Huawei UA5000 User manual

UA5000 Universal Access Unit Product
V100R019
Commissioning Guide-PVM CLI
Issue 04
Date 2012-06-25
HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i

About This Document
Intended Audience
This document describes how to commission and verify the basic functions of the UA5000 from
the aspects of hardware, software, interconnection, and maintenance and management. This
ensures that the device runs stably and reliably on the network.
This document also provides the flow and method of commissioning the UA5000.
This document is intended for:
The installation and commissioning engineers
Symbol Conventions
The following symbols may be found in this document. They are defined as follows
Symbol Description
Indicates a hazard with a high level of risk which, if not
avoided, will result in death or serious injury.
Indicates a hazard with a medium or low level of risk which,
if not avoided, could result in minor or moderate injury.
Indicates a potentially hazardous situation that, if not
avoided, could cause equipment damage, data loss, and
performance degradation, or unexpected results.
Indicates a tip that may help you solve a problem or save
your time.
Provides additional information to emphasize or
supplement important points of the main text.
Command Conventions
Convention Description
Boldface The keywords of a command line are in boldface.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI About This Document
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii

Convention Description
Italic Command arguments are in italics.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... } Alternative items are grouped in braces and separated by
vertical bars. One is selected.
[ x | y | ... ] Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } * Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can
be selected.
GUI Conventions
Convention Description
Boldface Buttons, menus, parameters, tabs, window, and dialog titles
are in boldface. For example, click OK.
> Multi-level menus are in boldface and separated by the ">"
signs. For example, choose File > Create > Folder.
Update History
Updates between document issues are cumulative. Therefore, the latest document issue contains
all updates made in previous issues.
Updates in Issue 04 (2012-06-25)
Based on issue 03 (2012-02-25), the document is updated as follows:
Modified:
l3.5.1 Login in the Local Serial Port Mode
l3.5.2 Login in Telnet Mode (Inband Management)
l3.5.3 Login in Telnet Mode (Outband Management)
l3.5.4 Login in SSH Mode (Inband Management)
l3.5.5 Login in SSH Mode (Outband Management)
Updates in Issue 03 (2012-02-25)
Based on issue 02 (2010-06-25), the document is updated as follows:
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI About This Document
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii

Modified:
l3.5.3 Login in Telnet Mode (Outband Management)
l4.4 Commissioning the Interconnection Between the Device and the Router
lA.4.1 Setting the Default System Parameters
lA.4.2 Setting the Default Overseas Parameters
Updates in Issue 02 (2010-06-25)
The structure and content of the document are optimized comprehensively so that the document
can better cater to user preferences and guide users.
Updates in Issue 01 (2009-12-31)
This is the first release.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI About This Document
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv

Contents
About This Document.....................................................................................................................ii
1 Commissioning Description.......................................................................................................1
1.1 Definition............................................................................................................................................................2
1.2 Commissioning Flow..........................................................................................................................................2
2 Commissioning Preparations......................................................................................................4
2.1 Hardware Check.................................................................................................................................................5
2.2 Software Requirements.......................................................................................................................................5
2.3 Tool Requirements.............................................................................................................................................6
2.4 Data Requirements.............................................................................................................................................7
3 Stand-Alone Commissioning......................................................................................................9
3.1 Checking the Settings of Jumpers and DIP Switches.......................................................................................11
3.1.1 Checking the Settings of DIP Switches and Jumpers of Environment Monitoring Boards....................11
3.1.2 Checking the DIP Settings on the Monitoring Board of the Fan.............................................................17
3.2 Powering On the Indoor Device.......................................................................................................................21
3.3 Powering On the Outdoor Device....................................................................................................................22
3.4 Commissioning the Power System...................................................................................................................23
3.4.1 Checking the Power Supply of DC PDU.................................................................................................23
3.4.2 Checking the Power Supply of AC Power Module.................................................................................23
3.4.3 Configuring the Battery and Checking the Power Supply of the Battery................................................24
3.4.4 Checking the Power Supply of the Power Board ...................................................................................25
3.4.5 Checking the Power Supply of the Heat Exchanger................................................................................26
3.5 Logging in to the System..................................................................................................................................27
3.5.1 Login in the Local Serial Port Mode.......................................................................................................27
3.5.2 Login in Telnet Mode (Inband Management).........................................................................................32
3.5.3 Login in Telnet Mode (Outband Management).......................................................................................35
3.5.4 Login in SSH Mode (Inband Management)............................................................................................38
3.5.5 Login in SSH Mode (Outband Management)..........................................................................................48
3.6 Checking the Software Version........................................................................................................................58
3.7 Adding a Shelf..................................................................................................................................................59
3.8 Configuring the Board......................................................................................................................................60
3.9 Loading the Script............................................................................................................................................60
3.10 Configuring the Networking Mode of the System.........................................................................................61
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI Contents
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
v

