icetro ISI-271THS User manual

SOFT ICE CREAM
SELF MACHINE
User's Manual
ISI-271THS
ISI-271SHS
●
This product is designed for indoor use .
●
Make sure to install it indoors.
●
The appearance, design, color, and parts of the product
are subject to change without prior notice.

2
Soft ice cream Self machine offers the following advantages
1. Minimum noise and refreshing cooling system
2. MICOM control method
3. Pasteurization function implemented
4. Defrost function implemented
5. Color LED lamp light
7. Convenient washing system
8. Inverter system application
6. Body response button used
With a high efficiency and low noise motor, we can achieve minimal noise from the
refreshing cooling system
Use of an artificial intelligence control type achieves an optimal cooling system.
A low-temperature pasteurization process is implemented for heating products at 68°C for 30
minutes to supply sanitary ice cream products sans the spoilage of materials.
The soft ice cream inside the cylinder can be defrosted to liquids
Color LED lamp lights are mounted to enhance the effects of lighting and
demonstration and for maximized marketing effects.
Feedwater lines are directly connected to the system; the model with pasteurization
functions allows using boiling water when cleaning the cylinder and the storage tank to
facilitate the cleaning of the system.
By allowing separate speed controls for producing and projecting soft ice-cream,
you can have the best ice cream quality.
Push button design for easy operation.

3
Thank you very much for purchasing a soft ice cream self machine made by ICETRO. For correct
use of the product and its maintenance, please read this manual carefully. If a problem occurs while
using the product, you can refer to this manual for troubleshooting. This manual contains a product
warranty, so keep it safely for future reference. This product can be installed only by someone
qualied for installation. If use of parts and accessories not provided or approved by ICETRO or any
part or accessories made by ICETRO but remodeled by other person causes a problem, we are not
responsible for if nancially. (The functions and specications shown in this manual and on the web
site are subject to change without notice. Please visit our website at http://www.icetro.com to obtain
the latest specications
Contents
Cautions for your safety ........................................................................................................ 4~8
Unpacking and Installation method ....................................................................................... 9~10
Name of each part ................................................................................................................ 11~14
Product specication
............................................................................................................. 15
Check prior to use.................................................................................................................. 16
Button display names and functions ..................................................................................... 17
Functional description of the buttons .................................................................................... 18~22
Explanation of the function button ........................................................................................ 23~42
“3 category” ........................................................................................................................ 23~25
“4 category” ........................................................................................................................ 26~38
“9 category” ........................................................................................................................ 39~44
How to check the operation of each part .............................................................................. 44
Sale related Settings ........................................................................................................... 45~48
Making soft ice cream ........................................................................................................ 49
How to pasteurize the soft ice cream ................................................................................. 50
How to make the soft ice cream look better ........................................................................ 51
Caburator control ................................................................................................................ 52
Cleaning method .................................................................................................................. 53~55
Dasher and dasher cover assembly method .................................................................... 56
How to upgrade the program ............................................................................................... 57
How to use USB downloader ............................................................................................... 58~64
How to adjust the LED indicators ......................................................................................... 65
Service for Refrigerant Lines ................................................................................................ 66~68
Removal and Replacement of Compressor ........................................................................... 69
Removal and Replacement of Capillary Tube ........................................................................ 70
Removal and Replacement of Hot Gas Valve or Liquid Line Valve. ..................................... 71
Removal and Replacement of Condenser’ ............................................................................ 72
Replacement of Fan motor / Replacement of 4-way valve.................................................... 73
Circuit diagram
.................................................................................................................. 74
Refrigeration circuit diagram
........................................................................................... 75
Before requesting service
................................................................................................. 76~77
Replacement cycle of consumable parts
........................................................................ 77
Error Codes and Corrective Actions ..................................................................................... 78~79
Product warranty ............................................................................................................... 80
Dear customers

4
The caution/warning details for safety are intended to prevent accident or danger through
safe and proper use. Therefore please follow the details accordingly. The precaution details
are categorized into warning and caution, and the respective meanings are as follows.
Note: Original instructions is provided by ICETRO Co., Ltd.
※Personal Injury: Minor cuts, burns (high or low temperature) or electric shocks that
do not need hospitalization or long-term hospital visiting.
※ Property Loss: The loss on houses, household goods, livestock, bedding, and such.
This means that it can cause death or major injury
when the details are violated.
If you neglect this symbol and wrongly use the product,
it may cause a re, serious injury or death.
Warning
Danger
Caution This means that it can cause injury or house/
property damage when the details are violated.
[Each symbol has the following meanings]
This symbol means that it can be dangerous in specic conditions.
This symbol means never to do the described action.
This symbol means not to touch specic parts with bear hands.
This symbol means to unplug the power from the outlet.
Must be grounded.
This symbol means not to disassemble the product.
This symbol means to be careful because there is a possibility of
electric shock.
Cautions for your safety

