Huawei AP6010DN-AGN User manual

HUAWEI TECHNOLOGIES CO., LTD.
AP6010DN-AGN Wireless LAN Access Point
Quick Start Guide

Huawei Technologies Co., Ltd.
Address: Administration Building,Huawei Technologies Co.,
Ltd.,Bantian,Longgang District,Shenzhen,People’s Republic of China
Postcode: 518129
Website: http://www.huawei.com
Email: [email protected]
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of
Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or
part of the products, services and features described in this document may not be within the purchase scope or the usage
scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document
do not constitute the warranty of any kind, express or implied.
1

Change History
Changes between document issues are cumulative. Therefore，the latest document issue contains all the
Changes in previous issues.
Change in Issue 01 (2012-05-30)
Initial commercial release.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
NOTE
CAUTION Indicates a potentially hazardous situation, which if not avoided, could
result in equipment damage, data loss, performance degradation, or
unexpected results.
Provides additional information to emphasize or supplement important
points of the main text.
2

Please download the detailed product documents from "http://support.huawei.com/support/".
The dEtaIled path is as follows: Technical Support->Documentation->Access Network -> WLAN ->WLAN -> Product
Documentation ->AP6010DN.
AP6010DN-AGN
Quick Start Guide
Before performing Installation, confirm that the installation accessories and tools are available.
Installation accessories: Technical Support
Huawei Technologies Co., Ltd.
Address:Administration Building,Huawei
Technologies Co., Ltd.,Bantian,Longgang
District,Shenzhen,People’s Republic of
China
Postcode:518129
Email:[email protected]
Website:http://www.huawei.com
Flat-head
screwdriver
Device Overview
Indicator and Interfaces
Unpack the equipment. Ensure that all items listed in the package list are included in the shipment. If any item is missing,
contact the supplier.
Front view
1
2
3
4
5
1
Item Quantity Unit
AP device
Sheetmetal wall-mounting bracket
6
Quick Start Guide (including the printed
packing list)
Power adapter（Optional）
7
81
Warranty card
Certificate of Conformance
Packing List
Expansion
bolt
Sheetmetal
wall-mounting
bracket
Expansion bolt
Toxic or Hazardous Substance & Elements
Declaration
1
Installation tools:
Phillips
screwdriver
Maker
Wire
stripper
Utility knife
Cable
cutter RJ45
Crimping tool
Combination
pliers Diagonal pliers
ESD
gloves COAX
crimping tool
Adjustable
wrench
Measuring
tape
Hammer
drill Multimeter
Hammer
Level
Vacuum
cleaner Network
Cable tester
1
1
3
1
1
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
Item Quantity Unit
Indicators
1
2 3 4 5
3
2
3
4
5Connected to the maintenance terminal.
Connected to a PoE power supply or switch, or
connected to the Ethernet.
Description
No. Name
DC 12V
Console
ETH/PoE
Default
Connected to the power adapter.
1Indicator For details about indicator, see the Power-on.
Perspective
Press and hold down the Reset button for 3 seconds
to restore the factory settings and restart the AP.
6mm drill
bit

Installing the AP
Select an appropriate installation position and leave 20 cm space above and around the device for cooling air circulation.
AP6010DN dimensions (unit: mm) without a backplane support Recommended AP6010DN installation space (unit: mm)
The AP6010DN can be installed onto a workbench or mounted against a wall. In addition, the AP6010DN can be mounted
to a T-rail and mounted against the ceiling.
Wall-mount the AP6010DN using the plastic wall-mounting bracket:
180
180
50
Field
strength
场强示意
Field
strength
场强示意
1. Fix the wall-mounting bracket to the wall, adjust the
installation position, and use the marker to mark the drilling
positions where expansion bolts are installed.
2. Use #6 drill bit to drill 25-30 mm deep holes in the
drilling positions. Hammer the expansion tubes into
the holes until the expansion tubes are embedded into
the wall.
3. Fix the wall-mounting bracket to the wall, use the
Phillips screwdriver to fasten three self-tapping screws
into the expansion tube.
4. Align the holes at the rear side of the AP with the
hooks on the bracket and hang the AP on the bracket.
Hold the AP with one hand and press the AP
downwards with another hand to secure the AP on the
wall.
59mm
85mm
Underfloor
cabling
4