3.11 Detecting the Power on the Optical Port........................................................................................................61
3.11.1 Detecting the Average Transmit Power of the Two-Fiber Bidirectional Optical Port..........................61
3.11.2 Detecting the Actual Input Power of the Two-Fiber Bidirectional Optical Port...................................65
3.11.3 Detecting the Average Transmit Optical Power of a Single-Fiber Bidirectional Optical Port.............69
3.11.4 Detecting the Actual Input Power of a Single-Fiber Bidirectional Optical Port...................................73
3.12 Checking the Status of the Uplink Port..........................................................................................................78
3.13 Changing the System Name...........................................................................................................................79
3.14 Configuring a System User.............................................................................................................................79
3.14.1 Adding a System User...........................................................................................................................79
3.14.2 Modifying the System User Attributes..................................................................................................81
3.15 Checking the System Time.............................................................................................................................84
3.16 Commissioning the EMU...............................................................................................................................85
3.16.1 Commissioning the ESC EMU..............................................................................................................85
3.16.2 Commissioning the Fan EMU...............................................................................................................86
3.17 Checking the Auto-Save Settings...................................................................................................................88
3.18 Saving the Data...............................................................................................................................................89
3.19 Backing Up the System File...........................................................................................................................90
4 Commissioning the Interconnection.......................................................................................93
4.1 NMS Interconnection Commissioning.............................................................................................................94
4.1.1 Commissioning the Outband NMS..........................................................................................................94
4.1.2 Commissioning the Inband NMS............................................................................................................96
4.2 Commissioning the MG Interface....................................................................................................................99
4.2.1 Commissioning the MG Interface (Through H.248)...............................................................................99
4.2.2 Commissioning the MG Interface Connection (Through MGCP)........................................................101
4.3 Commissioning the Interconnection with the SIP Interface...........................................................................103
4.4 Commissioning the Interconnection Between the Device and the Router.....................................................106
5 Maintenance and Management Commissioning................................................................108
5.1 Checking the Alarm Function and the Event Function..................................................................................109
5.1.1 Verifying the Alarm Function and the Event Function.........................................................................109
5.1.2 Querying Alarms and Events.................................................................................................................111
5.2 Checking the Log............................................................................................................................................112
A Additional Information...........................................................................................................114
A.1 Configuring the IP Address of the Maintenance Terminal............................................................................115
A.2 Making a Script..............................................................................................................................................116
A.3 Operation Guide on Battery Supplementary Charge.....................................................................................117
A.3.1 Preparing Tools.....................................................................................................................................118
A.3.2 Precautions............................................................................................................................................118
A.3.3 Operation Process.................................................................................................................................119
A.4 Software Package Settings.............................................................................................................................120
A.4.1 Setting the Default System Parameters.................................................................................................120
A.4.2 Setting the Default Overseas Parameters..............................................................................................121
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI Contents
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vi

A.4.3 Setting the Default Parameters of the EMU.........................................................................................125
A.5 Acronyms and Abbreviations........................................................................................................................126
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI Contents
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vii

1 Commissioning Description
About This Chapter
This topic describes the definition, prerequisites, and flow of the commissioning.
1.1 Definition
Commissioning refers to the process of verifying the running of the device, the communication
of the device with the NMS and other interconnected devices, and ensuring that the device can
be used as required.
1.2 Commissioning Flow
This topic provides the prerequisites and basic flow for commissioning the device.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 1 Commissioning Description
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1

