Hovertech HTAIR-2300 User manual

HTAIR®MANUAL
AIR SUPPLY
NO USER SERVICEABLE PARTS.
Only qualified service personnel shall perform repairs on the HoverTech
International Air Supply.
Page 1 2021-10-29

HTAIR®MANUAL
Part Identification
Handle /
Attachment Hook
Dust Cover
Hose Attachment Snap
Air Filter
Air Filter Cover
Hose
Bumpers Power Cord
(US/UK/Euro)
Power Cord
Strap
Foot
Information Labels
Power Cord Clamp
Grounding Pin
Used for a Ground Continuity (Bond) Test.
Circuit Breakers
Metal Cover
Control Panel
Label
Page 2 2021-10-29

HTAIR®MANUAL
Power Cord / Clamp Replacement
Page 3 2021-10-29

HTAIR®MANUAL
Handle Replacement
1. Remove the damaged handle by unscrewing the socket head screw from the barrel
nut using two 5/32” allen wrenches as shown.
2. Attach the new handle by reversing the process. When tightening the screw be sure
that the handle can rotate easily. The screw is treated with thread lock to secure it in
place.
Carrying Handle/
Attachment Hook
5/32” Allen
Wrench
5/32” Allen
Wrench
Socket
Head Screw
Barrel Nut
Page 4 2021-10-29

HTAIR®MANUAL
Feet or Bumper Replacement
Foot
Bumper
1. The feet and bumpers are held in place by a self-adhesive backing. Use a small, flat
bladed screwdriver to pry up an edge and gently remove the foot or bumper.
2. Clean surface thoroughly to remove any excess adhesive that may have been left
behind. Apply the new part by removing the backing material and position as shown.
Press firmly to ensure adhesion.
Page 5 2021-10-29

HTAIR®MANUAL
Hose Removal
1. Remove the damaged hose by lifting the dust cover slightly and unsnapping the hose
from the side of the unit as shown.
2. Push the release button at the top of the unit to remove the hose.
3. Attach the new hose by reversing the process.
Hose Release Button
Dust Cover
Hose Attach-
ment Snap
Hose
Page 6 2021-10-29

HTAIR®MANUAL
Air Filter and Air Filter Cover Replacement
1. Disconnect hose from unit.
2. Remove the two phillips head screws on each side to detach the air filter covers.
3. Re-attach the new air filter covers and screws.
1. Follow the steps shown above to remove air
filter covers.
2. Remove air filters and replace.
3. Re-attach the air filter covers and screws.
To Remove Air Filter Covers
To Remove Air Filters
Air Filter
Air Filter Cover
Page 7 2021-10-29

HTAIR®MANUAL
1
2
3
Dust Cover
Snap Replacement Detail
Dust Cover/Hose Attachment Snap Replacement
1. Disconnect hose from unit.
2. Lift the cover “flap” to remove the 3 phillips head screws that attach the dust cover.
3. To replace dust cover, fold in the three flexible tabs. Then insert the screws one at a
time starting with the top middle followed by the sides.
1. Disconnect hose from unit.
2. Remove the phillips head screw and snap.
To Remove Dust Cover
To Remove Hose Attachment Snap
Page 8 2021-10-29

HTAIR®MANUAL
Metal Cover Replacement
1. Disconnect hose from unit.
2. Remove the two phillips head screws on each side to detach the air filter covers.
Remove the air filters.
3. Gently pull the damaged
cover apart to allow clearance to remove it.
4. Carefully re-insert the new metal cover.
Reassemble the two filters and filter covers.
5. Secure everything in place by reinserting
four screws.
Air Filter
Air Filter Cover
Metal Cover
Page 9 2021-10-29

HTAIR®MANUAL
Cord Strap Replacement
1. Unsnap the strap and remove power cord.
2. Detach the damaged cord strap by removing the screw as shown.
3. Reattach strap by positioning in place and securing it with the screw provided.
Power Cord Strap
Page 10 2021-10-29