/Signal Connections..................................................... 17
Figure 8 –FDC Homepage.................................................................................................................. 30
Figure 9 –Device Homepage............................................................................................................... 35
Figure 10 –Analog Output Calibration Test Setup ............................................................................. 67
Figure 11 –Input Calibration Connections.......................................................................................... 70
Figure 12 –Output Calibration Test Connections ............................................................................... 73
Figure 13 –DE Analog Mode Scaling and Test Connections ............................................................. 74
Figure 14 –Setup to Manually Set the PV LRV and URV ................................................................. 76
List of Tables
Table 1 –Features and Options ............................................................................................................. 9
Table 2 –Available EU Meter Characteristics .................................................................................... 12
Table 3 –Device Information Parameters ........................................................................................... 21
Table 4 –General Configuration Parameters....................................................................................... 22
Table 5 –DE Configuration Parameters.............................................................................................. 23
Table 6 –Monitor Parameters.............................................................................................................. 25
Table 7 –FDC homepage elements..................................................................................................... 30
Table 8 –Device health status ............................................................................................................. 35
Table 9 –HART Transmitter Parameters ............................................................................................ 40
Table 10 –Basic Configuration ........................................................................................................... 40
Table 11 –Advanced Configuration.................................................................................................... 43
Table 12 –Monitor .............................................................................................................................. 51
Table 13 –Calibration Records ........................................................................................................... 90
Table 14 –Viewing Advanced Diagnostics......................................................................................... 91
Table 15 –PV Tracking....................................................................................................................... 92
Table 16 –Cold Junction Tracking...................................................................................................... 95
Table 17 –Core Temperature Diagnostics .......................................................................................... 97
Table 18 –Installation and Device Life Diagnostics........................................................................... 98
Table 19 –Operating Voltage Diagnostics.......................................................................................... 98
Table 20 –Power Up Diagnostics........................................................................................................ 99
Table 21 –HART Diagnostic Messages............................................................................................ 100
Table 22 –DE Critical and Non-Critical Diagnostic Details............................................................. 102
1 STT700 Physical and Functional Characteristics
1.1 Overview
This section is an introduction to the physical and functional characteristics of Honeywell’s STT700
SmartLine Temperature Transmitter.

Revision 1 STT700 Series HART/DE Option User’s Manual Page 9
1.2 Features and Options
The STT700 SmartLine Temperature Transmitter is available in a variety of models for measuring
thermocouples, RTD and millivolts and ohm sensor types. Table 1 lists the protocols, human machine
interface (HMI), materials, approvals, and mounting bracket options for the STT700.
Table 1 –Features and Options
Feature/Option
Standard/Available Options
Communication Protocols
HART version 7, Digitally Enhanced (DE)
Human-Machine Interface (HMI)
Options
No Display
EU Meter
Calibration
Two-point
Approvals (See Appendix C for
details.)
ATEX, CSA, FM, IECx
Mounting Brackets
Pipe mounting and wall mounting brackets in carbon steel and
316 stainless steel.
Integration Tools
Smart Field Communicator (SFC),
SmartLine Configuration Tool kit (SCT),
MC Toolkit (MCT404),
Experion,
Field Device Manager (FDM) and Device Type Manager (DTM)

Page 10 STT700 Series HART/DE Option User’s Manual Revision 1
1.2.1 Physical Characteristics
As shown in Figure 1 and Figure 2, the STT700 is packaged in a single module. The elements in this
module are connected to the process sensors, measure the process variables, respond to setup
commands and execute the software and protocol for the different temperature measurement types.
Figure 1 –STT700 HART Temperature Transmitter module
Figure 2 –STT700 DE Temperature Transmitter module

