Husqvarna Automower Connect 2G User manual

EN, English
Operator's manual
Automower® Connect
Read the operator's manual carefully and make sure that you
understand the instructions before you use the product.

Contents
1 Introduction.......................................................2
2 Getting started..................................................2
3 Settings.............................................................3
4 Operation..........................................................3
5 Technical data.................................................. 4
1 Introduction
1.1 Description
Automower® Connect brings the menu system
to your mobile device, making it easy to read
and change the product settings remotely.
Through this application, you can receive the
current status of the product and send
commands to the product from anywhere in
the world. In case of theft, you get an alarm
and can monitor the position of the product.
1.2 Installation
The Automower® Connect accessory must be
installed by a dealer. The installation includes
a software update of the product.
2 Getting started
You can communicate with your product
through the mobile application Automower®
Connect. With Automower® Connect
activated, new symbols will show on the
display of the product.
Note: All countries do not support
Automower® Connect because of legal
reasons and regional specified cellular
systems. The included Automower® Connect
lifetime service only applies if there is a third
part sub-supplier of 2G/3G/4G available in the
operational area. In some countries
Bluetooth® is not available due to legal
reasons.
2.1 Download the Automower®
Connect app
Download the Automower® Connect app from
App Store or Google Play to your mobile
device.
2.2 Create an Automower® Connect
account
When you have downloaded the app, you can
enter your e-mail address and a password to
make an Automower® Connect account. You
will receive a validation e-mail to your e-mail
address. Follow the instructions in the e-mail
in less than 24 hours to validate your account.
If not validated in less than 24 hours, you must
make a account again. You can pair the
product and your mobile device when the
account has been made in the app.
2.3 Pair with Automower® Connect
1. Start the app on your mobile device and
log in to your account.
2. Select
Menu > My mowers .
3. Push + ta add a new product. Follow the
instructions in the app.
4. Select
Menu > Accessories >
Automower® Connect .
5. Enter the PIN code.
6. Select Pairing > New pairing in the menu
of the product.
7. Enter the 6-digit code shown on the
display of the product.
2 - Introduction 1438 - 002 - 17.01.2020

3 Settings
Display and change the settings of the product
from everywhere in the world. For security
reasons you must use short-range
communication (Bluetooth®) if you change
General and Security settings, or disable the
Automower® Connect module on the product.
3.1 To set the GeoFence center
The GeoFence function makes it possible to
monitor the product, for example in case of
theft. Before GeoFence can be used, its
center point and sensitivity must be set. This
can only be done from the menu in the
product.
1. Put the product in the center of the work
area.
2. Select
Accessories > Automower®
Connect
.
3. Enter the PIN code.
4. Select GeoFence .
5. Select Activate GeoFence and push OK.
6. Select
New center point to set the source
for GeoFence.
GeoFence sensitivity can be changed.
Sensitivity can be set to Low, Medium or High .
The higher the sensitivity, the easier the alarm
is activated.
Note: When you put the product into storage
for a long period, it is recommended to switch
off the main switch to save battery power. With
the GeoFence function on, a PIN code is
necessary to switch off the product. If you
switch off the main switch, the Automower®
Connect stays on for 12 hours. After that it is
not possible to communicate with the product
and the GeoFence function is not on.
3.2 Symbols on the display
These symbols are shown on the display of
the product when Automower® Connect is
enabled.
The signal strength of the GPRS
reception.
Problem with the connection to the
Internet server.
Problem with the SIM card or the
module.
4 Operation
4.1 Main menu
• Dashboard : Shows the current status of
the product. It shows symbols for the
battery status and cutting height.
• Map : Shows the current position of the
product and the set centerpoint for
GeoFence. You can monitor the
movement of the product with this
function, for example in case of theft.
•
Messages (only available for Bluetooth®
short-range connectivity): In this menu the
fault and information messages can be
found. For some of the messages, there
is information to help you to correct the
fault.
4.2 My mowers
My mowers shows the status of the product,
you can remove or add products paired to the
account.
1438 - 002 - 17.01.2020 Settings - 3

5 Technical data
5.1 Technical data
Frequency Band Support
Automower® Connect 2G GSM 850 MHz, E-GSM 900 MHz, DCS 1800 MHz, PCS 1900 MHz
Automower® Connect 3G Band 19 (800 MHz), Band 5 (850 MHz), Band 8 (900 MHz), Band 2
(1900 MHz), Band 1 (2100 MHz)
Automower® Connect 4G Band 12 (700 MHz), Band 17 (700 MHz), Band 28 (700 MHz), Band
13 (700 MHz), Band 20 (800 MHz), Band 26 (850 MHz), Band 5
(850 MHz), Band 19 (850 MHz), Band 8 (900 MHz), Band 4 (1700
MHz), Band 3 (1800 MHz), Band 2 (1900 MHz), Band 25 (1900
MHz), Band 1 (2100 MHz), Band 39 (1900 MHz)
Power Class
Automower® Connect 2G Power Class 4 (for GSM/E-GSM) 33 dBm
Power Class 1 (for DCS/PCS) 30 dBm
Automower® Connect 3G Power Class 3 24 dBm
Automower® Connect 4G Power Class 3 23 dBm
4 - Technical data 1438 - 002 - 17.01.2020

1438 - 002 - 17.01.2020 Technical data - 5

6 - Technical data 1438 - 002 - 17.01.2020

1438 - 002 - 17.01.2020 Technical data - 7

AUTOMOWER®is a trademark owned by Husqvarna AB.
Copyright©2020 HUSQVARNA. All rights reserved.
www.husqvarna.com
Original instructions
1141799-28
2020-01-17