Huawei FusionModule1000A20 Technical specifications

FusionModule1000A20 Prefabricated All-in-One
Data Center
V200R003C10
Product Description (380 V)
Issue
01
Date
2019-10-31
HUAWEI TECHNOLOGIES CO., LTD.

Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
https://e.huawei.com

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
About This Document
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes the FusionModule1000A 20ft prefabricated all-in-one data center
solution (pre-fab. module for short) for the CT scenario in terms of its overview, typical
application scenarios, product architecture, and key technical specifications, helping readers
to systematically understand the FusionModule1000A20.
Intended Audience
This document is intended for:
⚫Sales engineers
⚫Technical support engineers
⚫System engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Remarks
Indicates an imminently hazardous situation
which, if not avoided, will result in serious
injury or death.
Indicates a potentially hazardous situation
which, if not avoided, could result in serious
injury or death.
Indicates a potentially hazardous situation
which, if not avoided, may result in minor
or moderate injury.
Indicates a potentially hazardous situation
which, if not avoided, could result in
equipment damage, data loss, performance
deterioration, or unanticipated results.
NOTICE is used to address practices not
related to personal injury.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
About This Document
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Remarks
Calls attention to important information,
best practices and tips.
NOTE is used to address information not
related to personal injury, equipment
damage, and environment deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all the
changes made in earlier issues.
Issue 01(2019-07-15)
This issue is the first official release.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
Contents
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document ............................................................................................................... ii
1 Overview ................................................................................................................................... 1
1.1 Positioning............................................................................................................................................................ 1
1.2 Features................................................................................................................................................................. 2
1.3 Standards Compliance........................................................................................................................................... 3
2 Typical Application Scenarios and Typical Configuration................................................ 5
2.1 Typical Application Scenarios................................................................................................................................ 5
2.2 Typical Configurations........................................................................................................................................... 7
2.3 Key System Technical Specifications..................................................................................................................... 7
3 System Architecture............................................................................................................... 11
3.1 Pre-fab. Module Structural System........................................................................................................................11
3.1.1 Pre-fab. Module.................................................................................................................................................11
3.1.2 Thermal Insulation Structure..............................................................................................................................13
3.1.3 Pre-fab. Module Door........................................................................................................................................14
3.1.4 Pre-fab. Module Interior Layout.........................................................................................................................15
3.1.5 Mesh Cable Tray ...............................................................................................................................................18
3.1.6 Pre-fab. Module Exterior Ports...........................................................................................................................18
3.2 Power Supply and Distribution System .................................................................................................................19
3.2.1 Overview...........................................................................................................................................................19
3.2.2 PDF (MCCB Input)...........................................................................................................................................25
3.2.3 PDF (ATS Input) ...............................................................................................................................................26
3.2.4 AC/DC Power System (TP48400B-N20B3) .......................................................................................................28
3.2.5 AC/DC Power System (TP48600B-N20B1) .......................................................................................................30
3.2.6 AC/DC Power System (TP481200B-N20B1)......................................................................................................32
3.2.7 Battery ..............................................................................................................................................................33
3.3 Cooling System....................................................................................................................................................34
3.3.1 Overview...........................................................................................................................................................34
3.3.2 3 kW Intelligent Heat Exchanger........................................................................................................................36
3.3.3 5 kW Intelligent Heat Exchanger........................................................................................................................37
3.3.4 13.5 kW Fresh Air Integrated Unit .....................................................................................................................37
3.3.5 (Optional) Dehumidifier ....................................................................................................................................38
3.4 Management System.............................................................................................................................................38

