HULALA HOME SBBSD0588 User manual

ITEM NO.
SBBSD0588
NOTE:
This brochure contains IMPORTANT safty info. Please read
and keep for future reference.
HULALA
H O M E

MAINTAINANCE
AND WARNING
Keep furniture away from heat sources.
Do not clean furniture with harsh cleaner
or polishes. Do not use detergents,
Solvents, abrasives, spray packs or
leather cleaner. Usenon-color mild soap
with warm water to clean spills(Mix 1:10
soap to water)
Do not place furniture under direct
sunlight, material will possibly fade over
time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture that is not
protectedby a padded barrier .
Not for commercial use, only for
residential use 。
Weight Limitation
80LBS

OVERVIEW
A
C
D
G
G
G
GF
F
H
H
II
B
K
JL
M
N
N
P
I
I
O
E

Persons Required For Assembly
：
HARDWARE
LIST
A
2Personen
1 PC
BC
D
1 PC 1 PC 1 PC
E
1 PC
FG
4 PCS
H
I J
L
K
4 PCS
2 PCS
1 PC
M
2 PCS
NO
1 PC
1 PC
1 PC 1 PC
2 PCS
P
1 PC

PARTS
LIST 1
Be sure to inspect all packing material
carefully for small parts, that may have
come loose inside the carton during
shipment.
SPARE
x10 x4
x1 x76 x8 x4
x7x16x10
#1 #4 #5 #6 #7
#8 #9 #12 #17
x1 x1
x1 x1 x1 x1
x1x1x1
#1 #4 #5 #6 #7
#8 #9 #12 #17
∅6*35mm M7*50mm M6*12mm M6*35mm M6*45mm
M6*45mm M3.5*14mm M4*22mm M4*35mm
∅6*35mm M7*50mm M6*12mm M6*35mm M6*45mm
M6*45mm M3.5*14mm M4*22mm M4*35mm

PARTS
LIST 2
Be sure to inspect all packing material
carefully for small parts, that may have
come loose inside the carton during
shipment.
x4 x4 x24
x8 x10 x1 x4 x4
x2 x1 x2
x10x12 #3 #11 #13
#15 #16
#22
#21
#2
#18 #19
#20
#14
#10
∅8*30mm ∅15*11mm
∅8*30mm
M4∅20MM

ASSEMBLY
INSTRUCTIONS
STEP1:
Insert wooden dowel #2 into the corresponding hole of top
panel (A),and then screw bolt #1 into the corresponding hole
of top panel (A) ， tighten bolt #1 with screwdriver #21
.
#1 󲻅1󲹽 󲻅󲺃
󲺎
#2 󲻅1 #21
#21
#1󲻅1󲹽
#2󲻅󲺃
#1
#1
#1
#1
#1
#1
#1
#1
#2
#2
#2
∅6*35mm ∅8*30mm

STEP2:
Insert side panel (D)&(C)
、 middle vertical panel(E) into the
preassemble top panel (A),and then insert cam bolt #3 into
the corresponding hole of side panel (C)&(D)&middle vertical
panel(E),tighten cam bolt #3 with screwdriver #21,finally stick
paster #15 to it for look nice.
x6 x1
󲺎
󲺑
󲺐
󲺒
x6
󲹰1󲺂󲹰󲺀 󲹰󲹿1
󲹰󲺀x6
󲹰󲹿1
󲹰1󲺂x6
󲹰󲺀
󲹰󲺀
󲹰󲺀
󲹰󲺀
󲹰󲺀
󲹰󲺀
󲹰1󲺂
󲹰1󲺂
󲺐&D&E󲺐&D&E󲺐&D&E
󲺎
󲺎
󲺎
∅15*11mm ∅20MM

STEP3:
Insert panel(F) into preassemble top panel(A) as picture show
， and then insert cam bolt #3 into the corresponding hole of
panel (F),tighten cam bolt #3 with screwdriver #21
，finally
stick paster #15 to it for look nice.
A
F
F
x4 x1x4
#15#3 #21
#15x4
#21
#3x4
#3
#3 #15
#15
F
A
F
A
F
A
D
C
E
∅15*11mm ∅20MM

STEP4:
Carefully align and slide panel (G) into the groove along rear
edge of pre-assemble step 3,and then insert wooden dowel
#2 into the corresponding hole of panel(C)&(D)&(E)
.
F
F
G
G
G
G
C
󲺑
󲻅󲺃
#2
#2󲻅󲺃
#2
#2
#2
E
A
∅8*30mm