Huawei E600 User manual

i
Contents
Getting E600 Ready...................................................................1
Installation Guide.......................................................................1
Introduction to the E600 Manager Interface..............................2
Internet Service..........................................................................2
Call Service................................................................................2
SMS Service...............................................................................4
Contacts Service.........................................................................4
Call Register Service..................................................................5

1
Welcome to use the HUAWEI E600 Data Card.
With the E600, you can easily access the:
yInternet service
yCall service
ySMS service
yContacts service
yCall Register service
Getting E600 Ready
Please insert the SIM card into the slot according to
the direction arrow on the back of the E600 with the
golden contact point downward and the blunt corner
inwards.
Installation Guide
The installation procedures of the E600 Manager may
be somewhat different under different operating
systems (Windows XP and Windows 2000). Please
refer to the actual installing tips if the installing
description is different from the following. Here, we
will take the Windows XP operating system as an
example.
1. Installing the E600 Manager
1) Put the disk that contains the E600 Manager into
the CD-ROM drive of your computer.
2) The installation procedures will start
automatically. If the auto-run program does not
start, go to the drive path, find the Setup.exe file
and double click on it, and then the program is
running.
3) When the Choose Language dialog box appears,
select the installation language correspondingly,
and click <OK>.
4) Do according to the instructions of the setup
program.
5) After successful installation, a shortcut for the
E600 will be seen on the desktop.
2. Installing the E600 Driver
1) Insert the E600 which contains the SIM
(Subscriber Identity Module) card into the
PCMCIA slot of the computer.
2) Now the system will automatically find the new
hardware and automatically initialize the new
hardware Installation Shield Wizard.
3) If a prompt such as "The software failed to pass
the Logo Test" appears, please click <Continue
Anyway> to continue the installation.
4) When the installation is over, click <Finish> to
complete the installation.

2
3. Removing the E600
Note: To remove the E600, please use the hardware
deleting function of the Windows system to stop
the operation of the E600 and then pull it out.
1) Double click on the lower right corner of the
computer screen; the "Safely Remove Hardware"
window will be displayed.
2) Stop the use of the E600 hardware "NEC PCI to
USB Open Host Controller".
3) When the system prompts you that it is safe to
remove the device, pull out the E600.
Introduction to the E600 Manager Interface
1. Entering the E600 Manager Interface
Double click on the desktop to start the E600
Manager. If the system prompts you to input a PIN
(Personal Identity Number), please input a correct one.
2. Shortcut Icons Description
/: Connecting from/Disconnecting to the
network.
: Opening the default Internet browser in the
operating system.
: Accessing the Call service.
: Accessing the SMS (Short Message Service)
service.
: Accessing the Contacts service.
: Accessing the Call Register service.
Internet Service
1. Network Connection Settings
Creating a New Profile:
1) Select Settings ––> Network Connection Settings
on the menu bar.
2) Click <New>.
3) Enter a new profile name and other parameters.
4) Click <Save> to save the new profile.
Note: Please contact your network operator to get the
parameters and the values.
2. Accessing the Internet
1) Click to connect the network.
2) When the connection is completed, corresponding
information about the connected network will be
displayed on the right side of the window, which
includes:
yHaving connected time of the current connection;
yThe data flow volume of the current connection;
yThe volume, rate and the top rate of the current
sending and received data.
3) Click to open the Browser.
4) Click to disconnect the network.
Call Service
Insert an earphone into the earphone jack of the E600
before a call service.

3
1. Making a Call by Directly Entering a
Telephone Number
1) Click to open the Call Service window.
2) You may enter a telephone number:
yWith the keyboard; or
yBy clicking telephone keypad on the Call Service
window.
3) Click to make a call.
4) Click to hang up.
Note: You may click to cancel the input
number digit by digit or to cancel the whole input
number by clicking and holding down it for a
moment. Alternatively, you may also do it by
pressing the Backspace key of the computer
keyboard.
2. Making a Call by Choosing a Telephone
Number from the Contacts List
1) Click to go to the Call Service window.
2) Click to open the Contacts list. Double
click a contact or select a contact and then click
<Call>:
yIf the contact you have selected has only one number,
this number will appear on the window and be dialed
out directly.
yIf the contact has two or more numbers, double click
the intended number from the pop-up Select Phone
Number window or click <OK> after selecting the
number; and the selected number will appear on the
window and be dialed out directly.
3) Click to hang up.
3. Making a Call by Selecting a Recently Dialed
Number
1) Click to go to the Call Service window.
2) Click to display a list of 10 recently dialed
numbers. Double click the intended telephone
number or click <Call> after selecting the number,
then the number will be dialed out directly.
3) Click to hang up.
4. Answering a call
The E600 may prompt you an incoming call by sound
or vision. You may select Settings––> Options to set
the prompt mode for incoming calls.
yThe E600 provides a sound prompt mode. You will
hear a sound on an incoming call.
1) Click to enter the Call Service window.
2) Click to answer a call.
3) Click to hang up.
yYou will see a pop-up window on an incoming call if
you have enabled "Display alerts when a call
coming".
Click <Answer> to answer a call.
Click <Reject> to reject a call.

