HP f650x User manual

f650x
Car Camcorder
User Manual

1
Contents
Regulatory notices............................................................................... 3
Prohibition of co-location.................................................................... 3
WEEE Notice......................................................................................... 3
CE Regulatory Notice ........................................................................... 4
Notes on Installation ........................................................................... 4
Caution ................................................................................................ 4
1 Introduction..........................................................................7
1.1 Features................................................................................... 7
1.2 Package Contents .................................................................... 7
1.3 Product Overview..................................................................... 8
2 Getting Started .....................................................................9
2.1 Storage Media.......................................................................... 9
2.1.1 Insert the Memory Card ............................................... 9
2.1.2 Remove the Memory Card............................................ 9
2.2 Installing in Vehicles .............................................................. 10
2.2.1 Mount to Windshield .................................................. 10
2.2.2 Adjust the Camcorder................................................. 11
2.3 Connecting to Power.............................................................. 12
2.4 LED Indicator.......................................................................... 12
2.5 Powering the Camcorder On / Off .......................................... 13
2.5.1 Auto Power On/Off..................................................... 13
2.5.2 Manual Power On/Off................................................. 13
2.5.3 Reset .......................................................................... 13
2.6 Initial Settings........................................................................ 14
2.6.1 Set Time Zone ............................................................ 14
2.6.2 Set the Date / Time .................................................... 15
3 Using the Car Camcorder ......................................................16
3.1 Automatic Record .................................................................. 16

2
3.1.1 The Recording Screen................................................. 17
3.1.2 Emergency Recording ................................................ 19
3.2 Add Speed Point..................................................................... 19
3.3 Picture in Video...................................................................... 20
3.4 Driving Safety ........................................................................ 20
3.4.1 Speed Cam Alert......................................................... 21
3.4.2 Speed Limit Alert........................................................ 22
3.4.3 Driver Fatigue Alert .................................................... 23
3.4.4 LDWS.......................................................................... 23
3.4.5 FCWS .......................................................................... 25
3.4.6 Headlight Warning ..................................................... 26
3.7 Playback Videos and Photos.................................................. 31
3.8 The Playback Screen.............................................................. 32
3.9 Deleting Files ......................................................................... 33
4 Initial set up Go Dashcam application ...................................34
5 Using the Go Dashcam application........................................36
5.1 Camera preview, record, snapshot ........................................ 37
5.2 Playback, delete, download................................................... 38
5.3 Local album ........................................................................... 40
5.4 Camera Setting ...................................................................... 41
6 Adjusting the Settings .........................................................42
6.1 Using the Menu ...................................................................... 42
6.2 Menu Items ............................................................................ 42
7 Installing the Software........................................................47
8 SuperCar.............................................................................48
9 Specifications .....................................................................49

3
About this Guide
The content in this document is for information purpose and is subject to
change without prior notice. We have made every effort to ensure that
this User Guide is accurate and complete.
However, no liability is assumed for any errors or omissions that may
have occurred.
The manufacturer reserves the right to change the technical
specifications without prior notice.
Regulatory notices
This document provides country- and region-specific non-wireless and
wireless regulatory notices and compliance information for your product.
Some of these notices may not apply to your product.
Prohibition of co-location
This device and its antenna(s) must not be co-located or operated in conjunction
with any other antenna or transmitter.
WEEE Notice
Disposal of Waste Electrical and Electronic Equipment and/or Battery
by users in private households in the European Union
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of
materials will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health
and environment.

