Hover-1 AXLE User manual

ELECTRIC SCOOTER
AXLE
OPERATION MANUAL
H1-AXL

HELMETS
SAVE
LIVES!
Always wear a properly tted helmet that
complies with CPSC or CE safety standards
when you ride your scooter.
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed
and vulnerable to
serious injury.

PLEASE READ THE USER MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in
the user manual can lead to damage to your Axle, other property
damage, serious bodily injury, and even death.
Thank you for purchasing the Hover-1 Axle Electric Scooter. Please
read all instructions carefully before using and retain this manual for
future use and reference.
This manual applies to the Axle Electric Scooter.
• In order to avoid dangers that are caused by collisions, falls, and
loss of control, please learn how to ride the Axle safely.
• You can learn operating skills by reading the product manual and
watching videos.
• This manual includes all operating instructions and precautions,
and users must read it carefully and follow the instructions.
• Hover-1 can not be held liable for damage or injury caused by
failure to understand and follow the warnings and instructions in this
manual.
ATTENTION
1. Use only the supplied charger with this scooter.
Charger Manufacturer: DONGGUAN GREEN POWER ONE CO.,
LTD
Model: GA09-4200400US
2. The operating temperature range of the Axle is 32-104° F
(0-40° C).
3. Do not ride on icy or slippery surfaces.
4. Read the user manual and warning labels before riding.
5. Store the Axle in a dry, ventilated environment.
6. When transporting the Axle, avoid violent crashes or impact.
LOW TEMPERATURE WARNING
Low temperature will affect the lubrication of moving parts inside
the Axle scooter, increasing internal resistance. At the same time,
in low temperatures, the discharge capacity and the capacity
itself of the battery will be significantly decreased.
Use caution when riding the Axle in cold temperatures (below 40
degrees F).
Doing so may increase the risk of mechanical failures of the
scooter, which may lead to damage to your Axle, other property
damage, serious bodily injury and even death.
SAFETY INSTRUCTIONS
• Keep the Axle away from heat sources, direct sunlight, humidity,
water and any other liquids.
• Do not operate the Axle if it has been exposed to water,
moisture or any other liquids to prevent against electric shock,
explosion and/or injury to yourself and damage to the Axle.
• Do not use the Axle if it has been dropped or damaged in
any way.
• Repairs to electrical equipment should only be performed by
the manufacturer. Improper repairs voids the warranty and may
place the user at serious risk.
• Do not puncture or harm the exterior surface of the product in
any way.
• Keep the Axle free from dust, lint, etc.
• Do not use this Axle for anything other than its intended use or
purpose. Doing so may damage the Axle or lead to property
damage, injury or death.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries, battery pack, or batteries installed to
excessive heat, such as direct sunlight, or open flame.
• Do not allow hands, feet, hair, body parts, clothing or similar
articles to come in contact with moving parts, wheels or
drivetrain, while the engine is running.
1
WARNING!

PLEASE READ THE USER MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in
the user manual can lead to damage to your Axle, other property
damage, serious bodily injury, and even death.
Thank you for purchasing the Hover-1 Axle Electric Scooter. Please
read all instructions carefully before using and retain this manual for
future use and reference.
This manual applies to the Axle Electric Scooter.
• In order to avoid dangers that are caused by collisions, falls, and
loss of control, please learn how to ride the Axle safely.
• You can learn operating skills by reading the product manual and
watching videos.
• This manual includes all operating instructions and precautions,
and users must read it carefully and follow the instructions.
• Hover-1 can not be held liable for damage or injury caused by
failure to understand and follow the warnings and instructions in this
manual.
ATTENTION
1. Use only the supplied charger with this scooter.
Charger Manufacturer: DONGGUAN GREEN POWER ONE CO.,
LTD
Model: GA09-4200400US
2. The operating temperature range of the Axle is 32-104° F
(0-40° C).
3. Do not ride on icy or slippery surfaces.
4. Read the user manual and warning labels before riding.
5. Store the Axle in a dry, ventilated environment.
6. When transporting the Axle, avoid violent crashes or impact.
LOW TEMPERATURE WARNING
Low temperature will affect the lubrication of moving parts inside
the Axle scooter, increasing internal resistance. At the same time,
in low temperatures, the discharge capacity and the capacity
itself of the battery will be significantly decreased.
Use caution when riding the Axle in cold temperatures (below 40
degrees F).
Doing so may increase the risk of mechanical failures of the
scooter, which may lead to damage to your Axle, other property
damage, serious bodily injury and even death.
SAFETY INSTRUCTIONS
• Keep the Axle away from heat sources, direct sunlight, humidity,
water and any other liquids.
• Do not operate the Axle if it has been exposed to water,
moisture or any other liquids to prevent against electric shock,
explosion and/or injury to yourself and damage to the Axle.
• Do not use the Axle if it has been dropped or damaged in
any way.
• Repairs to electrical equipment should only be performed by
the manufacturer. Improper repairs voids the warranty and may
place the user at serious risk.
• Do not puncture or harm the exterior surface of the product in
any way.
• Keep the Axle free from dust, lint, etc.
• Do not use this Axle for anything other than its intended use or
purpose. Doing so may damage the Axle or lead to property
damage, injury or death.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries, battery pack, or batteries installed to
excessive heat, such as direct sunlight, or open flame.
• Do not allow hands, feet, hair, body parts, clothing or similar
articles to come in contact with moving parts, wheels or
drivetrain, while the engine is running.
2

