Huawei PowerCube 500 PC500-300H1 User manual

1
Issue: 03
Date: 2018-03-22
PowerCube 500 V200R001C10 Quick Guide
(PC500-300H1, PC500-300G1)
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
1 Overview
Function module: PC500-300H1,
PC500-300G1
Lithium battery: CBM20E-N14A1
Appearance Grid Hybrid Scenario Solar Hybrid Scenario
Lightning rod
PMP
microwave
Bullet
cameras
Dome
camera
Cantilever
Pole
mounting kit
Pole
mounting kit
Function
module Lithium battery
Lithium battery
Pole
Lithium battery
Lithium battery
Function
module
Pole
mounting kit
Pole
mounting kit
Bullet
cameras
Dome camera
Lightning rod
PV modules
PV module
support
Pole
Cantilever
PMP
microwave
Lithium
Battery
Indicator
Color
Status
Meaning
Run
indicator
(RUN)
Green
Off
The lithium battery has no power input
or is faulty.
Steady on
The lithium battery is powered on.
Blinking
slowly
(0.5 Hz)
The lithium battery is communicating
properly with upstream monitoring
equipment.
Blinking
fast (4 Hz)
The lithium battery fails to
communicate with upstream
monitoring equipment.
Alarm
indicator
(ALM)
Red
Off
There is no alarm.
Steady on
The lithium battery has generated a
fault alarm and needs to be replaced.
Blinking
slowly
(0.5 Hz)
The lithium battery has generated a
protection alarm, which can be cleared.
Function
Module
Indicator
Color
Status
Meaning
Run
indicator
Green
Off
The function module has no power input
or is faulty.
Blinking
slowly
(0.5 Hz)
The function module is communicating
properly with upstream monitoring
equipment.
Blinking
fast (4
Hz)
The function module fails to
communicate with upstream monitoring
equipment.
Alarm
indicator
Yellow
Off
There is no alarm.
Blinking
slowly
The function module has generated an
alarm, which can be cleared.
Steady
on
The function module has generated an
AC power failure or PV array fault alarm,
which can be cleared.
Fault
indicator
Red
Off
The function module is normal.
Blinking
slowly
The function module has an external
fault, which can be cleared.
Steady
on
The function module has an internal fault,
which cannot be cleared.
NOTE
The three indicators are steady on when the power unit of the
function module is upgrading. They return to normal status after the
upgrade is complete.

2
2 Tools
3 Routing Cables Through the Pole
1. Place the pole on a wooden case or a similar object.
2. Route a pull wire.
3. Route cables.
Routing Cables Through
the Grid Hybrid Pole Mains AC cable, module ground
cable, optical fiber, camera cable,
and PMP microwave cables
Camera signal cable,
power cable, and
alarm cable
PMP microwave cables
Module
ground cable
Mains AC cable
and optical fiber
Bullet camera signal
cable, power cable,
and ground cable
Dome camera signal cable,
power cable, alarm cable, and
ground cable
Routing Cables Through
the Cantilever
Camera
ground cable
Routing Cables Through
the Solar Hybrid Pole
Mains AC
cable and
optical fiber
Module
ground cable
Mains AC cable, module
ground cable, optical fiber,
camera cable, PMP microwave
cables, and PV cable
Camera signal cable,
power cable, and
alarm cable
PV DC input cable
PMP microwave cables
PMP microwave cables can be used only in scenarios
where the PMP microwave is adopted.
The cables routed from the pole cable hole have a
length of 1.5 m reserved. The cables routed from the
cantilever cable hole have a length of 0.5 m reserved.
The object where the pole is placed should be able to
bear a load above 700 kg.
NOTE

3
4 Installing a Cantilever
5 Installing Cameras and Cables
Installing Cameras
5.1For the camera installation method, see the camera document.
Installing Camera Cables
5.2
For the cable connections at the camera side, see the camera document. Reserve the other ends of cables.
6 (Optional) Installing the PMP Microwave
For the PMP microwave installation method, see the PMP microwave product document.
7 Installing PV Modules and Cables (Solar Hybrid Scenario)
1. Remove the connective kit, adjust the PV module direction based on the
PV module direction principles, and then reinstall the connective kit. 2. Install the PV module support.
3. Adjust the tilt angle of the PV
module support based on the
site latitude.
4. Loosen the bolt at the
base of the PV module
support.
5. Install the angle adjustment bracket and
tighten the bolt at the base of the PV module
support.
or
or
or
In the northern hemisphere, PV modules face due south. In the southern hemisphere, PV modules face due north.
NOTICE
Site
Latitude
PV
Module
Tilt
Angle
0–15°
15°
16–25°
25°
26–30°
35°
31–45°
45°

4
6. Install horizontal beams. 7. Install two PV modules.
8. Install raking strut beams for the PV modules. 10.Tighten the bolts at the horizontal
beams and raking strut beams.
11.Install raking struts for the PV modules. 12.Install PV cables.
Adhesive
tape
Spacing shim
9. Install spacing shims for the
PV modules.
Spacing shim
Raking
strut beam
Keep the slots of horizontal beams facing
inwards for installing PV modules.
Partially tighten the bolts so that PV modules
can be adjusted during installation.
NOTE
Ensure that the junction boxes on the
rear of PV modules are positioned
consistently.
NOTE
Ensure that the openings of the raking
strut beams face outwards.
Partially tighten the bolts to prevent the
PV modules from sliding.
NOTE