4
CE Regulatory Notice
The product herewith complies with the requirements of the Low Voltage
Directive 2014/35/EU, the EMC Directive 2014/30/EU, the RED-Directive
2014/53/EU and the RoHS Directive 2011/65/EU.
EU Health Protection: This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Notes on Installation
1. Please measure the front windshield viewing area, make sure not to
block driver's front view, install the camcorder below the rearview
mirror (the central, higher right position of the front windshield). And
we recommend that the sky and the land occupied by the screen
50%, fix the car holder and then adjust the camcorder so that the
lane is aligned with the screen. Proper installation enables the
camcorder to maximize the efficiency also can enhance the accuracy
of LDWS.
2. Make sure that the lens is within the wiping range of the windscreen
wiper to ensure a clear view even when it rains.
3. Do not touch the lens with your fingers. Finger grease may be left on
the lens and will result in unclear videos or pictures. Clean the lens
on a regular basis.
4. Do not install the camcorder on a tinted window. Doing so may
damage the tint film.
5. Make sure that the installation position is not hindered by the tinted
window.
6. This product is suitable for light windshield or light color
heat-resistant film windows , it will affect video quality if install it on
the dark windows or dark heat-resistant film windows.
7. Use the products of the attached power charger only, please do not
use other brand power charger, in order to avoid equipment burn or
cause the battery explosion.
Caution
Due to local laws and vehicles safety considerations, do not
operate the camcorder while driving.
Set up time zone, time and date accurately before you use this
camcorder.
Please use SuperCar software under the condition that Electronic
Map are functioning normally.

5
The firmware function in the camcorder is for reference only,
drivers are advised to exercise discretion based on actual road
conditions.
The results of GPS positioning are only for reference, and should
not affect the actual driving situation. The camcorder also cannot
ensure the positioning accuracy.
GPS positioning accuracy may differ depending on weather and
location such as high buildings, tunnels, undergrounds, or forests.
GPS satellite signals cannot pass through solid materials (except
glass). Tinted window will also affect the performance of the GPS
satellite reception.
GPS reception performance on each camcorder may differ. The
camcorder cannot determine the accuracy of the positioning results
from different hardware.
The values displayed in this camcorder, such as speed and
position, may be inaccurate due to the influence of surrounding
environment. They are for your reference only.
This product is used only for non-commercial use, within the
maximum limits permitted by applicable law. We do not take any
responsibilities for the loss of use of the product.
This camcorder gets warm when in use; this is normal.
Improper use or operation of the product may result in damage of
the product or its accessories and void the warranty.
Wi-Fi Signals are unable to pass through the building. The upper
limit of signal transmission is 5m.
Wi-Fi Operation Channel: Ch1~Ch13
The product employs wireless data communication which may
interfere, or be interfered by, a near-by camcorder.
Never use this camcorder in the vicinity of a microwave oven or at
places where there is radio interference.
Radio wave reception may be worsened in specific environments.
Please be advised that if another camcorder is also using the same
2.4GHz band as this product, the processing speed of both
camcorders may slow down.
This product gets warm when in use; this is normal.
Improper use or operation of the product may result in damage of
the product or its accessories and void the warranty.
The radio frequency (RF) generated by this RF electronic camcorder
may cause adverse effects on the operation of other electronic

6
camcorders and result in malfunctioning. Wireless transmitters and
circuitry may also interfere with other electronic camcorders.
Therefore, do observe the following precautions:
Aircraft: Never use a radio transmitter when you are in an
airplane. Please switch off the Wi-Fi function of the
camcorder.
Vehicle: The radio frequency transmitted by this camcorder
may affect the electronic system in a motorized vehicle.
Please consult the manufacturer or dealer of your vehicle on
the possible effect.
Pacemaker: In order to prevent any potential interference to a
pacemaker, anyone who uses a pacemaker should be advised,
that, when using this camcorder, a minimum distance of 15cm
(6 inch) should be kept between the camcorder and the
pacemaker; and never put this camcorder in a chest pocket. In
case of any doubt of interference, switch off the camcorder
immediately.
Medical Camcorder: If you use a personal medical camcorder,
consult the camcorder manufacturer or your physician to
confirm if your camcorder is sufficiently shielded from the RF
transmission of this camcorder.
Medical Facilities: Hospitals and medical institutes may use
facilities that are sensitive to an external RF energy. Observe
such instructions when the medical care personnel or any
posted sign requests you to switch off any camcorder that
may interfere the radio frequency.
Explosion sites or any location with a posted sign: In order to
prevent interfering with an explosion activity, observe all the
signage and instructions in the Explosion Area or in a zone
with a “Switch Off 2-way Radios” sign by switching off
camcorders that may interfere with the radio frequency.
HP Inc. is NOT responsible for the loss of any data/content during
operation.
Before you start using the system, it is assumed that you
agree to the above statement.