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
Contents
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
v
3.4.1 Overview...........................................................................................................................................................38
3.4.2 ECC800.............................................................................................................................................................42
3.4.2.1 Product Configuration.....................................................................................................................................42
3.4.2.2 Main Control Module .....................................................................................................................................47
3.4.2.3 Power Module ................................................................................................................................................51
3.4.3 Smart ETH Gateway..........................................................................................................................................51
3.4.4 ETH Converter..................................................................................................................................................53
3.4.5 T/H Sensor (BOM number: 02310NBS).............................................................................................................55
3.4.6 Access Actuator.................................................................................................................................................56
3.4.7 Network Camera (02352QPS)............................................................................................................................59
3.5 Fire Extinguishing System....................................................................................................................................61
3.5.1 Overview...........................................................................................................................................................61
3.5.2 (Optional) Extinguishant Control Panel..............................................................................................................63
3.5.3 (Optional) Heptafluoropropane Fire Extinguisher...............................................................................................64
3.5.4 (Optional) ASD .................................................................................................................................................66
3.5.5 (Optional) Photoelectric Smoke Detector ...........................................................................................................67
3.6 Surge Protection and Grounding ...........................................................................................................................68
3.6.1 Surge Protection ................................................................................................................................................68
3.6.2 Grounding.........................................................................................................................................................68
3.7 Integrated Cabling................................................................................................................................................70
4 Acronyms and Abbreviations............................................................................................... 72

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
1 Overview
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
1
1 Overview
1.1 Positioning
Huawei has developed the FusionModule1000, a green data center solution, based on a
thorough study on the reform and impact of the cloud computing to traditional data centers
and the practical experience of dozens of global cloud computing centers. The solution
features a flexible, hybrid, and modular design to help customers construct green
infrastructure adapting to cloud computing.
The FusionModule1000, foundation for cloud computing in enterprise data centers, integrates
power distribution, monitoring, cooling, racks, cable routing, and fire extinguishing. It is
characterized by good waterproof and quakeproof performances. The FusionModule1000
helps enterprise telecom operators and Internet operators to rapidly deploy data centers and
has unique advantages in the fields of disaster relief, military affairs, oil exploitation, survey,
and enterprise data for its availability in outdoor environments.
The FusionModule1000, located at the bottom layer of a data center, provides basic physical
construction for all services in the data center.
Figure 1-1 Data center architecture

