HySecurity HYNET SFP 4/1 User manual

Installation Manual for HyNet Attachment Kit: MX3868
This document is a supplemental document that provides specic information regarding
conguration of the HySecurity gate operator with installation and wiring of the HyNet Gateway. For
safety considerations and information specic to your gate operator, refer to the HySecurity gate
operator's product manuals.
StrongArm M30, StrongArm M50,
HydraSupply XL, HydraWedge SM50

HyNet Components
2D0720 Rev. B HyNet Aachment Kit: MX3868 ©2019 www.hysecurity.com
Drawing is not to scale
LED Indicators
Height
1¼ inches
SFP Module
(100/1000/2500)
Managed Switch
RJ-45 Integration Hub
4-Port Copper Gigabit
(100/1000/2500)
Micro USB
Reset Button
RS-485
USB OTG
Micro SD Card Slot
Mounting Plate
4 x 7½ inches
LED (position 1)
Table 1: HyNet LED Indicators
LED Position LED Color Indicates
1RED ashing No communication from gate operator to HyNet.
1Green steady Communication is established between gate operator and HyNet.
2RED steady Gate operator network communication is not congured or established.
2RED ashing HyNet is attempting to connect to network (web interface).
2GREEN ashing Network (web interface) is established and working. (May not be wholly
congured, yet. Verify conguration with your IT administrator.)
3RED steady Hardware fault.
3RED ashing Charge is low on coin battery. Replace coin battery.
3GREEN steady Hardware functioning and coin battery charged.
4Red steady or no LED lit HyNet internal switch is not functioning.
4GREEN steady HyNet internal switch is functioning.
4321

HySecurity CRASH Products and
HyNet Assembly with Attachment Bracket
DIN rail mount
Bracket mounting screws
HyNet Mounting Plate
Attachment Bracket
DIN rail mounting screws
Star washers
Tools Required
• Phillips head screwdriver
www.hysecurity.com ©2019 StrongArmCRASH, HydraWedge SM50, HydraSupply XL Installation D0720 Rev. B 3

HyNet Assembly
DIN Rail Mount
Attachment
bracket
HyNet
Mounting plate
Mount HyNet module
onto DIN rail next to
Power Disconnect
Switch.
HyNet Installation on
StrongArm M30 Control
Panel
4D0720 Rev. B HyNet Aachment Kit: MX3868 ©2019 www.hysecurity.com

Mount HyNet Assembly to DIN Rail
Mount the HyNet assembly to the DIN rail inside the gate operator or HydraSupply.
NOTE: The HydraSupply cabinet (not shown) contains a DIN rail and the HyNet is mounted similarly to it.
12
1
12
2
Tip the HyNet Assembly so the
spring loaded pins t under the
DIN rail.
Pull on the DIN rail mount
to slide and set the opposite
section over the DIN rail.
NOTE: The DIN rail mount is
interchangeable and can be
assembled so that the spring
loaded pins clasp onto the
top rail or the bottom rail.
NOTE: For clarication only, DIN rail
and DIN rail mount shown without
HyNet Assembly attached.
StrongArm M30
HyNet Assembly shown attached to DIN rail in Pivot Post
12
3
DIN rail
Pins
Springs
DIN rail mount
DIN
rail
HyNet Assembly
www.hysecurity.com ©2019 StrongArmCRASH, HydraWedge SM50, HydraSupply XL Installation D0720 Rev. B 5

HyNet Gateway
Pin 1, COM
Installer supplied
shielded cable
STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
SENSOR 1
SENSOR COM
DO NOT USE
DO NOT USE
DO NOT USE
CHARGER
AC LOSS
LOCK INTERLOCK
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT DUAL GATE RADIO OPTIONS
DRIVE POWER RS485
MOTOR USER 1 USER 2
USER 3
VEHICLE DETECTORVEHICLE DETECTORVEHICLE DETECTOR
STOP/BUZZER
FREE EXIT
INSIDE OBSTR
OUTSIDE OBSTR
SHADOW RESET
WIEGAND
HySecurity
COM
NO
MX000585
VERSION
S/N
RS232
DISPLAY
VEHICLE DETECTOR
COM COMA B
RPM
COMOPEN S 1+24V +24V
STAT U S
LED
Inputs
SENSOR 2
SENSOR 3
(+24V) (-24V)
BLACK
TERMINAL
BLOCKS
RED
TERMINAL
BLOCKS
Pin 1, +24V
DO NOT connect to +24V tabs at base of
Smart Touch Controller. Only use the +24V
connections on the power supply terminal
block.
CAUTION
Drawing is not to scale.
Attach shielded cable
to wire harness.*
2
1Attach to RS-485
port on HyNet.
3Connect to RS-485 port on
Smart Touch Controller.
4
Snip off lug and strip
wire. Connect ying
lead to +24VDC
terminal block.
Tact
button
Wire harness
(supplied in box)
5
Supply RJ-45 network
connection
HyNet
RS-485
port
Smart Touch Controller
RS-485
Connector
RS-485 Connector
RS-485 ports
*Measure distance between
HyNet and Controller
connections for appropriate
shielded cable length.
6D0720 Rev. B HyNet Aachment Kit: MX3868 ©2019 www.hysecurity.com
NOTE: More detailed wiring information
is shipped with the HyNet.

STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
SENSOR 1
SENSOR COM
DO NOT USE
DO NOT USE
DO NOT USE
CHARGER
AC LOSS
LOCK INTERLOCK
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT DUAL GATE RADIO OPTIONS
DRIVE POWER RS485
MOTOR USER 1 USER 2
USER 3
VEHICLE DETECTORVEHICLE DETECTORVEHICLE DETECTOR
STOP/BUZZER
FREE EXIT
INSIDE OBSTR
OUTSIDE OBSTR
SHADOW RESET
WIEGAND
HySecurity
COM
NO
MX000585
VERSION
S/N
RS232
DISPLAY
VEHICLE DETECTOR
COM COMA B
RPM
COMOPEN S 1+24V +24V
STAT U S
LED
Inputs
SENSOR 2
SENSOR 3
(+24V) (-24V)
BLACK
TERMINAL
BLOCKS
RED
TERMINAL
BLOCKS
Smart Touch Controller
RS-485
Connector
Menu
button
Select
button
Reset
button
Open
button
SA 1
SYSTEM ADDRESS
Press Select again to set gate operator's system
address (Each gate operator attached to the
same HyNet must have a unique SA number.
Choose 1, 2, 3, or 4.)
2
1To access Installer Menu, press Menu button
twice. Then, press Reset and Open.
Press Select to navigate to Installer Menu item
"SA" System Address.
3To exit Menu mode, press Menu. The gate
operator returns to Run mode.
4Refer to "Table 1: HyNet LED Indicators"
on page 2. Solid green means serial
communication is active and functioning well.
HySecurity gate operators provide a 2-wire, serial interface (RS-485 connection) which allows remote access to
one or more operators.
When the physical connection is made and protocols are established, an SA (System Address) must be assigned
for each operator through its Installer Menu.
For network communication, choosing a “SA” of 1 to 4 establishes individual network polling addresses. HyNet
only utilizes numbers 1, 2, 3, or 4.
A “SA” of zero means no network communication is desired.
5For IP network setup, refer to the HyNet Quick
Start manual supplied in the HyNet box..
Tact
button
Common Bus (-)
www.hysecurity.com ©2019 StrongArmCRASH, HydraWedge SM50, HydraSupply XL Installation D0720 Rev. B 7

Installer’sCheCklIst
Date Installed: ________________ Gate Operator Model: _________________________________________________________________
Site Location:__________________________________________________________________________________________________________
HyNet Serial Number:___________________________________
Gate Operator Serial Number: ___________________________
Gate Operator Serial Number: ___________________________
Gate Operator Serial Number: ___________________________
Gate Operator Serial Number: ___________________________
Customer Name:_______________________________________________________________________________________________________
Mailing Address:________________________________________ Inspected by: ____________________________________________
________________________________________________________ Date Inspected: __________________________________________
Phone Contact: _________________________________________ Phone contact number: ___________________________________
Checked Initials
1. Site Planning _____________
RJ-45 cable to system network.
2. Safety _____________
Review Important Safety Information in the gate operator's product manual.
Warning labels apparent and afxed properly.
Area around the gate and gate operator free of debris, cabinets/chassis include locking mechanism.
3. Electrical _____________
3.1 Grounding
• NFPA 780 Standard for the Installation of Lighting Protection Systems.
• Solid copper ground rod (C\,-inch diameter, 10 ft length) driven into ground within 3 ft of the gate operator.
• Single length of unspliced 6AWG copper wire less than 3 ft long attached to lug nut in gate operator.
3.2 Gate operator has current software loaded.
3.3 Congure the Controller
• Set the System Address (SA) in the Installer Menu.
• Communicate (verify) system address to IT Network Admin for proper web page conguration.
4. Review gate operator installation checklist from gate operator manual _____________
5. Take photographs of installation and provide an End User Demo _____________
8D0720 Rev. B HyNet Aachment Kit: MX3868 ©2019 www.hysecurity.com