7
1Introduction
Thank you for purchasing this advanced Car Camcorder. This product is
specifically designed for real time video recording when driving.
1.1 Features
Full HD 1920*1080
2.0" TFT-LCD color screen
150° Wide angle lens
Collision Detection, when a collision is detected, the camcorder will
automatically trigger the emergency recording
Parking Mode
Multifunction traffic safety reminder
1.2 Package Contents
The package contains the following items. In case there is any missing or
damaged item, contact your dealer immediately.
Car camcorder
Electrostatic
sticker
CD-ROM
Quick start guide
Car charger

8
1.3 Product Overview
No.
Item
No.
Item
1
LED Indicator
8
Speaker
2
LCD Color Screen
9
Wide Angle Lens
3
Menu / Back Button ( / )
10
Microphone
4
Playback / Up Button ( / )
11
Power Button
5
Snapshot / Down Button ( / )
12
Power Connector Port
6
Emergency Recording / Confirm
Button ( / )
13
Memory Card Slot
14
Bracket Knob
7
Voice Record on/off ( )
Note:
Please press the button (3~7) according to the diagram notice shown on screen.

9
2Getting Started
2.1 Storage Media
2.1.1 Insert the Memory Card
Insert memory card with the pins facing forward and the screen of the
camcorder facing forward too, see the picture as below:
2.1.2 Remove the Memory Card
If the camcorder is power on, please power off first and wait for the
procedure of switching off the camcorder completed before removing
the memory card.
Note:
1. Do not remove or insert the memory card when the camcorder is turned on. This may damage the
memory card.
2. Support SDHC class 10 and memory storage 8GB or above (support up to 32GB).
3. Please format the micro SD cards before the initial use. The formatted file type for this camcorder
is FAT32 file.
4. Periodically format the microSD card (recommended period: once a month).

10
2.2 Installing in Vehicles
2.2.1 Mount to Windshield
1. Put the electrostatic sticker onto the suggested area on the
windshield. Before putting the sticker, please wipe and clean the
windshield. During the installation, please make sure the bubbles
in between the sticker and the window are all gone.
2. Peel off the protective plastic sheet from the adhesive pad.

11
3. Place and press the bracket firmly onto the electrostatic sticker on
the windshield window. Make sure the base is securely locked in
place.
2.2.2 Adjust the Camcorder
1. Loosen the knob to swivel the camcorder to adjust view angle.
2. Then tighten the knob to make sure the camcorder is securely
locked in place.

12
2.3 Connecting to Power
Use only the supplied car charger to power up the camcorder.
1. Connect one end of the car charger to the USB connector of the
camcorder. USB port input: DC 5V / 1A.
2. Plug the other end of the car charger to the cigarette lighter socket
of your vehicle. Once the vehicle engine is started, the camcorder
automatically powers on. Car charger input: DC 12 / 24V.
2.4 LED Indicator
Status Explanation
LED Indicator Color
Power off, connect
external power
Red
Power on, standby
Green
Recording/ Recording
and screen off
Flash red

13
2.5 Powering the Camcorder On / Off
2.5.1 Auto Power On/Off
Start the car engine, wait a few seconds to charge the camcorder, and
then screen will light up and the camcorder will automatically power on
and start recording.
Once the vehicle engine shuts down, the camcorder automatically saves
the recording and turns off the power.
2.5.2 Manual Power On/Off
To manually turn on the power, press the POWER button.
To turn off, press and hold the POWER button for at least 2 seconds.
2.5.3 Reset
Press and hold the Power button for 8 seconds to reset the device.

14
2.6 Initial Settings
Before using the camcorder, we recommend you setup the correct Time
zone, Date and Time.
Note:
Please note that ifyou press the button during recording, the system will stoprecording and
enter OSD menu. Make sure the recording is already stopped then continue operating the menu.
2.6.1 Set Time Zone
To set the time zone, do the following:
1. Press the button to enter the OSD menu.
2. Press the or button to select Set Time Zone, and then
press the button for entering function menu.
3. Press the or button to set the current time zone, and
then press the button to complete setting.
4. Press the button to return to recording screen.
Note:
1. If Time Sync. is on, camcorder clock will be calibrated via satellite clock signal based on Set Time
zone.
2. If satellite positioning is not successful, camcorder clock will run based on user defined time.

