Human Touch HT-9200 Setup guide

X1103
October 17, 2010
REMOVING THE FOOT-AND-CALF MASSAGER
1. Using two people, gently tip the chair onto its side (Fig.1).
2. Use the remote control to deploy the foot-and-calf massager until the connector box becomes
accessible (about 75% full deployment) (Fig.2).
3. Power off the chair, then unplug it.
4. Using a nail clipper or other suitable instrument, cut the zip ties that secure the connector box
to the chair frame (Fig.2).
5. Using a Phillips-head screwdriver, remove the four screws that secure the connector box cover,
then remove the cover (Fig.3).
6. Disconnect the connectors (Fig.4)
7. Using a nail clippers or any other suitable instrument, cut the zip-tie that secures the massager harness
to the frame (Fig.5).
Tools Required: Phillips-head screwdriver, nail clippers or other instrument suitable for cutting zip ties, new zip ties. NOTE: SAVE ALL SCREWS FOR USE DURING REASSEMBLY.
REPLACING THE FOOT-AND-CALF MASSAGER
HT-820/9200
It is imperative that Human Touch® products are repaired in a manner that ensures product safety and regulatory compliance and that is fully consistent with the practices used
during the manufacturing process. Therefore, Human Touch requires that all product repairs are performed using only factory-new parts and in accordance with these repair
instructions. Failure to adhere to these instructions voids the product warranty and releases Human Touch from all liability for injury or product damage resulting from the repair.
SERVICE LEVEL: 3
1
(Fig.1)
Zip ties (Fig.2)
Connector box
(Fig.3)
Connectors
(Fig.4)
Zip-tie
(Fig.5)

2
8. Locate the two screws located inside the foot-and-calf massager’s rubber housing and remove them (Fig.6).
9. Using a Phillips-head screwdriver, remove the two screws that secure the fabric strip that holds the rubber housing in place, then remove the fabric strip (Fig.7).
10. Locate the five Phillips-head screws that secure the opposite side of the fabric strip that holds the rubber housing in place, then remove the screws and strip (Fig.8).
11. Using a Phillips-head screwdriver, remove the two screws that secure the two fabric strips that secure the foot-and-calf massager to the frame (Fig.9).
12. Pull the foot-and-calf massager forward to remove it from the chair (Fig.10).
(Fig.6)
Fabric strip
(Fig.7)
(Fig.8) (Fig.9) (Fig.10)
Foot-and-calf massager
Foot-and-calf
massager

INSTALLING THE FOOT-AND-CALF MASSAGER
1. Place the foot and calf massager into position on the frame.
2. Place the fabric strip that secures the foot-and-calf massager to the frame into position, then secure it using two Phillips-head screws (Fig.11).
3. Place the fabric strip that secures the top rubber housing into position then secure it using Five Phillips-head screws (Fig.12).
4. Place the fabric strip that secure the bottom rubber housing into position then secure it using two Phillips-head screws (Fig.13).
5. Replace the two screws inside the open slot in the rubber housing.
6. On the underside of the chair, reconnect the connectors.
7. Using the zip-tie, secure the calf massager harness to the frame (Fig.14).
8. Place the connectors into position inside the connector junction box (Fig.15), replace the junction box cover, then replace the four screws
to secure it (Fig.16).
9. Use a new zip tie to secure the connector box to the chair frame (Fig.17).
10. Using two people, gently return the chair to an upright position.
11. Plug in the chair, power it on, then verify that the new foot and calf massager is working properly.
(Fig.11)
Foot-and-calf
massager
(Fig.12)
Fabric strip
(Fig.13)
(Fig.15) (Fig.16)
Zip ties
(Fig.17)
Connector box
Connectors
Please send any questions or comments regarding these instructions to: [email protected]
© 2010 Human Touch®, LLC. 3
Zip-tie
(Fig.14)