4
5. Volume Control
Click to open the Call Service window. You may
adjust the voice volume by pressing or .
yPress to increase the volume;
yPress to decrease the volume.
SMS Service
1. Writing a New SMS Message
1) Click to open the SMS Service window.
2) Click <Write> to open a New SMS window.
3) Enter a telephone number and SMS contents.
4) Click <Send> to send the message.
Note: You may also click <Contacts> to search for a
telephone number in the Contacts book.
2. Viewing an SMS Message
An incoming SMS message can be prompted by sound
or vision as is preset on the menu bar Settings––>
Options.
yYou will hear sound prompt on a new incoming SMS
message if you have enabled "Play a sound when a
message is received".
1) Click to enter the SMS window.
2) Click <Inbox> to enter the inbox to view received
SMS messages.
yYou will see a pop-up window on a new incoming
SMS message if you have enabled "Display alerts
when a message is received".
Click <View> on the pop-up window to enter the
Inbox to read SMS messages, or click <Close> to
overlook SMS messages.
3. SMS settings
Select Settings ––> SMS Settings, the SMS settings
window will be displayed:
yRequest status report: With this function being
enabled, the network will send you a report once the
receiver has received an SMS message.
yUse same SMS centre for reply: Set the SMS center
number which receivers used to reply messages to the
same one as the sender.
ySMS Bear: The bearer field that is used to send SMS
messages: if Packet Switched (PS) is enabled,
messages are sent through the packet field; if Circuit
Switched (CS) is enabled, messages are sent through
the circuit field.
yValidity: Select the valid period during which SMS
messages can be stored in the SMS center.
yCurrent SMS centre: The E600 will read the number
of the current SMS centre. If no such information or
it has been accidentally deleted, please contact your
card provider to get this number.
Contacts Service
1. Creating a New Item in the Contacts
1) Click to enter the Contacts window.
2) Click <New>.
3) Enter such information as Name, telephone
numbers, e-Mail and other information.
4) Click <Save> to save the information.

5
2. Modifying Items in the Contacts
1) Click to enter the Contacts window.
2) Highlight the information to be modified and
double click it or click <Edit>.
3) Click <Save> to save the modified information.
3. Deleting Items from the Contacts
1) Click to open the Contacts window.
2) Select one or more items you want to remove
from the contacts, and then click <Delete>.
3) Click <OK> to confirm the deletion.
4. Sending a Message
1) Click to open the Contacts window.
2) Select one or more items from the Contacts, a
dialog box of "Please select number" will pop up.
3) Select one or more numbers you want to send, and
then click <OK>; the program will jump to the
window for creating a new message.
Note: If the item you have selected contains only one
telephone number, the window for creating a new
message will be displayed automatically.
4) The mobile numbers retrieved appear in the blank
column behind the "Contacts". Input the content
for the message and click <Send>.
5. Making a Call
1) Click to open the Contacts window.
2) Select the item that contains the number you want
to dial from the Contacts, and then click <Call>.
yIf the item you have selected contains only one
telephone number, the Call Service window will be
displayed automatically.
yIf two or more telephone numbers are contained in
the item you have selected, the Select Phone Number
window will be displayed and you will be prompted
to select one number. After doing that, click <OK>
and the Call Service window will be displayed.
3) The phone number you have selected will be
displayed automatically in the Call Service
window; and the number will be dialed out
automatically.
6. Searching for Items in the Contacts
1) Click <Find>.
2) In the Search window:
ySelect a field item from the pull-down list in the
"Condition" area.
yEnter relevant searching terms in the "Value" text
box.
yChoose "Whole word only" and/or "Case sensitive"
for "Matching Type".
3) Click <Next> or <Prev> to begin searching.
Call Register Service
The call register service provides the information of
missed calls, received calls and dialled calls.
The executable operations and operating procedures
for these items of service are absolutely the same. Now
let's take the operations for the Missed Calls service as
an example for introduction.

6
1. Sending a Message
1) Click to open the Call Register window.
2) Click <Missed calls> to access the registered
missed calls.
3) Select one or more items, a dialog box of "Please
select number" will pop up.
4) Select one or more numbers you want to send, and
then click <OK>; the program will jump to the
window for creating a new message.
Note: If the item you have selected contains only one
telephone number, the window for creating a new
message will be displayed automatically.
5) The mobile numbers retrieved appear in the blank
column behind the "Contacts". Input the content
for the message and click <Send>.
2. Making a Call
1) Click to open the Call Register window.
2) Click <Missed calls> to access the registered
missed calls.
3) Select an item and click <Call>.
4) The selected phone number will be displayed
automatically on the window, and then the
number will be dialed out automatically.
3. Saving a Number
1) Click to open the Call Register window.
2) Click <Missed calls> to open the item of missed
calls.
3) Select an item and click <Get Number>, the
program will jump to the New Contacts window.
4) By default, the E600 will save the number of this
item to the Mobile column in the contacts.
5) Click <Save> to save the number.
4. Deleting Items
1) Click to open the Call Register window.
2) Click <Missed calls> to access the Missed calls
window.
3) Select one or more items.
4) Click <Delete>. If you are sure, click
<OK>.
Ver: V1.11 BOM: 31014924