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
1 Overview
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
2
1.2 Features
The FusionModule1000A is a small-capacity prefabricated all-in-one data center that
integrates the pre-fab. module mechanical structure, power supply and distribution system,
cooling system, management system, fire extinguishing system, and integrated cabling system.
It features high security and reliability, rapid deployment, low costs, high efficiency, and
intelligent management.
Security and Reliability
⚫The pre-fab. module is properly grounded and resists electromagnetic interference. Its
electromagnetic compatibility (EMC) meets class A requirements specified in the
CISPR22/EN55022 standard.
⚫The data center uses International Organization for Standardization (ISO) standard 668
pre-fab. modules that provide IP65 protection (IP55 by default; IP65 available by
changing the dustproof module at the air vent) as they are assembled by industry-leading
welding technologies and well sealed to be waterproof and dustproof.
⚫Thanks to special coating for the pre-fab. modules, the pre-fab. modules pass the
1440-hour UL salt spray test, equivalent to a service life longer than 25 years. Based on
corrosion definitions in ISO12944-2 and service life evaluation rules in ISO12944-1, a
720-hour salt spray test in the C4-high environment is equivalent to more than 15 years
of service life, and the 1440-hour salt spray test is equivalent to 25 years of service life.
⚫The bullet-proof function can be provided for the pre-fab. modules if required. The
pre-fab. modules pass the 10 m rifle test as they are armed with 4.2 mm bullet-proof steel
plates on their sides and 2.4 mm bullet-proof steel plates on the top.
⚫The pre-fab. modules meet the operating requirements of the ambient temperature
ranging from –20°C to +55°C.
⚫The pre-fab. modules meet NEBS zone 3 antiseismic requirements.
⚫The intelligent access control system and mechanical locks provide multifold security
protection and meets class 3 theftproof requirements in EN 1627–EN 1630 or other
standards.
⚫Optional: The fire extinguishing system is reliable, clean, insulating, and
environment-friendly, and can put out a fire efficiently and safely without damaging
equipment, thereby ensuring high equipment availability. The extinguishing agent is
Heptafluoropropane. The CE version complies with the EU's CE certification.
The fire extinguishing system in standard configuration uses manual fire extinguishing.
Rapid Deployment
⚫Streamlined manufacturing, professional division of labor, and good work conditions
ensure that modules and products of the FusionModule1000Aare produced efficiently
with strict quality control. The standard product manufacturing period is less than four to
six weeks.
⚫Infrastructure equipment such as cooling equipment, power supply equipment, and racks
are factory-installed. The customer needs only to provide network cables, power cables,
and water pipes onsite for commissioning.
⚫System commissioning is completed in factories, and therefore onsite engineering and
equipment room commissioning take less than one week.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
1 Overview
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
3
⚫The pre-fab. modules can be easily migrated as it can be transported on level-3 roads and
applies to various scenarios such as dynamic data service deployment, military affairs
application, disaster relief, and field operations.
Cost-Effectiveness and High Energy Efficiency
⚫One pre-fab. module integrates the cooling system, power distribution system,
monitoring system, fire extinguishing system, and security system that are installed and
pre-commissioned before delivery. The FusionModule1000A goes through the trial run
before delivery. You are welcome to check and try the product in factory.
⚫Civil engineering is simple when the FusionModule1000A is deployed outdoors. The
FusionModule1000A starts to work after it is installed on a concrete column or podium
and connects to the humidifier, water, mains supply, and networks.
⚫Mature delivery mode, modular structure, and low transportation costs of the pre-fab.
modules ensure fast deployment of the FusionModule1000A, and simple and convenient
expansion and upgrade.
⚫The energy efficiency and cooling efficiency are high.
Intelligent Management
⚫Centrally manages all infrastructures of the data center equipment room.
⚫O&M using the mobile app and remote unattended operations are available. Full WiFi
coverage is implemented inside the pre-fab. modules using a WiFi converter. WiFi
coverage outside the pre-fab. modules is implemented using a customer router gateway
(optional).
⚫Monitors equipment efficiently in real time.
⚫Monitors the environment in real time to identify potential risks.
⚫Robust security management:A robust security mechanism is ready to protect equipment
and ensure a secure environment.
⚫Standard network management system (NMS) interface: The management system
provides Simple Network Management Protocol (SNMP) interfaces to communicate
with third-party NMSs.
1.3 Standards Compliance
Table 1-1 Standards compliance
Standard Code
Standard Name
TIA-942-2012
Telecommunications Infrastructure Standard for Data Centers
NOTE
GB 50174-2017: Electronic Information System Equipment Room
Design Specifications
IEEE 1100-2005
Recommended Practice for Powering and Grounding
Electronic Equipment
IEC60364-5-52
Low-voltage electrical installations
IEC_60044-1
Current Transformers

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
1 Overview
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
4
Standard Code
Standard Name
EN 61000-4-11-2004
Testing and measurement techniques-Voltage dips, short
interruptions and voltage variations immunity tests
EN 61439-1
Low-voltage Switchgear and Controlgear Assemblies
ASHRAE TC 9.9
Thermal Guidelines for Data Processing
Environments-Expanded Data Center Classes and Usage
Guidance
NFPA 72_2013
National Fire Alarm and Signaling Code
NFPA75
Standard for the protection of information technology
equipment
NFPA2001
Standard on Clean Agent Fire Extinguishing Systems
UL_2755
OUTLINE OF INVESTIGATION FOR MODULAR DATA
CENTERS
BS EN 15004
Fixed firefighting systems. Gas extinguishing systems
BS EN 54
Fire detection and fire alarm systems
BS EN 12094
Fixed firefighting systems _ Components for gas
extinguishing systems
BS 6266_2011
Fire protection for electronic equipment installations
BS 5839-1-2002
Fire detection and fire alarm systems for buildings
BS ISO 14520-1-2006
Gaseous fire-extinguishing systems
BS EN 1363_2012
Fire resistance tests
ISO 668:1995
Series 1 freight container-Classification, dimensions and
ratings
ISO 1161:1984
Series 1 freight container-Corner fittings-Specification, MOD
ISO 6346:1995
Freight container-Coding, identification and marking
TIA 942
Telecommunications Infrastructure Standard for Data Centers
IEC60297
Dimensions of mechanical structures of the 482.6 mm (19 in )
series
GR-63-CORE
NEBS Requirements: Physical Protection
BS EN1363-1: 2012
Fire-resistance tests - Part 1: General requirements
IEC 60529:2013
Degrees of protection provided by enclosures (IP Code)
ISO 7253
Paints and varnishes - Determination of resistance to neutral
salt Spray (fog), 2nd edition 1996-12-25
ISO 12944-6
Paints and varnishes - Corrosion protection of steel structures
by protective paint systems Part 6: Laboratory performance
test methods 1st edition 1998-05-15