1.1 Definition
Commissioning refers to the process of verifying the running of the device, the communication
of the device with the NMS and other interconnected devices, and ensuring that the device can
be used as required.
1.2 Commissioning Flow
This topic provides the prerequisites and basic flow for commissioning the device.
NOTE
This flow is for the commissioning procedures in newly-created offices. For the existing offices, adjust the
commissioning procedures and contents according to the actual situation.
Prerequisites
The hardware installation personnel must have installed and checked the UA5000 hardware.
Flowchart
This document describes how to commission the UA5000 in the following steps.
Figure 1-1 provides the commissioning flowchart.
Figure 1-1 Commissioning flowchart
End
Start
Commissioing
preparations
Stand-alone
commissioning
Interconnection
Commissioning
Maintenance and management
commissioning
The following topics provide a brief description about the contents of each chapter:
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 1 Commissioning Description
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2

1. Commissioning Preparations
This topic describes how to prepare hardware, software, tools, and data properly to ensure
that the commissioning is implemented normally.
2. Stand-Alone Commissioning
This topic describes how to commission the stand-alone UA5000 after the hardware
installation so that the stand-alone UA5000 can work in the normal state.
3. Interconnection Commissioning
The administrator can maintain and manage the UA5000 in inband network management
or outband network management mode. This topic describes how to commission the
interconnection by considering the "iManager U2000 unified network management
system" (iManager U2000) as an example.
4. Maintenance and Management Commissioning
This topic describes how to verify the reliability of the device after commissioning the basic
functions and services of the device to ensure the performance reliability of the UA5000.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 1 Commissioning Description
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3

2 Commissioning Preparations
About This Chapter
This topic describes how to prepare hardware, software, tools, and data properly to ensure that
the commissioning is implemented normally.
2.1 Hardware Check
This topic describes how to check the hardware before the commissioning. Make sure that the
hardware is available and check the hardware before the commissioning to facilitate the
subsequent operations.
2.2 Software Requirements
This topic describes the software requirements for the commissioning. You need to prepare the
commissioning software before the commissioning to facilitate the subsequent operations.
2.3 Tool Requirements
This topic describes the tools required for the commissioning. You need to prepare and check
the required tools before the commissioning to facilitate the subsequent operations.
2.4 Data Requirements
This topic describes the data requirements for the commissioning. The information about
hardware configuration, networking, and data plan must be available for data configuration.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 2 Commissioning Preparations
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4

2.1 Hardware Check
This topic describes how to check the hardware before the commissioning. Make sure that the
hardware is available and check the hardware before the commissioning to facilitate the
subsequent operations.
Checklist
Table 2-1 provides the checklist for checking the hardware before the commissioning.
Table 2-1 Hardware checklist
No. Item Description
1Power and
grounding
lEnsure that the power cable and the ground cable are properly
connected.
lEnsure that the power cable, ground cable, and power
distribution switch are labeled correctly, clearly and orderly.
lEnsure that the connectors of external ground cables and
protection ground cables of the cabinet are properly
connected, and they are not damaged.
lEnsure that the power supply of the device is in the normal
state.
2Cables and
connectors
lEnsure that the cable connectors are tight and firm.
lEnsure that the cable jacket is intact.
lEnsure that the cable labels are clear and neat.
lEnsure that cables are bundled reliably.
3 Upper layer
device
lCheck the physical position of the interconnection port on the
upper layer device.
lEnsure that the upper layer device works in the normal state
and can be used for commissioning.
NOTE
The hardware installation personnel must check the device according to items "Power and grounding" and
"Cables and connectors" in Table 2-1 when performing the installation check. The commissioning
personnel can check these two items again to ensure that the hardware connection is reliable during the
commissioning.
2.2 Software Requirements
This topic describes the software requirements for the commissioning. You need to prepare the
commissioning software before the commissioning to facilitate the subsequent operations.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 2 Commissioning Preparations
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5

Checklist
Table 2-2 provides the checklist for checking the required software before the commissioning.
Table 2-2 Software checklist
No. Item Description
1Software
package
Check whether the software package for the commissioning is
complete and the version is correct.
2 Software
commissioning
tools
Check whether the required software commissioning tools are
available. The commonly used commissioning tools are as
follows:
lHyperTerminal: Used for logging in to the UA5000
through the CLI. The tool is embedded in Windows.
lTFTP and FTP: Used for loading software, which can be
downloaded from http://support.huawei.com.
lToolbox: Used for tracing signals. It is released with the
version.
2.3 Tool Requirements
This topic describes the tools required for the commissioning. You need to prepare and check
the required tools before the commissioning to facilitate the subsequent operations.
Checklist
Table 2-3 provides the checklist for checking the required tools before the commissioning.
Table 2-3 Tool checklist
No. Item Description Remarks
1Cables RS-232 serial port cable:
lOne end is an RJ45 connector,
used for connecting to the
control board of the device.
lThe other end is a DB-9 or
DB-25 female connector, used
for connecting to the
commissioning terminal. When
the maintenance terminal is a
PC, use the DB-9 female
connector.
Used for connecting the
commissioning terminal to the
UA5000 in the case of maintenance
through the serial port.
Crossover cable Used for connecting the
commissioning terminal to the
UA5000 in the case of maintenance
in the Telnet mode.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 2 Commissioning Preparations
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6