• Do not operate or allow others to operate the Axle until the user
understands all instructions, warnings and safety features described
in this manual.
• Check with your doctor if you have a medical condition that
could affect your ability to use the Axle.
• Persons with head, back or neck ailments or prior surgeries to
those areas of the body are not recommended to use the Axle.
• Do not operate if you are pregnant, have a heart condition, or
have both.
• Persons with any mental or physical conditions that may make
them susceptible to injury or impair their physical or mental
capabilities to recognize, understand and perform all of the
safety instructions and to be able to assume the hazards inherent
in unit use, should not use the Axle.
In this manual, the above symbol with the word “NOTES” indicates
instructions or relevant facts the user should remember prior to using
the device.
In this manual, the above symbol with the word “CAUTION”
indicates a hazardous situation which, if not avoided, can cause
minor or moderate injury.
In this manual, the above symbol with the word “WARNING”
indicates a hazardous situation which, if not avoided, can cause
death or serious injury.
Please keep the serial number on file for warranty claims as well as
proof of purchase.
WARNING: Prolonged Exposure to UV Rays, Rain and the Elements
May Damage the Enclosure Materials.
Store Indoors When Not in Use.
3
WARNING!
WARNING!
SERIAL NUMBER
CAUTION!
NOTES:

67
OPERATING PRINCIPALS
The Axle uses digital electronic gyroscopes and acceleration sensors
to control balance and motion, depending on the user's center of
gravity. The Axle also uses a control system to drive the motors that
are located within the wheels. The Axle has a built-in inertia dynamic
stabilization system that can help assist with balance when moving
forward and backwards, but not while turning.
TIP – To increase your stability, you must shift your weight in order to
overcome the centrifugal force during turns, especially when
entering a turn at higher speeds.
Model: Hover-1™Axle (H1-AXL)
Net Weight: 14.3 lbs (6.5 kg)
Load: 44-160 lbs (20-72.5 kg)
Max Speed: Up to 7 mph (11.3 km/h)
Max Distance Range: Up to 3 miles (4.8 km)
Max Incline Angle: 10°
Minimum Turning Radius: 0°
Charge Time: Up to 6 hours
Battery Type: Lithium-ion
Battery Voltage: 37 V
Battery Capacity: 2.0Ah
Power Requirement: AC 100-240V, 50/60Hz
Ground Clearance: 1 Inch (2.54 cm)
Platform Height: 4.5 Inches (11.43 cm)
Tire Type: Non-Pneumatic Solid Tires
The Hover-1 Axle is a personal transporter. Our technology and
production processes are developed with strict testing for each Axle
scooter. Operating the Axle without following the contents of this
manual may lead to damage to your Axle or bodily injury.
This manual is designed to give you the information you need for the
safe operation and maintenance of your Axle. Please read it
thoroughly before riding your Axle.
PACKAGE CONTENTS
• Hover-1 Axle Electric Scooter
• Wall Charger
• Operation Manual
FEATURES/PARTS
1. Fender 5. Tire
2. Left Foot Mat 6. Charge Port
3. Battery Indicator 7. Power Button
4. Right Foot Mat 8. Protective Chassis Casing
4
11
55
234
8
INTRODUCTION

