Horizon Fitness P8000 User manual

INDOOR CYCLE OWNER’S MANUAL
P8000

2

3
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
When using an exercise product, basic precautions should always be followed, including the following: Read all instructions
before using this indoor cycle. It is the responsibility of the owner to ensure that all users of this indoor cycle are adequately
informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact Customer Tech
Support at the number listed on the back panel.

4
READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS
INDOOR CYCLE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY
INSTRUCTIONS.
•CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your
physician before continuing.
•Use this cycle for its intended purpose as described in this manual. Do not use attachments that have not been recommended by
the manufacturer.
•Never operate the cycle if it is not working properly, or if it has been damaged. Contact Horizon Fitness or the authorized dealers
for examination and repair.
•Do not use the cycle without proper footwear. NEVER operate the cycle with bare feet.
•Do not wear any clothing that might catch on any moving parts of this cycle.
•Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.
•Do not dismount the cycle until the pedals are at a complete STOP.
•Do not attempt to ride the cycle in a standing position at high RPMs until you have practiced at slower speeds.
•Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other potentially
moving part of the cycle.
•Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Horizon Fitness
or the authorized dealers.
•Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
•Close supervision is necessary when used near children, invalids or disabled people.
•When the cycle is in use, young children and pets should be kept at least 3 meters / 10 feet away.
•After exercising, push down on the tension knob or turn the tension knob in a clockwise direction to slow the flywheel down and
decrease the potential for injury.
•Ensure that adjustment levelers (seat and handlebar height, seat and handlebar fore-and-aft) are properly secured and do not
interfere with range of motion during exercise.
WARNING

5
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to
the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on
the lower front of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON P8000 INDOOR CYCLE
WARNING
SERIAL # PLACEMENT

6
TOOLS/FASTENERS
INCLUDED:
FSocket Head Screw
F5 mm Allen Wrench
FOpen Wrench (#13 / #14 / #15)
PARTS INCLUDED:
A) Main Frame Assembly
B) Handlebar Set
C) Seat
D) Rear Foot
E) Front Foot
F) Pedals
G) Quick Release Lever Set
H) Hardware Kit
If you have questions or if
there are any missing parts,
contact Customer Tech
Support. Contact information
is located on the back panel
of this manual.
NEED HELP?
(A)
(B)
(D)(C)
(H)(G)(F)
(E)
P8000 PARTS INCLUDED

7
This unit weighs 118 lbs / 54 kg. To avoid
injury to the user and the unit, be sure to have
proper assistance to remove or move the unit.
CAUTION
UNPACKING
The P8000 Indoor Cycle is carefully inspected
before it is packaged. Remove all parts from the
shipping carton and foam inserts, and verify that the
following parts are included in your shipment. After
unpacking, dispose of the carton material properly.
NOTE: During each assembly step, ensure that ALL
nuts and bolts are in place and partially threaded in
before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the
installation of hardware. Any grease, such as lithium
bike grease is recommended.
PRE ASSEMBLY
Z01
Z01
Z01
Z01
AT2
D06
AG2
G11
G10
D14
G10
ASSEMBLY EXPLODED DIAGRAM

8
ASSEMBLY STEP 1
A Place the front foot in position at the
front of the cycle, with the transport
wheels facing forward, aligning the
two holes in the foot with the mating
holes in the frame bracket.
B Insert the two screws (Z01) through
the frame bracket and front foot.
Using the #5 Allen Wrench (Z31) to
tighten the screws securely.
C Place the rear foot in position at the
rear of the cycle, aligning the two holes
in the foot with the mating holes in the
frame bracket.
D Insert the two screws (Z01) through the
frame bracket and front foot. Using the
#5 Allen Wrench (Z31) to tighten the
screws securely.
Z01
Z01
Z01
Z01

9
ASSEMBLY STEP 2
G11
G10
A Install the pedals on the pedal cranks by using
the Open Wrench (Z32). The closed end of the
pedal cage must point forward, toward the front
of the cycle.
NOTE: Be careful to align the threads correctly
to avoid damage. A little grease on the threads
should help the pedals to screw in easily
and correctly. Turn the LEFT pedal spindle
COUNTERCLOCKWISE when threading into
the crank arm, and turn the right pedal spindle
clockwise when threading into the crank arm.
C Place the handlebar on the handlebar
stem. Position handlebar bracket beneath
the handlebar stem and insert the quick
release lever set (G10, G11) through the
bottom bracket and into the handlebar.
Turn COUNTERCLOCKWISE to tighten.
D To adjust the position of the handlebar,
loosen quick release lever (G10) and
slide to the desired location.

10
ASSEMBLY STEP 3
A Place the seat on the seat post.
Position seat bracket beneath the
seat post and insert the quick release
lever set (G10, D14) through the
bottom bracket and into the seat. Turn
COUNTERCLOCKWISE to tighten.
B To adjust the forward or backward
position of the seat, loosen quick release
lever and slide to the desired location.
D06
D14
G10
ASSEMBLY COMPLETE!