Huazheng HZBB-10S User manual

HZBB-10S
Portable Transformer Turns Ratio
Tester
Huazheng Electric Manufacturing (Baoding) Co., Ltd

Dear user:
Thank you for choosing HZBB-10S Portable Transformer Turns Ratio
Tester.
We hope that this instrument can make your work easier and more
enjoyable, so that you can get the feeling of office automation in the test
and analysis work.
Before using the instrument, please read this manual, and operate and
maintain the instrument according to the manual to prolong its service life.
"Just a light press, the test will be completed automatically" is the
operating characteristics of this instrument.
If you are satisfied with this instrument, please tell your colleagues;
if you are not satisfied with this instrument, please call [phone] to
tell you to serve you at all times-Baoding Huazheng Electric Manufacturing
Co., Ltd., our company will definitely make you satisfied !

Contents
I.Important Note............................................................................................................................... 1
II.Introduction................................................................................................................................... 1
III.Packaging Content..................................................................................................................... 1
IV.Functional Characteristics......................................................................................................... 2
V.Technical Indicators..................................................................................................................... 2
VI.Adjust The Wristband.................................................................................................................3
VII.Battery Charging........................................................................................................................3
VIII.Tilt Hand-held Tester................................................................................................................4
IX.Product Appearance.................................................................................................................. 4
X.Operation Instructions.................................................................................................................6
XI.Matters Needing Attention.......................................................................................................11
XII.Packing List..............................................................................................................................12

1
I.Important Note
If the instrument is not in use, please turn off the power in time.
If the instrument is not used for a long time, please charge and discharge regularly.
Batteries should be charged and discharged at least once a month.
It is strictly forbidden to use power shortage, which will severely shorten the battery
life and even make the battery scrap. When the instrument is short of power, the power
supply should be switched off and charged immediately. Avoid battery failure due to
excessive battery discharge time.
Charging lamp: the charging lamp on the charger is bright red during charging and
bright green after charging.
Users must not disassemble the instrument and replace the battery without
authorization. When the instrument or battery fails, please return to the factory.
II.Introduction
Hand-held transformer turn ratio tester is an innovative product with compact size,
hand-held operation, more portable and easy to carry.
Products are mainly applied to change than group test transformer, PT and CT
polarity test, test speed, high accuracy.
III.Packaging Content
After receiving the packing box, open the packing box and check if there is any
damage. If the freight packing box is damaged or the liner material is indented, please
inform the freight company or our salesman immediately.
Please check if you have received the following items in the product package：
Standard accessories：
√1 Hand-held transformer turn ratio tester
√1 sets of test lines (red and black each)
√1 charger
√1 external printer (with printing cable attached）
√1 wrist band (attached to a hand-held tester)）

2
√1 print user manual
√1 copy of certificate and factory test report
IV.Functional Characteristics
Lithium battery power supply or 100-240V AC power supply is self-adaptive.
After one charge, more than 100 transformers can be continuously tested in
the ratio group. The test process is simple and convenient.
It has the function of blind measurement, that is, to perform variable ratio
and group test when there is no connection between high and low voltage.
Based on the test of conventional transformer, Z-type transformer and PT
sample, the polarity test function of CT variable ratio is added, and the
application field is wider
Wide range and high accuracy, the variable ratio measurement range can
reach 10,000, and the test accuracy can be guaranteed 0.3% when the
maximum value is 10,000.
It has perfect protection functions such as reverse connection protection
and output short circuit protection.
5.6-inch super industrial high-brightness color LCD screen, still visible
under strong sunlight.
equipped with external printer, facilitate data printing
It can be stored locally and on USB memory.
V.Technical Indicators
Range
0.9～10000
Accuracy
±（Reading×0.1%+2 words）（≤500）
±（Reading×0.2%+2 words）（>500≤3000）
±（Reading×0.3%+2 words）（>3000）
Resolution ration
0.9～9.9999（0.0001）
10～99.999（0.001）

3
100～999.99（0.01）
1000～9999.9（0.1）
10000 and above（1）
Working power
supply
The built-in battery or external charger,
charger conditions of use，Input 100-240 VAC，
50/60 HZ
Charging time
About 2 hr
Instrument weight
1.7 kg
Instrument
dimension
246 mm（L）×156 mm（W）×62 mm（H）
Use of
temperature
-10℃～50℃
Relative humidity
≤90%，No dew
VI.Adjust The Wristband
For better grip, strip the belt and adjust the adhesive tape as shown in the following
figure.
VII.Battery Charging
When the battery is low after long storage or before the first use of the handheld
device, please use the charger attached to it to charge the battery for at least 2 hours,
and continue to use the hand-held tester when charging. When the battery is fully
charged, the charger light changes from red to green.