Installing the AP
Ceiling-mount the AP6010DN using the sheetmetal wall-mounting bracket:
1. Remove the ceiling, determine locations of mounting holes based on the distance between two installation holes,
use the hammer drill to drill holes, and fix the wall-mounting bracket to the ceiling.
2. Align the cucurbit holes at the rear side of the AP with four screws on the wall-mounting bracket and secure the AP.
Adjustable
buckle
Ceiling
M4*30 screw
35mm
Adjustable buckle
Ceiling
Wall-mounting
bracket
Ensure that the AP is correctly installed on the wall-mounting bracket and there must be 20 cm space above and around
the AP for cooling air circulation.
Mounting the AP6010DN to the T-rail using the sheetmetal wall-mounting bracket:
2. Align the cucurbit holes at the rear side of the AP with
four screws on the wall-mounting bracket and secure the
AP.
T-rail Adjustable buckle
1. Use screws to fix the adjustable buckle to the wall-
mounting bracket, hook the adjustable buckle to the T-
rail, and secure the screw on the adjustable buckle to
fasten the wall-mounting bracket and T-rail.
NOTE
To prevent unauthorized personnel from moving the AP, lock the AP using the security lock and determine the position
for installing the security lock. When the sheetmetal wall-mounting bracket is used, fasten the security lock to the wall-
mounting bracket or other immovable object. The following figure shows the security lock. The carrier should purchase
the security lock.
Lock hole
Security lock
M3*6 screw
CAUTION
5

If the AP needs to connect to the Ethernet, ensure that the Ethernet cable is working
properly. If the Ethernet cable is not working properly, for example, RJ45 connectors are short-
circuited, the AP may fail to be powered on or fail to work. Before connecting an Ethernet cable
to the AP, use the cable test tool to check whether the cable is qualified. If the cable is
unqualified, replace it.
1
2
Description
No. Item
Power
adapter 12 V
DC
Network
cable
●The AP6010DN supports PoE power supply and DC power supply.
●When both the PoE power supply and DC power supply are available, the DC power
supply is used.
●When DC power supply is used, use the specified power adapter; otherwise, the device may
be damaged.
Connecting Cables
Requirements for making a network cable:
● Cut the cable of proper length based on the distance between the AP and the PSE device, peel the insulation on
both ends of the network cable, and crimp the wires to RJ45 connectors.
●Connect RT45 connectors to the network cable tester to test cable connectivity. The following shows the pin
assignment.
●The service network cable cannot be connected to the console port. Otherwise, the AP6010DN may be damaged
when using PoE power supply.
●Before connecting the cable to the AP, coil the cable around the wall-mounting bracket first. This prevents the cable
from being bent.
CAUTION
X1 Pin
1
2
3
4
5
6
7
8
X2 Pin
1
2
3
4
5
6
7
8
Wire Color
White and orange
Orange
White and green
Blue
White and blue
Green
White and brown
Brown
6
Connect the network cable to the AP

Power on the AP6010DN and check the indicator status to determine the
System running status.
NOTE
Power-on
Color Frequency Description
Type
Green
Green
0.5 Hz
Default status
Running
Steady on
The system is running properly, the Ethernet connection is
correct,and STAs are associated with the AP.
UBOOT:
The AP is just powered on.
Green
Red Steady on
0.2 Hz The system is running properly, the Ethernet connection is
correct, no user is connected, and the system is in low power
consumption state.
Alarm 4 Hz 1. The AP is being upgraded.
2. The CAPWAP tunnel is disconnected.
3. The AP is running properly, but does not go online.
Error
A fault that affects services occurs and cannot be rectified
automatically. For example, the system fails to load the DRAM or
system software. The fault needs to be rectified manually.
Technical Specifications
50mm×180mm×180mm
400g
Item Description
Dimensions (H x W x D)
Weight
12 V DC (Power adapter)
Output: DC 12V ±10%
Input: 100V ~240V AC
Operating temperature -10℃to +50℃
Relative humidity 10% to 95%
Altitude
Pressure
70kPa to 106kPa
PoE power -48V
–60 m to 4000 m
7

Logging In to the Router
1. Logging In to the AP Through the Console Port
This section describes how to log in to the AP through the console port. After logging in to the AP, you can configure the
AP using commands.
Procedure
Step 1 Connect a PC to the AP with a console cable. Connect the RJ45 connector to the console port of the AP and
connect the DB9 connector to the serial port of the PC. Figure 1-1 shows the location of the AP's console port.
Figure 1-1 Location of the AP's console port
8
Step 2 Run the terminal emulation program on the PC. For example, to open the HyperTerminal of Windows XP on
the PC, choose Start > Programs > Accessories > Communications > HyperTerminal. Enter the name of
the new connection in the Name text box and click OK, as shown in Figure 1-2.
Figure 1-2 Setting up a connection
No Port
1Console port
1
After an AP is powered on, you can log in to the AP using the following methods.
1. Logging In to the AP Through the Console Port
This section describes how to log in to the AP through the console port. After logging in to the AP, you can configure
the AP using commands.
2. Logging In to the AP Using Telnet
This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using
commands.

Logging In to the Router
Step 4 Click Restore Defaults, select 9600 bit/s from the Bits per second drop-down list box, and click OK, as shown
in Figure 1-4.
Figure 1-4 Setting communication parameters
Step 5 Press Enter on the subsequent dialog boxes until the command line prompt of the user view, such as
<Enterprise AP>, is displayed.
You can run commands to configure the AP. Enter a question mark (?) whenever you need help.
----End
9
Step 3 Select the serial port used on the PC and click OK, as shown in Figure 1-3.
Figure 1-3 Selecting the connected port