5
Cautions for your safety
Call a service center
Observe the regulations Check your labels
Label
Warning
Caution
For relocation of the product, call an expert. Keep your warning and caution
labels clean for easy legibility.
The product may cause such hazards as
falling down unless properly installed.
It should be installed in accordance with related
regulations such as KS standards, the road and
trafc act. The re ghting act and the food sani-
tation act. ※ Call your distributor.
If the user misunderstands
the content of such a label,
an accident may occur.
Call an expert for repair.
Imperfect repair may cause re,
electric shock or injury.
If you think the product
needs repairing, call
your distributor.
When you dispose of the
product, consult a disposal
expert.
An accident may result unless
it is properly disposed of.
※ Call your distributor.
Caution
Caution
If the power cable needs
replacement or repair,
call a service center or
an expert.
Caution
Do not place any obstacle at
the entrance of the air vent.
The side and rear of the product
should be maintained at least
20cm from the wall. If no t so,
the performance will be degraded
When you replenish ice cream
raw materials do not allow
rain or snow to get into any
interior electric part.
Defective operation may occur. Electric shock or injury may r
esult.
Before you clean the inside
of the product, unplug the
earth leakage breaker
wearing rubber gloves.
Caution
Caution
Caution
Otherwise, the ingredients
can deday.
If sterilization is not done
every day, you are recommen
ded towash it every day.
To have good soft
icecream, it is recom-
mended topasteurize or
cleanit everyday.
EVERYDAY
Caution
It can cause damages to
the product.
Do not use or store
inammablegas or material
near the product.

6
Cautions for your safety
User’s
Manual
It can cause electrical
shocks or res.
without the manual,
an accident may occur
because of erroneous
handing or operation.
Do not install it near dust,
moisture or rainwater(water)
popping.
The appliance has to be
placed in a horizontal
position
It can cause physical injury
or product damages.
It can cause damages to
the product.
Do not install it on a tilt.
Do not apply excessive force
orimpact to the product.
This product shows
the Optimal performance
at temperature of 10~30°C.
Do not operate the product
while all panels are not well
fastened enough.
Caution Caution
Caution
Caution
Caution
Caution
While operating the product,
please close the upper cap
completely. Do not arbitrarily connect
the power cord or process
it for use.
Bugs or alien substances
can enterthe product.
It can cause res.
Caution
Prohibited
Prohibited
Do not put anything on the
product.
Injury may occur if it falls over.
Fire or electric shock
may occur.
Oh! NO
Prohibited
If you sell or hand over
the product, make sure
to hand over the user’s
manual with it.
Note: Translations of the original instructions
is provied by ICETRO co., Ltd.
Do not put anything on
the power cable.
Make sure that
the power cable is not
twisted or knotted.

7
Cautions for your safety
Prohibited
Prohibited
Prohibited
Do not spray with
an insecticide,
ammable spray or
perfume near
the product.
Do not climb onto
the product or
shake or tilt it.
Do not inject inammable
material such as benzene,
gasoline, paint thinner or
LP gas into the product
otto keep it close to
product
Make sure that no electric part
has come into contact with water.
If the product was
immersed in water by a ood,
call a service center for
a check. Otherwise,
re or electric shock due to
electric leakage may occur.
Explosion, re or injury
may occur.
Fire or electric shock
may occur.
The product may fall down
or develop a problem.
Prohibited
If the supply cord is damaged,
it must be replaced by the manufacture,
its service agent or similarly qualitied
persons in order to avoid a harzard.
Fire or electric shock
may occur.
Oh! NO
Prohibited
Do not place water containers,
medicine, foods, small metal
parts or inammable material
on top of the product.
If they go inside the product,
it cancause electrical shocks,
re anddamages.
Prohibited
Keep a heating device away
from the power cable.
A heating device may melt
down the coating of the
power core, resulting
in re or electric shock.
Prohibited
Prohibited
Prohibited
Do not place candle lights
or cigarettes light on top of
theproduct.
Do not put anything on the
product.
It can cause res.
Injury may occur
if it falls over.
Do not touch any moving part inside the
product.
You may get injured.
Prohibited
Thinner
Gas Ga
sol
ine

8
Strongly warn children about
its danger.
It may cause an electric
shock or product damage.
The damage will go to
the machine or there is
a possibility which Will be injured.
Do not insert your nger
or other materials into the
panel rubber or the
machine supply.
Prohibited
Prohibited
Electric shock or
injury may result.
It can cause electrical
shocks or res.
Never put your hands
into the rod of the cup
conveyor.
Do not use or store
inammable gas or material
near the product.
Prohibited
Prohibited
Take care not to press
the push button during
the pasteurization or
defrost process.
Prohibited
Do not disassemble or
alter the product.
Electric shock, re or
injury may occur.
Prohibited
Do not touch the power cable
or any elctric part with wet
hands.
Explosion, re or injury may
occur.
You may burn injuries.
Prohibited
Prohibited
Stop operating the product if
you hear any unusual noise
or smell or if you see smoke
coming out from the product.
If you continue to operate the
machine in such a condition,
re or electric shock may result.
Cautions for your safety
Don’t let an uneducated
person or a child touch
or operate the machine.
The machine can be
damaged, or an injury
may occur.
Please do not press “WASH” button during
empty condition which the
cylinder doesn’t contain any
ingredients or water.
The bearing of drum can be
frayed because
there is no lubrication.