5
Installing the Function Module and Lithium Battery on a Pole
9.1
9 Installing the Function Module and Lithium Battery
8 Installing an Antenna Fastener and Lightning Rod
Solar Hybrid Scenario
Grid Hybrid Scenario
Site
Latitude
Lightning Rod
Tilt Angle
0–15°
15°
16–25°
25°
26–30°
35°
31–45°
45°
Adjust the tilt angle of the lightning
rod based on the site latitude.
Wear gloves during installation.
Do not place a module with its bottom against the ground.
Never install a module with power on. Ensure that the angle between a module and the line vertical to the ground is within 10 degrees.
The paint on the module exterior should be intact. If paint has flaked off, repaint the area to avoid corrosion.
NOTICE
1. Use a positioning
sticker to mark the
installation position for
the pole mounting kit.
2. Install the pole
mounting kit.
Positioning
sticker
Cable hole
Ensure that the arrow on the top of the pole mounting kit points exactly to the middle
point on the top of the positioning sticker.
There are three types of bolts available for installing the pole mounting kit. Choose
the appropriate type of bolts based on the pole diameter.
NOTE
Bolt
(190 mm)
Bolt (120 mm) Bolt (160 mm)
Pole Diameter
(105–140 mm) Pole Diameter (140–175 mm) Pole Diameter (175–210 mm)

6
(Optional) Installing the Function Module and Lithium Battery on a Wall
9.2
Unit: mm
3. Install the function module
hanging kit. 4. Install a function module. 5. Install the lithium battery hanging kit.
6. Install a lithium battery.
If two lithium
batteries are required,
install one above the
other. Install the pole
mounting kit after
using a positioning
sticker at the cable
hole in the upper part
of the pole to mark its
installation position.
For the method, see
steps 1 and 2.
7. (Optional) Install the second lithium battery.
The option to
install a lithium
battery
depends on
the scenario.
No lithium
battery is
required in the
grid-only
scenario.
NOTE
NOTE
The wall must be made of reinforced concrete and be able to bear at least 800 N. The wall must not be damaged if subject to a tension of
1.25 kN exerted outwards vertical to the wall.
NOTICE
Space Planning Installation Procedure
1. Remove wall mounting kits A and B.
Wall mounting
kit A
Wall mounting
kit B

7
2. Mark mounting holes. 3. Drill holes and install bolts in the holes.
4. Install wall mounting kits B. 5. Install wall mounting kits A.
6. Install the function module
hanging kit. 7. Install a function module onto the wall. 8. Install the lithium battery hanging kit.
Level
Marker
One wall mounting kit A and one wall mounting
kit B are used for each module. Determine the
number of wall mounting kits based on the
number of modules to be installed.
NOTE
Unit: mm
Hammer drill
The option to install a lithium battery
depends on the scenario. No lithium battery
is required in the grid-only scenario.
NOTE
Unit: mm

8
Installing Ground Cables for Modules
10.1
10 Installing Cables
Installing Cables for the Maintenance Compartment
10.2
If two lithium batteries are
required, install them onto two
adjacent wall hanging kits.
NOTE
9. Install a lithium battery onto the wall. 10.(Optional) Install the second
lithium battery onto the wall.
Route inter-device cables through the pole.
NOTE
Module ground cable
1. Connect ground cables between the function module and lithium batteries. 2. Connect the other end of the module
ground cable to the pole ground bar.
Pole ground bar
Function module Lithium battery Lithium battery
No.
Cable Hole Silk Screen
Cable Type
Cable Outer
Diameter
1
GE1 - GE2
Optical fiber
6.8±0.3 mm
2
GE3/P&E(++) - GE7 /P&E(++)
P&E network cable
3
GE8/DI
-
4
DO
Dome camera alarm
linkage cable
5
12VDC
Bullet camera power cable
9.3±0.4 mm
6
24VAC
Dome camera power cable
Cable Hole Diameter Requirements

9
1. Push up the sunshade
until the spring fastener
is stuck gently.
2. Open the maintenance
compartment. 3. Install cables for P&E cameras.
6. (Optional) Install the door status sensor. 7. (Optional) Install the dome camera alarm linkage cable.
Dome camera
alarm cable
Installation Procedure
Cables for the dome
camera can only be
connected to the
P&E(++) ports.
Bullet camera 1 Bullet camera 2
Bullet camera 3
Dome camera
NOTE
4. (Optional) Install signal cables for non-P&E cameras.
Bullet camera 1 Bullet camera 2
Bullet camera 3
Dome camera
5. (Optional) Install power cables for non-P&E cameras.
Bullet camera 1
Bullet camera 2
Bullet camera 3
Dome camera
Cable distribution terminal
The power cable for the dome camera can only be connected to
the 24VAC port.
Use waterproof tape to protect the cable distribution terminal
and put it inside the pole.
NOTICE

