Hover-1 RIDER User manual

ELECTRIC SCOOTER
RIDER
OPERATION MANUAL
HY-RIDR

HELMETS
SAVE
LIVES!
Always wear a properly tted helmet that
complies with CPSC or CE safety standards
when you ride your scooter.
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed
and vulnerable to
serious injury.
1

WARNING
As with all mechanical components, the Hover-1
Rider is subjected to wear and high stresses.
Dierent materials and components may react to
wear or fatigue in dierent ways. If the design life of
a component has been exceeded, it may
suddenly fail possibly causing injuries to the rider.
Any form of crack, scratch or change of coloring in
highly stressed areas indicate that the life of the
component has been reached and it should be
replaced. Do not ride in an abusive manner.
In this manual, the CAUTION sign indicates a
hazardous situation which, if not avoided, can cause
minor or moderate injury.
CAUTION
WARNING
In this manual, the WARNING sign indicates a
hazardous situation which, if not avoided, can cause
death or serious injury.
2

This manual is designed to give you the information you need for
the safe operation and maintenance of your Rider. Please read it
thoroughly before riding your Rider.
The Hover-1 Rider is a personal transporter. Our technology and
production processes are developed with strict testing for each
Hover-1 Rider Electric Scooter. Operating the Hover-1 Rider
without following the contents of this manual may lead to
damage to your Hover-1 Rider, or bodily injury.
PACKAGE CONTENTS
• Hover-1 Rider Electric Scooter
• Key with Remote
• Charging Cable
• Operation Manual
• Rear View Mirrors
This item is not a toy. It is not recommended for riders under the
age of 18.
Your Hover-1 Rider's serial number is stamped respectively on
steering column and battery column as shown below. Record
the serial number for your reference.
ATTENTION
Use only the supplied charger with this scooter.
Charger Manufacturer:
JIN XIN YU POWER (SHENZHEN) SUPPLY CO., LTD
Model: XVE126-5840200
WARNING
Make sure you read this complete
manual before riding your Hover-1
Rider. Failure to do so, or failure to
follow its guidelines could lead to
serious injury or death.
INTRODUCTION
3

HOVER-1 RIDER DIAGRAM
12
13
14
15
10
11
9
1
2
7
8
4
5
3
6
1. Rear-view Mirror
2. Throttle
3. Storage Compartment
4. Seat
5. License Plate Holder
6. Shock
7. Front Brake Lever
8. Turn Signal
9. Charge Port
10. Meter Display
11. Rear-view Mirror
12. Rear Brake Lever
13. Basket
14. Headlight
15. Tire
FEATURES/PARTS
4

SPECIFICATIONS
HANDLEBAR DIAGRAM
1. Rear Brake
2. Parking Brake
3. Low Beam/High Beam Switch
4. Meter Display
5. Forward / Reverse Switch
6. Front Brake
7. Turn Signal Switch
8. Horn
9. Ignition
10. Light Switch
11. Horn
12. Speed Adjustment Button
13. Throttle
Model: Hover-1 Rider (HY-RIDR)
Load: 286.6 lbs (129 kg)
Max Speed: Up to 15 mph (24.1 km/h)
Max Distance Range: Up to 27.96 miles (45 km)
Max Incline Angle: 20° degrees
Min. Clearance: 4.72 Inches ( 12 cm)
Brake Type: Front Disk Brake and Rear Drum Brake
Shock Absorption: Front Frame Suspension Fork, Rear Two
Heavy-Duty Shock Absorbers
Hand Height: 37 Inches (93.98cm)
Tire Size: 3 Inches width (7.62cm)
90% Span ratio
10 Inches diameter (25.4cm)
Motor: 500W
Charge Time: Up to 13 hours
Battery Type: Lithium-ion
Battery Voltage: 51.2V
Battery Capacity: 20 Ah
Power Requirement: AC 100-240V, 50/60Hz
NOTE: Max speed and max distance may vary depending on, but not
limited to: user load, terrain of road, operation temperature, driving habits
and environmental temperatures.
5
1246
13
5
9
811 12
10
7
3

CONTROLS & DISPLAY
IGNITION
REMOTE
6
1. SPEEDOMETER
Displays current speed in
mph.
2. TURN SIGNAL
Indicates left or right
turning signal.
3. LIGHT INDICATOR
Indicates if headlights are
on/o.
4. BATTERY LIFE INDICATOR
Displays your remaining
battery life.
1. LOCK
Press once to activate arm.
2. UNLOCK
Press once to disarm alarm.
3. ALARM
Press once to sound alarm.
4. REMOTE START
Press twice to remotely start scooter.
This will work within a 15 foot range
of your scooter.
1. TURNING ON SCOOTER
Turn key clockwise to “START” to
turn on scooter engine.
2. TURNING OFF SCOOTER
To turn scooter o, turn the key to
“OFF.”
3. OPEN SEAT
Turn key to “OPEN” to unlock seat
cover and open.
4. LOCK
Push key in and turn key to “LOCK”
to lock scooter.
11 2
3
4
20 30
40
10
mph
50
0
H L
1
2
3
4

SEAT COMPARTMENT
Your Rider comes with a seat compartment for extra storage
and to house your battery.
To access the seat compartment simply put the key in the
ignition and turn it to “OPEN.”
Beneath the storage area, you will nd the:
1. Main Circuit Breaker
2. Rechargeable Battery Compartment
7
2
1

1. Remove the rear-view mirrors from the box.
2. Attach the rear-view mirrors by screwing the mirrors (with posts) into the
grommets shown in the diagram below.
CHARGING YOUR RIDER
ATTACHING REAR-VIEW MIRRORS
• Locate the charging port underneath the front end of the seat.
• Lift the charging port ap to reveal the charging port.
8

Only use the enclosed charging
cable and charger to charge your
Rider. Using any other unauthorized
charger may damage your Rider.
CAUTION
9
• Make sure that there is no dust, debris or dirt inside the port.
• Locate the charge cable and plug the male end into a
grounded wall outlet.
• Plug the female end in the scooter’s charge port.
• The charging indicator light on your charger should change to
RED, indicating that your device is now being charged.
• When the RED indicator light on your charger turns to GREEN,
then your device is fully charged.
• A full charge may take up to 13 hours.
• After fully charging your scooter, unplug the charge cable from
the power outlet.
• Lift the charge port ap back up and push in to secure it back
into place.