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
5
2 Typical Application Scenarios and Typical
Configuration
2.1 Typical Application Scenarios
The FusionModule1000 is applicable to fast deployment of outdoor small-sized CT
equipment rooms for carriers. It can integrate standard and nonstandard mainstream CT
equipment, and can be easily relocated.
Table 2-1 Typical application scenarios of the FusionModule1000
Wireless Site Equipment
Room
Fixed Network
Convergence Site
Equipment Room
Submarine Cable
Landing Site
⚫Based on the cloud radio
access network (C-RAN)
architecture, battery
backup units (BBU) and
other devices are
centralized to implement
BBU coordination for
equipment room at the
edge site.
⚫High power (3 kW or
higher), long backup
power (≥ 4 hours), and
various cabinet types
(N63, N66, and N68)
⚫An equipment room at
the CO site is
responsible for access of
optical transmission
network terminals and
for metro aggregation
network transmission.
⚫Small power (less than 1
kW), N63 is mainly used
as a cabinet, and there is
no mandatory
requirement for the
backup time.
⚫The equipment room is
used for land connection
of submarine optical
cables.
⚫N63 is mainly used as a
cabinet, long backup
power (≥ 4 hours), and
applicable to class C
environment
Distributed and mobile single-enclosure deployment applies to equipment room construction
or modernization.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
6
Figure 2-1 Mobile application scenario
The FusionModule1000 cannot be transported with the CT equipment, power modules, and batteries.
The FusionModule1000 is the first choice when a data center needs to be quickly constructed
and deployed due to urgent service requirements.
The FusionModule1000 supports distributed single-enclosure deployment in outdoor areas
such as wilderness, mining areas, and deserts to meet application requirements of the harsh
environment.
Figure 2-2 Application in harsh outdoor environments

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
7
2.2 Typical Configurations
Table 2-2 Typical configurations
Category
System Components
Structural
system
⚫There is no raised floor or CT cabinets (user-supplied). The
supported CT cabinet dimensions (H x W x D) are 2200 mm x 600
mm x 800 mm, 2200 mm x 600 mm x 600 mm, and 2200 mm x 600
mm x 300 mm.
⚫Cables and terminals for connecting the AC/DC power system to
CT cabinets are not configured.
Power supply
and distribution
system
PDF (MCCB input and ATS input), AC/DC power system
(TP48400B-N20B3 and TP48600B-N20B1 and TP481200B-N20B1),
and battery (150 Ah and 190 Ah and 1000 Ah)
Cooling system
Intelligent heat exchanger (3 kW and 5 kW), Fresh air integrated unit
(13.5 kW)
Monitoring
system
ECC800, DC power module, smart ETH gateway, ETH converter,
camera, SD card, T/H sensor, smoke sensor, access actuator,
single-door magnetic lock, exit button, IC card reader, and IC card
Fire
extingui
shing
system
Manu
al fire
exting
uishin
g
Emergency light, exit indicator, and hand-held fire extinguisher
(purchased locally)
CE
autom
atic
fire
exting
uishin
g
(optio
nal)
Photoelectric smoke detector, heat detector, fire alarm bell, fire alarm
horn/strobe, emergency light, exit indicator, extinguishant control
panel, external fire alarm horn/strobe, emergency shutdown button, gas
release indicator, electrical actuator, pneumatic switch, nozzle, fire
cylinder, and ASD
2.3 Key System Technical Specifications
Table 2-3 Key technical specifications
Item
Specifications
System BOM number
21262910
21262910-001
21262910-002
21262910-003
21262911
Power
supply
and
distribu
Power input
One 160 A
input,
three-phase
four-wire+PE,
Two 250 A
inputs,
three-phase
four-wire+PE,
One 160 A
input,
three-phase
four-wire+PE,
Two 250 A
inputs,
three-phase
four-wire+PE,
Two 250 A
inputs,
three-phase
four-wire +

