Icegame WORLD FOOTBALL PRO PS1000X User manual

1
Service Manual
[phone]
WWW.ICEGAME.COM
Innovative Concepts in Entertainment
10123 Main street
Clarence, New York 14120

2
Table of Contents
Safety and Warnings 3
UCL Connector 4
SETUP
UNPACKING YOUR PALLET 5
GAME ASSEMBLY 8
FINAL GAME SETUP 30
FIRST TIME POWER ON 31
PROGRAMMING 32
VOLUME CONTROLS (OPTIONS AND AMP) 33
DIAGNOSTIC MENU 34
WARRANTY 35
Rev C 6/5/2023

3
SAFETY AND WARNINGS BEFORE YOU BEGIN
WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED.
FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A
GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO
THE ELECTRONICS.
NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.
DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME
REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR
WARRANTY.
HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND
IS FUNCTIONING PROPERLY.
THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING
PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE
STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE.
THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES
OTHER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT
FOR VOLTAGE CONVERSION INFORMATION.
WARNING
DO NOT remove any of the components on the main board (e.g. compact flash and eproms)
while the game is powered on. This may cause permanent damage to the parts and the main
board. Removing any main board component part while powered on will void the warranty.
ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE,
UNLESS NEEDED FOR SPECIFIC TESTING. FAILURE TO OBSERVE THIS PRECAUTION
COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.
THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE
USED.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
AC Power Information
The games main fuse is accessed through the back of the game at the power mod. Above the
power cord is a small panel that contains the main fuse.
The value of the fuse for 120 volt 60Hz is 5 AMPS at 250Volt type slow blow.
The value of the fuse for 220/230 volt 50/60Hz is 3 AMPS at 250 Volt type slow blow.

4
Debit Card Housing use:
Molex 9-pin housing 03-09-2092
Universal Card link Connection
See Wiring Insert for wire colors and which connections are used.
Pin 1. +12v- Supply to Card System = Minimum of 2A available for the card systems and a Max of 3A.
Pin 2. Coin 1 - input to the game PCB.
Pin 3. Prize Meter/Ticket Notch 2- is connected to the Ticket Notch line between the game PCB and ticket dispenser.
Optional.
Pin 4. Coin Meter 1 - is connected to the coin meter 1 output from the game PCB and can be used by card systems for
monitoring purposes.
Pin 5. Ticket Run/Enable 2- is connected to the ticket run line between the game PCB and ticket dispenser. Optional.
Pin 6. Prize Meter/Ticket Notch 1- is connected to the Prize or Ticket Meter output from the game PCB and can be
used by card systems for monitoring purposes. Optional.
Pin 7. Coin Inhibit/Enable- is connected to the Coin or Note Inhibit/Enable output from the Game PCB and is used
where the game has this feature for disabling any payment. This is normally for states like New Jersey that limit the
amount of money that can be inserted at one time.
Pin 8. Ticket Run/Enable 1 - is connected to the ticket run line between the game PCB and ticket dispenser in standard
redemption games. This is commonly used for systems using paperless or E-ticket. Not Used if the game doesn’t have
this output.
Pin 9. Ground- is connected to the common Ground connection, the same ground as the Game PCB.

5
(PS1014X)
(PS1028) (PS1028) (PS1029)
(PS1030)
Slide cages out.
(PS3095)
UNPACKING YOUR PALLET
Cut strap to remove
front floor assembly
(PS1014X).

6
Remove floor assembly
from pallet.
Cut strap to remove other assemblies.
(PS7027X) (PS1031)
(PS3115)
(PS3116)
(PS3050X)
LEFT CHANNEL COVER RIGHT CHANNEL COVER
(PS1031)
(PS7029)
(PS7030)
(PS3079)

7
(PS3022X)
Remove both podiums.
(PS1005X) (PS1006X)
Remove the remaining items
found in the
(PS1022-P800)
(PS3024) X’s 8
(CG2027)
(AA1050)
(PS3070X)
(PS1023-P800)
(PS6000X)
PS3122
PS1001
AA6718 (3)
AA6212 (3)
(PS7010)
PS4009X
PS3039 PS3037X
Purchased
Option

8
Attach one PS3079 trim piece using three AA6213 bolts and AA6212
washers to the left and right side of the back assembly (PS3070X).

9
(PS3050X
)
With a helper, lay the PS3050X assembly down on the ground.
(PS3050X)
(PS3070X)
(PS3050X)
Lift the PS3070X assembly onto the PS3050X assembly.

10
Secure the back assembly onto the floor assembly using three
AA6886 screws on each side shown below.
AA6886
X’ 6
At both sides of the cabinet, unlock the access panel and remove.
On the right side, plug in two harnesses.

11
On the Left side, plug in two harnesses.
Unlock and remove the top back access panel.

12
Remove the lower panel of the PS3050X assembly.
Plug in the Network cable into the open RJ45 slot.

13
From the front of the game, insert one PS4006 foam pad, then PS7010
Goalie, another PS4006 pad and then the PS1001X sweeper assembly.
Pem studs are located at the back of this mount.
Note, floor assembly components removed for clarity.
PS4006
PS1001X
PS7010
PC60604
X’s 4
From the back of the game, use four PC606004 nylon nuts to secure the
assembly.
* CUT ZIP TIES TO RELEASE RUBBER PADS ON GOALIE.

14
(PS1023-P800)
(PS1022-P800)
(PS7027X)
Attach the left (PS1022-P800) bracket and the right (PS1023-P800)
bracket to the PS7027X marquee assembly using eight PC60622
Allen bolts, four per bracket.
PC60622
X’s 8
Attach the marquee assembly on top at the back of the game using
PC60622 Allen bolts, four per support, eight total.
4 X’s
4 X’s
PC60622
X’s 8

15
Slide the left cage (PS1028-p705) onto the top lip of the cabinet as shown.
Plug in the harness for the marquee.

16
INSIDE OF CABINET
PC60622
X’s 4
Secure the cage to the cabinet using four PC60622 Allen bolts.
WARNING - CAGE WILL NOT BE COMPLETELY STABLE UNTIL TOP CAGE ASSEMBLY IS ATTACHED.
Slide the right cage (PS1028-705) onto the top lip of the cabinet as shown.

17
WARNING - CAGE WILL NOT BE COMPLETELY STABLE UNTIL TOP CAGE ASSEMBLY IS ATTACHED.
Secure the cage to the cabinet using four PC60622 Allen bolts.
PC60622
X’s 6
Right side shown, repeat for left side.
Position two PS1031 trim panels at each side of the top cage (PS1029-
P705) and attach them using twelve PC60622 Allen bolts, six on each side.
PC60622
X’s 4

18
Place two cheat support brackets under neath the top cage and put the
cheat assembly on top of the cage with the brackets to the inside of the
cheat assembly. Attach using below hardware.
AA6155
X’s 4
AA6031
X’s 8
AA6004A
X’s 4
Placement of optional cheat sensor should be at the back of the cage.
It should be close to center and not to one side.
NOTE: This cheat sensor is not included with the game and can be
purchased separately.

19
PC60622
X’s 12
WARNING -
CAGE WILL NOT BE COMPLETELY
STABLE UNTIL TOP CAGE ASSEMBLY
IS ATTACHED.
A helper is highly recommended to stabilize the side cages while placing the
top cage assembly onto the side cages! Secure the cage top assembly
using six PC60622 Allen bolts to each side top as shown.
From the front of the game, insert the LED power connectors through the
hole at each side. Then from the back, connect them to the game.

20
Plug in the cheat sensor harness if purchased.
**Note - Never plug in harness with the power on! Damage will occur to the sensor.