10
Battery cable terminal
AC input, PV input cable terminal
Preparing Cable Terminals
11.3
8. Install optical fibers. 9. Close the maintenance compartment door.
10.Push down the
sunshade until
the spring
fastener is stuck
gently.
Optical network
This figure uses single-ring networking as an example.
NOTE
NOTE
PV input cables can only be used in scenarios with solar energy.
PV input cables and battery cables are finished cables. You only need to strip the cables and then insert them into the cable terminals.
AC input cables need to be prepared onsite. Multi-core cables must be used; otherwise, waterproof connectors may be exposed to water
leakage.
Before assembling cables with waterproof connectors, ensure that the connections between the cables and terminals are secure and reliable.
Negative (blue)
Positive (red)
PE (green)
N/L2 (blue)
L/L1 (brown)
Cable Type
Core Cross-
Sectional Area
Cable Outer
Diameter
Battery cable (2-core)
3.3–6 mm2
9.0–14.5 mm
PV input cable (2-core)
1.5–4 mm2
AC input cable (3-core)
1.5–4 mm2
Scale line
Preparing Battery Cables and Connecting Waterproof Connectors
Flat-head
screwdriver
Preparing PV Input Cables and Connecting Waterproof Connectors
Flat-head
screwdriver Scale line
NOTE
Before closing the maintenance compartment
door, check that cables are properly installed.
After closing the door, press the left side of the
maintenance compartment door by hand and
tighten the screws.

11
Installing Power Cables and Signal Cables
10.4
Preparing AC Input Cables and Connecting Waterproof Connectors
(Unit: mm)
Flat-head
screwdriver Scale line
Installing an RJ45 Communications Cable for a Lithium Battery
Ensure that caps and waterproof connectors are installed at all idle ports on the modules.
NOTICE
Connecting Cables Between the Function Module and Lithium Batteries
PV input
AC input
Function module Lithium battery Lithium battery

12
11 Installing Cable Covers
Installing a Cable Cover for the Function Module
11.1
Install a Cable Cover for the Lithium Battery
11.2
12Erecting the Pole
1. Check whether the pole needs to be repainted. Repaint the damaged area of
the pole, and then use the crane to hoist the pole to the foundation. 2. Secure the pole to the foundation.
Erecting the Mains Pole

13
14 Power-On Commissioning
13 Verifying the Installation
1. Check the indicators on the function module and lithium batteries. Ensure that the green indicators are blinking slowly and that the
yellow and red indicators are off.
2. If a problem is found, refer to the alarm definitions in the user manual for troubleshooting.
3. Observe the board indicators in the maintenance compartment.
1. Check whether the pole needs to be repainted. Repaint the damaged area of
the pole, and then use the crane to hoist the pole to the foundation. 2. Secure the pole to the foundation.
Powering On Modules
14.1
Logging In to the Web Server
14.2
Normally, The STAT, PWR,
and WIFI indicators on the
EG8P panel are: green.
1. Use a mobile phone or laptop to search for devices by
searching for WIFI. (Set the laptop to automatically obtain
IP, even after the WIFI will automatically assign an IP
address.)
Changing an NE ID
14.3
1. Choose Configuration > NE Attribute from the Function Tree.
2. Enter the name of the NE in the Name field.
3. Click “Apply”.
Erecting the Solar Hybrid Pole
NOTE
Default network element IP address: 192.168.1.1.
The Default user name: szhw. Default password: Changeme_123.
NOTE
1. Check that the mounting kits are securely installed and all screws are tightened.
2. Check that all cables are reliably connected with correct polarity and there is no short circuit.
3. Check whether any screw holes are not installed with screws. If so, install screws at the holes.
4. Check that all idle cable holes in modules are protected with waterproof caps.
2. Use the browser to enter the network element default IP,
Enter the Web Server login interface, Enter the values of
“User Name”, “Password”, and “Verification Code”.
3. Click “Login”.
NOTE
The Default WIFI
name: RMn-******.
Default password:
Modify_123.

14
Changing the NE IP Address
14.4
1. Choose Communication > Communication Parameters from the Function Tree.
2. Configure the communication parameters of the NE.
3. Click Refresh.
During site commissioning, the IP address of the gateway NE needs to be configured in compliance with the external DCN requirements but
other non-gateway NEs use IP addresses that are automatically generated based on NE IDs.
Commissioning Cameras
14.5
Commissioning PMP Microwave
14.6
For the camera commissioning method, see the camera document.
For the PMP microwave commissioning method, see the PMP microwave document.
Checking Alarms
14.7
1. Choose Configuration > Browse Current Alarms from the Function Tree.
2. Check the displayed alarm information.
NOTE
Do not use the default NE IP address to access the public network (such as Internet).
The default NE IP address is a temporary address, and is only used for management DCN plug-and-play. The IP address must be
modified in a timely manner.
Huawei Technologies Co., Ltd.
Huawei Industrial Base, Bantian, Longgang
Shenzhen 518129 People's Republic of China
www.huawei.com