4
VIII.Tilt Hand-held Tester
In order to take the instrument or expose the side interface during operation, the
hand-held tester can be tilted, as shown in the figure below.
Lift the tilt seat and pull outward
IX.Product Appearance
Top view

5
Front View
Side View
Function
module
Instructions
High
voltage
test
terminal
The yellow, green and red three-color junction seats correspond to
three-phase A, B and C respectively, and the red test line corresponds to the
bullet rod side. The other end of the test line has yellow, green and red
three-color test clamps, which correspond to three-phase A, B and C of the
high voltage side of the transformer under test; the yellow and green test
lines are connected to single-phase test.
Low
voltage
test
terminal
The yellow, green and red three-color junction bases correspond to the
three-phase of a, B and C respectively, and the black test line corresponds
to the bullet rod side. The other end of the test line has yellow, green and
red three-color test clamps, which correspond to the three-phase of a, B and
C on the low-voltage side of the transformer under test; the yellow and
green test lines are connected to the single-phase test.
Display
5.6 inch large industrial high brightness color LCD screen, display operation
menu and test results.

6
Button
Operate instruments. “↑↓” is the "up and down" key, select to move or modify
data; “←→” is the "left and right" key, select to move or modify data; "Enter"
key, confirm the current operation; "Cancel" key, abandon the current
operation.
Function
module
Instructions
Power
switch
The power switch of the whole machine is switched to the open position
when it is switched on. Switch to the close position when it is switched off.
RS 232
interface
Connect external printer.
Charging
interface
Use instrument charger to recharge.
USB
interface
External USB disk is used to store test data, please use FAT or FAT32
format U disk; in the storage process, it is strictly prohibited to dial out the
USB disk.
X.Operation Instructions
Single phase transformer or single phase PT test wiring
The yellow and green test clamps of the red test line at the high-voltage test end
are connected to the high-voltage end of the tested product, and the yellow and
green test clamps of the black test line at the low-voltage test end are connected to
the low-voltage end of the tested product.
Single phase CT test wiring
The yellow and green test clamps of the red test line at the high voltage test end
are connected to the second side of the tested product, and the yellow and
green test clamps of the black test line at the low voltage test end are connected to
the first side of the tested product.
Test wiring for three phase transformer
The yellow, green and red test clamps of the red test line at the high-voltage test
end connect the A, B and C phases at the high-voltage end of the tested product;
the yellow, green and red test clamps of the black test line at the low-voltage test end
connect the a, B and C phases at the low-voltage end of the tested product.
Intelligent power management
When the instrument is not operated for a long time, the LCD backlight is
automatically dimmed to save power; the instrument has the function of charging

7
prompt with low power and over-discharge protection; when the instrument is low
power, the charger can be plugged in to charge, and the instrument can be used
normally in the charging process.
Instructions for use of printer
The key of the printer and the indicator of the printer are integrated. When the
printer is powered on, the indicator light is normally on, and it flashes when the paper
is missing. Press the button once and the printer passes the paper.
Printer change paper: take out the rotating spanner and open the paper cover;
Load the printer paper and pull out a piece of printer paper (tear the teeth out a little
bit). Close the cover and press the print head to the print head. Press the print head
back to the print head with a bit of force.
Operation instruction
After all the test wires are connected, turn on the power switch and enter the
"main menu" screen after the instrument is initialized, as shown in the figure below.
NO.
Instructions
1
Display date and time.
2
Displays the peripheral and current operation status.
This icon is displayed when you insert a USB drive.
This icon is displayed when the printer is inserted.
This icon is displayed when storing information queries.
NO.
Instructions
3
The power of the instrument shows that the icon flickers when the power is
low.
4
In the main menu operation area of the instrument, the corresponding