Revision 1 STT700 Series HART/DE Option User’s Manual Page 11
1.2.2 Functional Characteristics
The transmitter measures process temperature and outputs a signal proportional to the measured
process variable (PV). Available output communication protocols include analog 4 to 20 mA,
Honeywell Digitally Enhanced (DE) and HART protocols.
To set up and make adjustments, the Honeywell Multi-Communication (MC) Toolkit (not supplied
with the transmitter) can facilitate setup and adjustment procedures in the case of HART and DE.
Certain adjustments can be made through an Experion Station or a Universal Station if the transmitter
is digitally integrated with Honeywell’s Experion or TPS/TDC 3000 control system for HART and DE
transmitters.
1.3 STT700 SmartLine Transmitter Nameplate
The transmitter nameplate mounted on the side of the transmitter module (see Figure 4) lists the model
number, physical configuration, electronics options, accessories, certifications, and manufacturing
specialties (see Figure 4).
Figure 3 –Nameplate on the side of the transmitter

Page 12 STT700 Series HART/DE Option User’s Manual Revision 1
Figure 4 is an example of a typical STT700 temperature nameplate. The model number format consists
of a key number with several table selections.
Figure 4 –Typical STT700 Nameplate
The transmitter type can be identified from the key number. The letter in the third digit represents one
of these basic transmitter types:
T = Temperature
For a complete selection breakdown, refer to the Specification and Model Selection Guide provided as
a separate document.
1.4 Safety Certification Information
The approvals name plate contains information and service marks that disclose the transmitter
compliance information. Refer to Appendix A in the STT700 SmartLine Transmitters User’s manual,
document number 34-TT-25-17 for details.
1.5 Transmitter Adjustments
For HART and DE, the Honeywell MC Toolkit or other third-party hand-held can make any
adjustments to a STT700 SmartLine Temperature Transmitter. Alternately, certain adjustments can be
made through the Experion or Universal Station, if the transmitter is digitally integrated with a
Honeywell Experion or TPS system.
1.6 EU Meters Options
The STT700 SmartLine Temperature Transmitter is offered with an EU Meter or no display options, see Table 2
Table 2 –Available EU Meter Characteristics
EU Meter
Compatibility for replacement of existing STT250 installations
360orotation in 90oincrements
Standard units of measurement: °F, °C, °R, K, Ω, mV & %
Key I II III IV VVI VII VIII
STT700 - _ _ - _ _ _ - _ _ _ _ _ _ - _ _ _ _ - _ _ _ - _ - _ _, _ _, _ _ - 00000

Revision 1 STT700 Series HART/DE Option User’s Manual Page 13
2 Communication Modes
2.1 Overview
The STT700 SmartLine Temperature Transmitter can be configured for operation with Honeywell’s
Digitally Enhanced (DE) communication protocol and HART version 7 communication. This manual
addresses the processes to configure and calibrate a transmitter for DE and HART communication.
2.2 Digitally Enhanced (DE) Mode Communication
Although it is unnecessary to put a control loop in manual mode before communicating
with a transmitter operating in DE mode, caution is required if there is potential for error in
identifying the operating mode.
In DE mode, the PV is available for monitoring and control purposes.
Much of the operation in the Digitally Enhanced (DE) mode is similar to that of analog operation. The
essential characteristics of DE mode operation are shown in Figure 5.
Figure 5 –DE Mode Value Scaling
As indicated at the right of Figure 5, output values of process variables, as well as communications are
transferred to a receiving device digitally. The digital coding is Honeywell proprietary, which requires
the use of DE-capable Honeywell control equipment.
The use of DE mode offers several advantages:
Process Safety: Unlike analog mode, communications devices do not bump the PV value.
Accuracy: Requires less maintenance.
Digital communication: Relatively immune to small variations in circuit resistance or supply
voltage.
Facilitates Maintenance Tasks: Honeywell control systems include operating displays that
enable direct communication with transmitters operating in DE mode.