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
8
Item
Specifications
tion
380 V AC/400
V AC/415 V
AC, 50/60 Hz
380 V AC/400
V AC/415 V
AC, 50/60 Hz
380 V AC/400
V AC/415 V
AC, 50/60 Hz
380 V AC/400
V AC/415 V
AC, 50/60 Hz
PE, 380 V
AC/400 V
AC/415 V
AC, 50
Hz/60 Hz
Surge
protection
level
Level 3 surge protection, nominal 20 kA (8/20 µs), maximum 40 kA (8/20 µs)
Supported
device
power
N+X scenario:
≤ 8 kW
2N scenario: ≤
8 kW
N+X scenario:
≤ 16 kW
2N scenario: ≤
16 kW
2N scenario:
≤ 24 kW
Backup
time
N+X scenario:
2 hours (in the
initial state)
2N scenario: 6
hours (in the
initial state)
N+X scenario:
1 hour (in the
initial state)
2N scenario: 3
hours (in the
initial state)
N+X
scenario: 3
hours (in the
initial state)
Coolin
g
Cooling
capacity
8 kW (3+1 redundancy)
16 kW (4+1 redundancy)
24 kW (2+1
redundancy)
Refrigerant
R134a
R134a
Temperatur
e control
range
18°C to 30°C
18°C to
30°C
Fire
extingu
ishing
Type
Manual fire extinguishing in standard configuration, and automatic fire extinguishing
in the CE version.
Alarm
(Optional) Automatic monitoring and detection, and the fire alarm horn/strobe is
supported.
Detection
(Optional) Gas is released when dual alarm conditions are met.
Extinguisha
nt
(Optional) Heptafluropropane.
Monito
ring
IP camera
Dual-resolution IP cameras installed at the main entrance door
Managemen
t function
Monitors the internal temperature, humidity control system, fire detection and control
system, access control system, cooling system, and power distribution system in real
time.
O&M using the mobile APP, remote unattended control
(Optional) Supports monitoring over emails and Simple Network Management
Protocol (SNMP) short messages.
All backup power sources are connected over programable dry contacts or fast
Ethernet (FE) ports.
Structu
re
Dimensions
(H x W x
D)
20ft standard ISO shipping pre-fab. module: 2896 mm x 2438 mm x 6058 mm
Thermal
Overall heat transfer coefficient of the pre-fab. module ≤ 0.59 W/(m2K)