No. Item Description Remarks
Straight through cable Used for commissioning the
services.
Tail fiber Used for detecting the optical
power and optical sensitivity, and
transmitting the service upstream.
2 Maintain
ing
terminal
(Generally) Portable computer with
HyperTerminal application
Used for logging in to the
UA5000 to commission the
UA5000.
3 Auxiliar
y device
and
meter
Optical power meter Used for the following tests on the
optical port: actual receive optical
power test, receive sensitivity test,
and overload optical power test.
Adjustable optical attenuator Used on the optical signal receive
port for attenuating the received
optical signal during the device
commissioning to protect the
optical port from being damaged by
strong optical power.
Multimeter Used for measuring the voltage,
resistance, and current intensity
during the power commissioning.
2.4 Data Requirements
This topic describes the data requirements for the commissioning. The information about
hardware configuration, networking, and data plan must be available for data configuration.
Checklist
Before the commissioning, collect the information about the hardware configuration,
networking, and data plan based on the engineering documents such as the project division layout
and network design. Table 2-4 provides the data requirement checklist.
Table 2-4 Checklist
No. Item Description
1Hardware
configuration
It includes but is not limited to:
lThe type of the control board and other boards, and the
slot layout.
lThe type of the uplink port and service port, and their
physical locations.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 2 Commissioning Preparations
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7

No. Item Description
2Networking and data
plan
It includes but is not limited to:
lNetwork topology
lIP address allocation
lVLAN plan
lService type and data plan
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 2 Commissioning Preparations
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8

3 Stand-Alone Commissioning
About This Chapter
This topic describes how to commission the stand-alone UA5000 after the hardware installation
so that the stand-alone UA5000 can work in the normal state.
1. 3.1 Checking the Settings of Jumpers and DIP Switches
This topic describes how to check the settings of the environment supervision circuit (ESC)
board, fan EMU jumpers and dual-in-line package (DIP) switches so that the settings
conform to the actual application.
2. 3.2 Powering On the Indoor Device
This topic describes how to power on the indoor device to ensure that each board is supplied
with power in the normal state.
3. 3.3 Powering On the Outdoor Device
This topic describes how to power on the outdoor device to ensure that each board is
supplied with power in the normal state.
4. 3.4 Commissioning the Power System
This topic describes how to commission the reliability of the power supply system so that
the system can supply the power to the device in the normal state.
5. 3.5 Logging in to the System
This topic describes how to log in to theUA5000 and then commission the UA5000 through
the maintenance terminal.
6. 3.6 Checking the Software Version
This topic describes how to check whether the version of the running software meets the
requirements for office deployment.
7. 3.7 Adding a Shelf
This topic describes how to add a shelf (including the master shelf and the slave shelf) to
ensure the normal running of the shelf.
8. 3.8 Configuring the Board
This topic describes how to check whether the inserted board is the same as the board
required in the data plan and check whether the board runs in the normal state.
9. 3.9 Loading the Script
This topic describes how to load the script file to configure the basic data of the device,
which is a preparation for the commissioning of the basic functions of the device.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 3 Stand-Alone Commissioning
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9