Page 14 STT700 Series HART/DE Option User’s Manual Revision 1
2.3 HART Mode Communication
When using MCT404, but before connecting to a HART transmitter, verify that the FDC
application is used and not the MC Toolkit application. When using the MC Toolkit application,
the MCT404 is set for DE communications, where the current amplitude can bump process
variables in either point-to-point or in the multi-drop mode in HART.
Transmitters with HART capability have features that vary among manufacturers and
with the characteristics of specific devices. The FDC software application executing on
the MCT404 supports the HART Universal, Common Practice and Device Specific
Commands which are implemented in the Honeywell transmitters.
As indicated in Figure 6, the output of a transmitter configured for HART protocol includes two
primary modes:
Figure 6 –HART Point-to-Point and Multi-drop Value Scaling
Point-to-Point Mode, in which one transmitter is connected via a two-conductor, 4-20 mA
current loop to one receiver.
Multi-Drop Mode, in which several transmitters are connected through a two-conductor
network to a multiplexed receiver device.
In point-to-point mode, the value of the primary Process Variable (PV) is represented by a 4-20 mA
current loop, and is almost identical to that of a transmitter operating in analog mode. Additionally,
one device can reside in analog output mode when it is configured in multi-drop. In this case, however,
the analog signal is modulated by Frequency Shift Keying (FSK), using frequencies and current
amplitude that do not affect analog sensing at the receiver. The accuracy of the analog value must be
precisely controlled for accurate sensing. HART communication will not bump process variables.
In multi-drop mode, up to 16 transmitters in HART 5 (addresses 0-15) and up to 64 transmitters in
HART6/7 (addresses 0-63) can exist on the two-conductor network.

Revision 1 STT700 Series HART/DE Option User’s Manual Page 15
3 Configuration Tools and Interfaces
3.1 Overview
This section describes the tools and interfaces involved in configuring a new STT700 SmartLine
Temperature Transmitter for HART or DE communication operation. The information in this section
also applies to adjusting the configuration of a transmitter that has been in operation and updating one
that is currently in operation.
3.2 Pre-requisites
The information and procedures in this manual are based on the assumption that personnel performing
configuration and calibration tasks are fully qualified and knowledgeable in the use of the Honeywell
MC Toolkit MCT404. The reference to MC Toolkit, Toolkit and MCT404 are used interchangeably as
MCT404 is the model name for the Honeywell MC Toolkit product.
Furthermore, we assume that the reader is intimately familiar with the STT700 SmartLine
Temperature Transmitter and thoroughly experienced in the type of process application targeted for
transmitter deployment. Therefore, detailed procedures are supplied only in so far as necessary to
ensure satisfactory completion of configuration tasks.
3.3 Application Design, Installation, Startup, and Operation
The STT700 SmartLine Temperature Transmitters User’s Manual, document number 34-TT-25-17,
provides the details for Application Design, Installation and Startup, Operation, Configuration tools,
Maintenance and Calibration.
3.3.1 Organization
This information in this section is arranged in the following sequence:
MC Toolkit participation in STT700 transmitter setup and configuration:
1. Physical circuit connections
2. Application components
3. Configuration for analog, DE and HART operation
STT700 transmitter
1. Health indications
2. Ability to be configured and operate in a process system

Page 16 STT700 Series HART/DE Option User’s Manual Revision 1
3.4 MC Toolkit Participation
Before using the MC Toolkit, be sure that you are aware of the potential consequences of
each procedure, and that you use appropriate safeguards to avoid possible problems. For
example, if the transmitter is an element in a control loop, the loop needs to be put in manual
mode, and alarms and interlocks (i.e., trips) need to be disabled, as appropriate, before starting
a procedure.
3.4.1 MC Toolkit Software Applications
The MC Toolkit has two software applications that apply to the STT700 SmartLine Temperature
Transmitter, which are:
Field Device Configurator (FDC). This application is used for configuring, calibrating,
monitoring, and diagnosing HART devices. FDC conforms to the IEC 61804-3 EDDL
(Electronic Data Description Language) standard specification. The FDC application is an open
solution that supports devices with a registered device description (DD) file compatible with
HART Communication Foundation (HCF) requirements.
MC Toolkit. This application is used for configuring, calibrating, monitoring, and diagnosing
Honeywell Digitally Enhanced (DE) devices.
Details for working with the MC Toolkit are provided in the MC Toolkit User Manual, document #34-
ST-25-50 (MCT404). In subsequent sections of this manual, explicit operating instructions are
provided only in so far as necessary to complete required tasks and procedures.
3.4.2 Configuration Databases
The MC Toolkit is used to establish and/or change selected operating parameters in a transmitter
database.
3.4.3 Configuration
Configuration can be accomplished both online and offline with the transmitter powered up and
connected to the MC Toolkit. Online configuration immediately changes the transmitter operating
parameters. For offline configuration, transmitter operating characteristics are entered into the MC
Toolkit memory for subsequent downloading to a transmitter.
When you set up or configure a transmitter, it can take up to 30 seconds for the value to
be stored in it. If you change a value and transmitter power is interrupted before the change
is copied to nonvolatile memory, the changed value will not be moved to nonvolatile memory.