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
9
Item
Specifications
insulation
Fireproof
performanc
e
The pre-fab. module interior is decorated with B1 fire-resistant materials, and the
enclosure structure uses the 50 mm A1 fire-resistant rock wool material, providing a
fire resistance duration of 15 minutes. Requirements for higher fire resistance can be
met by customization, which will change the pre-fab. module and its interior structure.
NOTE
The pre-fab. module exterior can be protected with customized fireproof panels, which can
provide a fire resistance duration of 120 minutes as tested by the UL lab based on BS EN
1364-1:1999 and BS EN 1363-1:2012 standards.
(Optional)
Integrated
cabling
The integrated cabling solution needs to be provided for project customization.
IP rating
(Optional) IP55/IP65
Installation
mode
Directly installed on the ground
NOTE
The pre-fab. module can also be installed on a concrete platform, with four 300 mm high steel
bases connected to the concrete platform using M16 bolts.
Weight
Preinstallation weight before delivery: ≤ 7500 kg; maximum load bearing capacity: ≤
10,000 kg
Cabinet
specificatio
ns
N63 cabinet: 600 x 300 x 2200 mm (air intake from front and air exhaust from top)
N66 cabinet: 600 x 600 x 2200 mm (air intake from front and rear, air exhaust from
top)
N68 cabinet: 600 x 800 x 2200 mm (air intake from front and air exhaust at rear)
Enviro
nmenta
l
require
ments
Ambient
temperature
–20°C to +55°C
NOTE
T ≤ 35°C: not derated. The maximum load rate decreases by 7.5% each time when the temperature
increases by 5°C.
Storage
temperature
–40 to +70°C
Ambient
humidity
5%–95% RH
Environmen
t corrosion
requirement
s
Class C environments, more than 500 m away from the seashore
Altitude
Maximum altitude: 3000 m (derated when the altitude > 1000 m)
⚫Altitude ≤ 1000 m: not derated. Working at an altitude of less than 1000 m, and
low pressure scenario are satisfied.
⚫When the altitude exceeds 1000 m, the power of each 1000 m is derated by 5%.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
2 Typical Application Scenarios and Typical
Configuration
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
10
⚫Do not leave the prefabricated data center power off for more than six months. If the data
center will be idle for a long time, power it on and keep it operational for at least two
hours every six months.
⚫The battery storage temperature ranges from –20°C to +40°C.
⚫Batteries can be stored without power-on for a maximum of 90 days. If the storage period
exceeds 90 days, recharge the batteries promptly.

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
3 System Architecture
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
11
3 System Architecture
3.1 Pre-fab. Module Structural System
3.1.1 Pre-fab. Module
Figure 3-1 Appearance 1 (8 kWand 16 kW)
(1) External horn strobe
(optional)
(2) Air exhaust
window
(3) Fire control box
(optional)
(4) Card reader
(5) Main entrance door
(6) Intelligent heat exchanger

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
3 System Architecture
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
12
Figure 3-2 Appearance 2 (8 kWand 16 kW)
(1) Feeder window
(2) Air intake window
(3) Ground point
Figure 3-3 Appearance 1 (24 kW)
(1) External horn strobe (optional)
(2) Fire control box (optional)
(3) Card reader

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
3 System Architecture
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
13
(4) Main entrance door
(5) Fresh air integrated unit
Figure 3-4 Appearance 2 (24 kW)
(1) Feeder window
(2) Air intake window
(3) Ground point
3.1.2 Thermal Insulation Structure
The pre-fab. module is furnished with a thermal insulation layer composed of rock wool
(density: 120 kg/m3), and color steel plates.
Figure 3-5 Thermal insulation structure

FusionModule1000A20 Prefabricated All-in-One Data
Center
Product Description (380 V)
3 System Architecture
Issue 01 (2019-10-31)
Copyright © Huawei Technologies Co., Ltd.
14
3.1.3 Pre-fab. Module Door
Figure 3-6 Appearance
Table 3-1 Main entrance door technical specifications
Item
Specifications
Width
1100 mm
Net width
950mm
Height
2420 mm
IP rating
IPX5
Theftproof
Class 3 (Optional)
Door opening angle
≥ 120°, the door closer is configured.
Bearing capacity
When the door is open, the door, door
frame, and mechanical parts can withstand
the door weight and will not deform
permanently within 48 hours with a static
load of 15 kg at any part.
Waterproof structure
The fireproof door uses rubber strips with a
framework and composite adhesive to