15
2.6.2 Set the Date / Time
To set the correct date and time, do the following:
1. Press the button to
enter the OSD menu.
2. Press the or
button to select Date / Time,
and then press the
button for entering function
menu.
3. Press the or
button to adjust the value, and then press the button to set
the next field.
4. Repeat step 3 until the date and time setting is completed.
Note:
To ensure the accuracy of the video file time, please reset the date and time when not inuse over 7
days.

16
3Using the Car Camcorder
3.1 Automatic Record
Start the car engine, wait a few seconds to charge the camcorder, and
then screen will light up and the camcorder will automatically power on
and start recording.
Recording will automatically stop when the engine is switched off.
Note:
1. Some vehicle power supply would not turn on / off automatically with the car engine start, if the
camcorder cannot automatically power on/off with the car engine, please manually connect the
power supply with the vehicle power, and then power on, or manually power off the camcorder and
then release the connector with the car power supply.
2. It can be configured to save a videofile for every 30 seconds, 1 or 3 minutes of recording.
3. All the videos and photos are saved in the memory card, if memory card is full, loop recording will
generally overwrite the oldest video file.
4. The camcorder is built-in super capacitor. After start the car engine, please waita few seconds for
charging the camcorder, and then the camcorder will automatically power on and start recording.

17
3.1.1 The Recording Screen
No.
Icon
Item
Description
1
Recording Duration
Indicates the video current duration.
2
Date / Time
Indicates the current recording date
and time.
3
Menu Button
During video recording, press the
button to enter the OSD menu.
4
Add Speed Point
Button
During video recording, press the
button to add a speed cam
point.
5
PIV (Picture in
Video) Button
Press to capture video screen
shots from the front camera.
6
Emergency
Recording Button
During video recording, press the
button to enter emergency
recording mode.

18
7
Voice Record on/off
Turn on/off voice recording.
8
Resolution
icon
Indicates the video resolution.
9
Voice Record
icon
Indicates voice recording sets as off,
the sound will not be recorded.
10
Satellite Positioning
icon
Indicates the strength of satellite
positioning. If the icon shows in red
on screen, it indicates that the
camcorder cannot complete the
satellite positioning.
11
Power icon
Indicates camcorder is connected
with power.
12
Wi-Fi
Wi-Fi on
Wi-Fi off

19
3.1.2 Emergency Recording
To Start the Emergency Recording, do the following:
1. During Video Recording, press
the button to enter
emergency recording mode,
the “Emergency” message
will be shown immediately on
the upper left corner of the
screen, and the recorded file
will be protected.
2. The emergency video
recording length is same as the recording interval setting. When the
emergency recording length reaches the setting, the system will
return to the general recording mode.
Note:
1. If the Collision Detection function is enabled and a collision is detected, the camcorder will
automatically trigger the emergency recording.
2. The emergency file is created as a new file and saved in Emergency folder, which will be protected
to avoid being overwritten by normal loop recording. The Emergency folder will occupy 40%of
available memory card capacity. For example, ifyou use 8GB memory card, about 3.2GB memory
space will be saved for emergency files. When the Emergency folder is full, the oldest emergency file
will be automatically deleted by the newest emergency file.
3.2 Add Speed Point
You may customize speed cam positions in this product.
1. When the GPS positioning is completed , press to update speed
camera points.
2. This product features a capacity of 50 speed cam positions. In case
you are trying to add more than that, the system prompts with
message "Speed Position is full".
Note:
You may delete custom speed cam positions by selecting the Delete Last Position or Delete All
Position option from the Speed Position Management menu. Please note that all of your existing
speed cam positions are deleted once the Delete All Position option is selected. Make sure you are
ready to recreate your custom speed cam positions before running this option.