10. 3.10 Configuring the Networking Mode of the System
When the networking modes of the UA5000 are different, perform the operation to
configure the networking mode of the system to independent networking or integrated
access networking.
11. 3.11 Detecting the Power on the Optical Port
This topic describes how to detect the mean launched optical power and the actual input
optical power to check whether the transmit optical transceiver and the receive optical
transceiver are in the normal state.
12. 3.12 Checking the Status of the Uplink Port
This topic describes how to check the status of the uplink port to ensure that the
interconnection between the UA5000 and the upper layer device is in the normal state, thus
ensuring the normal communication.
13. 3.13 Changing the System Name
This topic describes how to customize the useful system name to differentiate UA5000s.
This facilitates the management of the UA5000.
14. 3.14 Configuring a System User
When accessing, configuring, and managing the UA5000, you need to add the system
operation users with different attributes. This topic describes how to add system operation
users and modify the attributes of the system operation users.
15. 3.15 Checking the System Time
This topic describes how to check whether the system time, time zone, time stamp, and
start and end Daylight Saving Time (DST) of the UA5000 are consistent with the actual
conditions.
16. 3.16 Commissioning the EMU
The UA5000 provides the function of monitoring various environment parameters (such
as the temperature, humidity, and power voltage) so that the device runs in the stable
environment. This topic describes how to commission the environment monitoring unit
(EMU).
17. 3.17 Checking the Auto-Save Settings
This topic describes how to check the settings of the auto-save function to prevent data loss
due to reboots.
18. 3.18 Saving the Data
This topic describes how to save the data into the flash memory to prevent data loss due to
reboots.
19. 3.19 Backing Up the System File
This topic describes how to back up the system file to prevent permanent data loss due to
the system failure. At the first office deployment or when the upgrade is complete, you
need to back up the database file and the configuration file to restore the system in the case
of the system failure.
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 3 Stand-Alone Commissioning
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10

3.1 Checking the Settings of Jumpers and DIP Switches
This topic describes how to check the settings of the environment supervision circuit (ESC)
board, fan EMU jumpers and dual-in-line package (DIP) switches so that the settings conform
to the actual application.
3.1.1 Checking the Settings of DIP Switches and Jumpers of
Environment Monitoring Boards
This topic describes how to check the settings of the jumpers on the ESC board and the dual-in-
line package (DIP) switches. This ensures that the settings conform to the actual application.
Prerequisites
The UA5000 must be disconnected from the power supply.
Jumpers and DIP Switches of H303ESC
The H303ESC board is located on the right side of the environment monitoring unit (EMU).
The H303ESC board provides six jumpers, namely the S1, S2, S3, S8, S10, and S11, and two
DIP switches S6 and S7. The S5 is the shielding switch of the board alarm buzzer, which is
enabled by default, as shown in Figure 3-1.
Figure 3-1 Layout of jumpers on the H303ESC board and DIP switches
H303ESC
S11
D1
S5
ON OFF
S6
S1 S2
S10
S3 S8
1 2 3
12345678
ON OFF
S7
1234
Jumpers S1, S2, S3, S8 and S10 are used to set the type of the serial port. Table 3-1 provides
their meanings and settings.
Table 3-1 Meanings and settings of the H303ESC S1, S2, S3, S8, and S10
Jumper Settings Meanings Default Settings
S1 1-2 connected The serial port SIO1 is
RS-232.
2-3 connected
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 3 Stand-Alone Commissioning
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11

Jumper Settings Meanings Default Settings
2-3 connected The serial port SIO1 is
RS-422.
S2 1-2 connected The serial port SIO2 is
RS-232.
2-3 connected
2-3 connected The serial port SIO2 is
RS-422.
S3, S8,
and S10
1-2 of S3, S8, and S10
connected
The serial port SIO3 is
RS-232.
1-2 of all jumpers
connected
2-3 of S2 connected; 1-2 of
S8 and S10 connected
The serial port SIO3 is
RS-422.
2-3 of S8 and S10 connected,
S3 connected unlimited
The serial port SIO3 is
RS-485.
S11 is used to check whether the running LED on the front panel is valid. Table 3-2 provides
the meanings and settings of S11.
Table 3-2 Meanings and settings of the H303ESC S11
Jumper Settings Meanings Default
Settings
S11 1-2 connected The running LED on the board
is valid.
1-2 connected
2-3 connected The running LED on the board
is invalid.
DIP switch S6 is used to set the type of external analog sensors. Table 3-3 provides the meanings
and settings of S6.
Table 3-3 Meanings and settings of the H303ESC S6
DIP Switch Settings Meanings Default
Settings
S6-1 to S6-6 ON The external analog sensor is of the
current type.
ON
OFF The external analog sensor is of the
voltage type.
S6-7 to S6-8 Reserved - -
UA5000 Universal Access Unit Product
Commissioning Guide-PVM CLI 3 Stand-Alone Commissioning
Issue 04 (2012-06-25) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12