Revision 1 STT700 Series HART/DE Option User’s Manual Page 17
3.4.4 MC Toolkit Transmitter Electrical/Signal Connections
Figure 7 displays how to connect the MC Toolkit directly to the terminals of a HART or DE
transmitter (top) and a HART-only transmitter (bottom).
Figure 7 –MC Toolkit-Transmitter Electrical/Signal Connections

Page 18 STT700 Series HART/DE Option User’s Manual Revision 1
4 DE Transmitter Configuration
4.1 Configuration Personnel Requirements
The configuration processes in this section reflect the assumption that you will use the Honeywell MC
Toolkit configuration tool to configure an STT700 SmartLine Temperature Transmitter. The MC
Toolkit application is used to configure Honeywell ST 3000 and SmartLine Pressure Transmitter, STT
3000 Smart Temperature Transmitters, as well as the STT700 SmartLine Temperature Transmitter.
Throughout, the term transmitter means the STT700 SmartLine Temperature Transmitter.
The other tools that support DE transmitter configuration are the SmartLine Configuration Toolkit
(SCT 3000), Experion PKS, and Smart Field Communicator (SFC).
4.2 MC Toolkit Software Application Overview
Each new STT700 SmartLine Temperature Transmitter is shipped from the factory with a basic
configuration installed. This basic configuration must be edited or revised to meet the requirements of
your process system.
The MC Toolkit application supports both online and offline configuration.
Online operation establishes communication with a DE transmitter for the following tasks:
oUpload a transmitter database.
oConfigure transmitter parameters.
oCalibrate a transmitter.
oExecute diagnostics.
oSave a configuration to a file.
Offline operation allows to the selection of a basic template, the ability to edit the parameters
and the ability download to a transmitter after establishing communication with it. Parameter
updates can also be saved in a file without actually downloading them to the transmitter.
Specific operating details for the MC Toolkit displays are provided in “MC Toolkit Application
Software Display Conventions,” of the MC Toolkit User Manual, (document number #34-ST-25-50
for MCT404) for the following:
Navigation
The MC Toolkit Menu Bar
File Menu
Modem Menu
Help Menu
Data Entry and Display

Revision 1 STT700 Series HART/DE Option User’s Manual Page 19
4.3 DE Transmitter Online Configuration
Online configuration consists of establishing communication between the MC Toolkit and a
transmitter configured for DE communication. Each transmitter has a configured database, whether
new from the factory, a spare, or one to be reconfigured. In any case, the MC Toolkit application is
used to upload the existing configuration from the transmitter for review and editing.
4.3.1 Uploading a Transmitter Configuration
1. Connect a DE transmitter to the MC Toolkit. Be sure that both devices have power applied.
2. Start the MC Toolkit application by selecting Start / MC Toolkit on the MC Toolkit /
MCT404/202. The MC TOOLKIT Home page will be displayed, see below figure.
3. Select the Online button, and establish communication between the Toolkit and the
transmitter.
4. When the warning message for connecting to a DE device appears, select OK.
5. Process and respond to the three warning pop-ups as appropriate, and then select OK in the
Put loop in Manual… pop-up. The QUICK MONITOR box will be displayed. Typical Quick
Monitor dialog is shown below (note that Type will be shown as STT3000).

Page 20 STT700 Series HART/DE Option User’s Manual Revision 1
6. Select Upload. A progress bar will be displayed on the QUICK MONITOR box, and when the
upload is complete, the DE MAIN MENU will be displayed. Typical DE Main Menu dialog is
shown below.
A confirmation request message will be displayed if you select <Back for a transmitter
that was previously set to Output Mode during calibration, and was not subsequently cleared.
If you confirm the message (Yes answer), the display will exit the DE MAIN MENU.