Icegame DODGEBALL User manual

Diagnostics and trouble shooting guide
Your game comes with extensive diagnostics to aid you in keeping your game running correctly.
To access the diagnostics, open the left lower door assembly.
Press the “SELECT” and “DOWN” buttons at the same time in attract mode.
NOTE - GAME MUST BE IN ATTRACT MODE TO ENTER DIAGNOSTICS
In diagnostics, the Jumbotron will show the layout of the sensor boards.
It will light the location of the board in green when selected. You will notice the remainder of
the sensors are yellow. This indicates the remaining boards are sending and receiving
information. If you see any red, this would indicate the board in that location is not receiving
or sending information.
GREEN = Selected Sensor board.
YELLOW = Communication is established.
RED = No communication, check power or RJ45 for proper connections.
You will also notice the numbers under “ID DIPS”. This indicates the proper dip switch setting
for this location. IT IS NOT READING THE DIPSWITCHES! It is only showing you the proper
settings for that location. White means it should be set to on while blue means it should be set
to off.
At the bottom of the screen, it will show you which RGB color the target should be. It will cycle
from Red to green to blue and repeat.
S1 and S2 have different meanings depending on which sensor you are testing.
More details on this later on.

When in diagnostics if you press the “Press to enter initials” button it will cycle through
the sensor board numbers and light the location of the sensor.
Each press of any podium button will flash that button. You can use either podium.
When you press the “LEFT” button on any swing target, the swing arm will move inward.
If you press the “RIGHT” button the swing arm will move outward. S1S2 shows means
switch 1 and switch 2. On a swing arm target, only S1 is used. When the arm swings
inwards S1 will appear. When the swing arm is returned to the outward position, S1 will
disappear. When visible, the status of that switch is high. When invisible, the status of
that switch is low.
“PRESS TO ENTER INITIALS” = Change sensor board number.
“LEFT” = Swing target arm inward (only on sensor 1 through 14).
“RIGHT” = Swing target outward (only on sensor 1 through 14).
“S1S2” = Status for switch 1 and switch 2. Visible = high, invisible = low.
Press the “1P” button and the game will dispense 5 tickets.
If you trigger the coin line a sound will play.
The selected sensor board will show the digits on the display counting up.
For target board 15, S1 indicates the left hole and S2 indicates the right hole.
For target board 16, the upper red display will cycle numbers and the “LEFT” and “RIGHT” buttons will swing the arm back and fourth.
For target board 17, the upper blue display will cycle numbers and when you press “LEFT” and “RIGHT” buttons, the ball gate will
operate.
Boards with IDs 18 through 22 only use S2 and will disappear when you press the back wall buttons.

DB2033X Target PCB ID numbers
Boards 1 - 14 are Swinging Targets. Board 15 is Bonus holes and displays.
Board 16 is Block Arm and Player 2 score display. Board 17 is Player 1 display and strobe lights.
Boards 18 - 22 are bonus button assemblies.
LEFT TOWER RIGHT TOWER
LEFT MIDDLE TOWER RIGHT MIDDLE TOWER
CENTER BUTTON
WALL
LEFT BUTTON WALL RIGHT BUTTON WALL
JUMBOTRON BOARDS

DB2033X Target PCB Dipswitch settings
Each board has two sets of dipswitches. These dipswitches determine the position and function. When installing any replacement
boards, confirm the location of the board and set the dipswitches to match the location.
Both RJ45 ports are identical. Either can be used for in or out communications.

TO FRONT OF GAME
Right TowerRight Buon
Center Buon
Right Center TowerLe Center Tower
Le Buon
Le Tower
NETWORK WIRING COLOR CODE