IBM 3454-CAC User manual

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 1
IBM Cloud Pak for Data System
Customer Install Guide
100G Spine Switch
3454-CAC
Version 1.3
Note
Before using this information and the product it supports, read the information in
“Safety notices” on page 5, “Notices” on page 33, the IBM Systems Safety Notices
manual, G229-9054, and the IBM Environmental Notices and User Guide.

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 2
This edition applies to IBM Cloud Pak for Data System Components.
Revised November 2021
© Copyright IBM Corporation 2020, 2021.
US Government Users Restricted Rights –Use, duplication or disclosure restricted by
GSA ADP Schedule Contract with IBM Corp.

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 3
Contents
Safety..............................................................................................................................4
Safety Notices.................................................................................................................5
Publications...................................................................................................................13
Cloud Pak for Data System 100G spine switch description...........................................14
Cloud Pak for Data System 100G spine switch hardware specifications.......................15
Operating Environment .................................................................................................16
Rack requirements........................................................................................................17
Rack space................................................................................................................17
Location in the rack.......................................................................................................18
Package contents:.........................................................................................................20
Contents: 00RR851, duct kit......................................................................................20
Contents: 3454-CAC spine switch .............................................................................21
Installation procedure....................................................................................................21
Installing 100G spine switches in a rack....................................................................21
Before you begin.....................................................................................................21
About this task........................................................................................................21
Electronic Emissions Notices........................................................................................27
Regulatory and Compliance..........................................................................................32
Notices..........................................................................................................................33
Copyright License:.........................................................................................................36
Trademarks...................................................................................................................37
Readers’ Comments......................................................................................................38

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 4
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 5
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten
Safety Notices
These statements provide the caution and danger information used in this documentation.
Important:
Each caution and danger statement in this documentation is labeled with a number. This number
is used to cross reference an English-language caution or danger statement with translated
versions of the caution or danger statement in the Safety Notices Translation document (PN
G229-9054).
For example, if a caution statement is labeled "D005," translations for that caution statement are
in the Safety Notices Translation document under "D005."
Be sure to read all caution and danger statements in this documentation before you perform the
procedures. Read any additional safety information that comes with your system or optional
device before you install the device.
D005
DANGER: When working on or around the system, observe the following precautions:

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 6
Electrical voltage and current from power, telephone, and communication cables are
hazardous. To avoid a shock hazard:
•If IBM supplied the power cord(s), connect power to this unit only with the IBM
provided power cord. Do not use the IBM provided power cord for any other
product.
•Do not open or service any power supply assembly.
•Do not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
•The product might be equipped with multiple power cords. To remove all
hazardous voltages, disconnect all power cords.
oFor AC power, disconnect all power cords from their AC power source.
oFor racks with a DC power distribution panel (PDP), disconnect the
customer’s DC power source to the PDP.
•When connecting power to the product ensure all power cables are properly
connected.
oFor racks with AC power, connect all power cords to a properly wired and
grounded electrical outlet. Ensure that the outlet supplies proper voltage
and phase rotation according to the system rating plate.
oFor racks with a DC power distribution panel (PDP), connect the
customer’s DC power source to the PDP. Ensure that the proper polarity is
used when attaching the DC power and DC power return wiring.
•Connect any equipment that will be attached to this product to properly wired
outlets.
•When possible, use one hand only to connect or disconnect signal cables.
•Never turn on any equipment when there is evidence of fire, water, or structural
damage.
•Do not attempt to switch on power to the machine until all possible unsafe
conditions are corrected.
•Assume that an electrical safety hazard is present. Perform all continuity,
grounding, and power checks specified during the subsystem installation
procedures to ensure that the machine meets safety requirements.
•Do not continue with the inspection if any unsafe conditions are present.
•Before you open the device covers, unless instructed otherwise in the installation
and configuration procedures: Disconnect the attached AC power cords, turn off
the applicable circuit breakers located in the rack power distribution panel (PDP),
and disconnect any telecommunications systems, networks, and modems.
DANGER:

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 7
•Connect and disconnect cables as described in the following procedures when
installing, moving, or opening covers on this product or attached devices.
To Disconnect:
1. Turn off everything (unless instructed otherwise).
2. For AC power, remove the power cords from the outlets.
3. For racks with a DC power distribution panel (PDP), turn off the circuit
breakers located in the PDP and remove the power from the Customer's
DC power source.
4. Remove the signal cables from the connectors.
5. Remove all cables from the devices.
To connect:
6. Turn off everything (unless instructed otherwise).
7. Attach all cables to the devices.
8. Attach the signal cables to the connectors.
9. For AC power, attach the power cords to the outlets.
10.For racks with a DC power distribution panel (PDP), restore the power
from the Customer's DC power source and turn on the circuit breakers
located in the PDP.
11.Turn on the devices.
Sharp edges, corners and joints may be present in and around the system. Use care when
handling equipment to avoid cuts, scrapes and pinching. (D005)
C002
CAUTION: Only trained service personnel may replace this battery. The battery contains
lithium. To avoid possible explosion, do not burn or charge the battery.
Do not:
•Throw or immerse into water
•Heat to more than 100°C (212°F)
•Repair or disassemble
Exchange only with the approved part. Recycle or discard the battery as instructed by local
regulations. (C002)

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 8
C026
CAUTION: This product might contain one or more of the following devices: CD-ROM
drive, DVDROM drive, DVD-RAM drive, or laser module, which are Class 1 laser
products. Note the following information:
•Do not remove the covers. Removing the covers of the laser product could result
in exposure to hazardous laser radiation. There are no serviceable parts inside
the device.
•Use of the controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
(C026)
IBM® servers can use I/O cards or features that are fiber-optic based and that utilize
lasers or LEDs.
Laser compliance
IBM servers may be installed inside or outside of an IT equipment rack.
All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR
Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in
compliance with IEC 60825 as a class 1 laser product. Consult the label on each part
for laser certification numbers and approval information.
CAUTION:
Data processing environments can contain equipment transmitting on system links with
laser modules that operate at greater than Class 1 power levels. For this reason, never
look into the end of an optical fiber cable or open receptacle. Although shining light into
one end and looking into the other end of a disconnected optical fiber to verify the
continuity of optic fibers many not injure the eye, this procedure is potentially
dangerous. Therefore, verifying the continuity of optical fibers by shining light into one
end and looking at the other end is not recommended. To verify continuity of a fiber
optic cable, use an optical light source and power meter. (C027)
CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments.
(C028)
CAUTION:

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 9
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the
following information: laser radiation when open. Do not stare into the beam, do not
view directly with optical instruments, and avoid direct exposure to the beam. (C030)
CAUTION: To reduce the risk of electric shock or energy hazards:
This equipment must be installed by trained service personnel in a restricted-access
location, as defined by the NEC, IEC 60950 and IEC 62368, The Standard for Safety of
Information Technology Equipment.
(R001 part 1)
DANGER: Observe the following precautions when working on or around your IT rack
system:
•Heavy equipment–personal injury or equipment damage might result if
mishandled.
•Always lower the leveling pads on the rack cabinet.
•Always install stabilizer brackets on the rack cabinet unless the earthquake
option is to be installed.
•To avoid hazardous conditions due to uneven mechanical loading, always install
the heaviest devices in the bottom of the rack cabinet. Always install servers and
optional devices starting from the bottom of the rack cabinet.
•Rack-mounted devices are not to be used as shelves or work spaces. Do not
place objects on top of rack-mounted devices. In addition, do not lean on rack
mounted devices and do not use them to stabilize your body position (for
example, when working from a ladder).

© Copyright IBM Corporation 2020, 2021 Customer Install Guide, 100G Switch 10
•Each rack cabinet might have more than one power cord.
oFor AC powered racks, be sure to disconnect all power cords in the rack
cabinet when directed to disconnect power during servicing.
oFor racks with a DC power distribution panel (PDP), turn off the circuit
breaker that controls the power to the system unit(s), or disconnect the
customer’s DC power source, when directed to disconnect power during
servicing.
•Connect all devices installed in a rack cabinet to power devices installed in the
same rack cabinet. Do not plug a power cord from a device installed in one rack
cabinet into a power device installed in a different rack cabinet.
•An electrical outlet that is not correctly wired could place hazardous voltage on
the metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock. (R001 part 1)
R007
CAUTION: Use safe practices when lifting.
L001