OPERATING PRINCIPALS
The Axle uses digital electronic gyroscopes and acceleration sensors
to control balance and motion, depending on the user's center of
gravity. The Axle also uses a control system to drive the motors that
are located within the wheels. The Axle has a built-in inertia dynamic
stabilization system that can help assist with balance when moving
forward and backwards, but not while turning.
TIP – To increase your stability, you must shift your weight in order to
overcome the centrifugal force during turns, especially when
entering a turn at higher speeds.
Model: Hover-1™Axle (H1-AXL)
Net Weight: 14.3 lbs (6.5 kg)
Load: 44-160 lbs (20-72.5 kg)
Max Speed: Up to 7 mph (11.3 km/h)
Max Distance Range: Up to 3 miles (4.8 km)
Max Incline Angle: 10°
Minimum Turning Radius: 0°
Charge Time: Up to 6 hours
Battery Type: Lithium-ion
Battery Voltage: 37 V
Battery Capacity: 2.0Ah
Power Requirement: AC 100-240V, 50/60Hz
Ground Clearance: 1 Inch (2.54 cm)
Platform Height: 4.5 Inches (11.43 cm)
Tire Type: Non-Pneumatic Solid Tires
The Hover-1 Axle is a personal transporter. Our technology and
production processes are developed with strict testing for each Axle
scooter. Operating the Axle without following the contents of this
manual may lead to damage to your Axle or bodily injury.
This manual is designed to give you the information you need for the
safe operation and maintenance of your Axle. Please read it
thoroughly before riding your Axle.
PACKAGE CONTENTS
• Hover-1 Axle Electric Scooter
• Wall Charger
• Operation Manual
FEATURES/PARTS
1. Fender 5. Tire
2. Left Foot Mat 6. Charge Port
3. Battery Indicator 7. Power Button
4. Right Foot Mat 8. Protective Chassis Casing
5
SPECIFICATIONS
WARNING
Any Axle that does not work properly can
cause you to lose control and fall. Inspect
the entire Axle thoroughly before every ride,
and do not ride it until any problems
have been corrected.

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY
TURNING YOUR DEVICE ON/OFF
Power On: Take your Axle out of the box and place it flat on the floor.
Press the power button (located on the rear of your Axle) once.
Check the LED indicator (located in the center of your Axle). The
battery indicator light should be lit, indicating the Axle is powered on.
Power Off: Press the power button once.
MAT SENSOR
There are four sensors under the foot mats on your Axle.
When riding the scooter, you must ensure you are stepping on the
foot mats. Do not step or stand on any other area of your scooter.
The Axle may vibrate or spin in one direction, if weight and pressure
are applied to only one foot mat.
BATTERY INDICATOR
The display board is located in the middle of the Axle.
• Green LED Light indicates the hoverboard is fully charged.
• Red flashing LED light and beeping indicates low battery.
• Yellow light indicates the board is charging.
When the LED light turns red, please recharge the Axle.
RUNNING INDICATOR
When the operator triggers the foot mats, the Running Indicator LED
will light up, which means that the system enters the running state.
When the system has an error during operation, the running LED light
will turn red (for more details see SAFETY ALERTS).
6
CONTROLS AND DISPLAY

It is important that you fully understand all elements of your Axle. If
these elements are not used correctly, you will not have full control
of your Axle. Before you ride, learn the functions of the various
mechanisms on your scooter.
Practice using these elements of your Axle at slower speeds in a flat,
open area before taking the Axle out in public areas.
PRE-RIDE CHECKLIST
Ensure that your Axle is in proper working order each and every time
you ride. If a part of the scooter does not function correctly, please
contact our Customer Support Center.
• Ensure the battery is fully charged before riding your scooter.
• Ensure that the screws on the front and back tires are locked firmly
before each ride.
• Please wear all appropriate safety and protective gear as
previously mentioned in the User Manual before operating your Axle.
• Make sure to wear comfortable clothes and flat closed-toe shoes
when operating your Axle.
• Please carefully read the User Manual, which will assist in
explaining the basic working principles and provide tips on how to
best enjoy your experience.
7
BEFORE RIDING
WARNING
Any Axle that does not work properly
can cause you to lose control and fall.
Do not ride a Axle with a part that is
damaged; replace the damaged part
before riding.

Different localities and countries have different laws governing riding
on public roads, and you should check with local officials to ensure
you are complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not
follow local laws and regulations.
• For your safety, always wear a helmet that meets CPSC or CE
safety standards. In the event of an accident, a helmet can protect
you from serious injury and in some cases, even death.
• Obey all local traffic laws. Obey red and green lights, one-way
streets, stop signs, pedestrian crosswalks, etc.
• Ride with traffic, not against it.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians and alert them if you intend to
pass them from behind.
• Slow down at all street intersections and look to the left and right
before crossing.
Your Axle is not equipped with reflectors. It is not recommended that
you ride in conditions of low visibility.
Think about safety when you ride. You can prevent many
accidents if you think about safety. Below is a helpful checklist for
Compact riders.
8
SAFETY PRECAUTIONS
WARNING
When you ride in low-visibility conditions
such as fog, dusk, or night, you might be
diicult to see, which could lead to a
collision. In addition to keeping your
headlight on, wear bright, reective
clothing when riding in poor lighting
conditions.