9
This marking indicated that
this product should not be
disposed with other
household wastes
throughout the EU.
To provent possible harm
to the environment or
human health from
uncontrolled waste disposal,
recycle it responsibly to
promote the sustainable
reuse of material resources.
To return your used device,
please use the return and
collection systems or
contact the retailer
where the product was purchased.
They can take this product for
environmental safe recycling
The installation instructions for
appliances of the supervised
type shall state that
the appliance is only to
be installed in locations
where it can be overseen
by trained personnel.
The instructions for appliances
connected to the water mains
by detachable hose-sets
shall state that
the new hose-sets
supplied with the appliance
are to be used and that
old hosesets
should not be reused.
Note: The approved water supply hose should
be used, which is on condition that IEC
61770 and EN 50084 are satised.
This appliance is not
intended for use by persons
(including children)
with reduced physical,
sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been given
supervision or instruction
concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if the have been given supervision
or instruction concerning use of the
appliance a safe way and understand the
hazards involved.
Children should be supervised to ensure that
they do not play with the appliance.
Prohibited
Prohibited
Cautions for your safety
The instructions shall state that
access to the service area
is restricted to persons
having knowledge and
practical experience
of the appliance,
in particular as far as
safety and hygiene are
concerned.

10
The Soft Ice Cream Self Machine has been fully inspected and tested at the factory prior to shipping.
If you detect damage to the wooden package or apparent distortion of the shape of the system
after unpacking the product, immediately inform your distributor or manufacturer.
Find the serial number marked on the packing and the machine before starting installation.
Inform us of the serial number if you have any inquiry. Request the dealer or service provider
for assistance when the machine is to be moved.
1. Remove the wooden packing, taking care not to damage the exterior of the Soft Ice Cream
Self Machine.
2. Remove the wooden packaging and the protective tapes and make sure that all parts of
the system are complete.
※ When tilting or moving the machine, take care not to overturn the machine.
1. Avoid sloping or irregular surface.
- Installation on a sloping or an irregular surface may result in machine overturning, malfunction,
or failure.
2. Avoid direct sunlight, rain, snow, and wind.
- Otherwise, re or electric shock may occur due to the ice cream or rain water.
3. Avoid the direct inuence of sea wind and hazardous gases.
- Soft Ice cream Self Machine buyers may complain or le a claim.
●
Location and Precautions for Installation
Unpacking and Installation method

11
Waring ●Before install the unit, be sure electrical ground at outlet.
●The installation instructions for appliances of the supervised type shall state that
The appliance is only to be installed in locations where in can be overseen
by trained personnel.
Bury the copper plate or ground rod at a depth of 30 cm or more underground.
Failure to perform ground work may cause electric shock caused by leakage.
※ Check the followings after connecting the feed and discharge water lines:
1. Feed water pressure should be between 1~3 kgf / ㎠.
▶If the water pressure is too high, water may leak at connections.
2. If the temperature can go down below 10℃, provide a means to prevent freezing.
▶Freezing can cause water leakage or failure of the system.
3. There should be a tap water valve when you connect the system to tap water.
Close the tap water valve if there is water leak due to a defect of the tap on
top of the product.
The raw water supply valve may vary depending on the installation environment of the system.
1. Fir rubber packing in the corrugated tube nut
of the feed water line and join it to the water
inlet of the product.
Tighten the nut rmly with a tool.
2. Pay special attention to protecting Section “A”
from damage when assembling the tools.
- Consult with the engineers of the company for the details of installation of the system to ensure optimal
performance of the system (change of the installation site of the system also requires consultation with
the engineer of the company).
- Do not install the system on a place with adverse conditions such as uneven oor, place exposed to direct
light, or place with too much dusts or direct splashing of water.
- Rest the current time when restarting after a long standstill.
● Electrical connection
●How to install!
● Water Supply Connection
1. Connect the plug to designed voltage that single phase (220-240) V, 50Hz.
2. Earth shall be provided for the safe operation of the system.
3.
Maintain space of 50cm or more each between the walls and the right and rear sides,
20cm or more between the left of the system.
4. Precisely seat the rubber feet at the bottom to prevent slipping.
Do not ground the unit
to the gas pipe or
water pipe.
Caution
It can cause an accident.
How to install
50cm
20cm
50cm
BALL
VALVE
A
30 cm or more

12
Name of each part
Front view
COVER BASKET
WATER
VALVE
LCD
WINDOW
CONTROL
BUTTON
SELECT
BUTTON
PUSH
BUTTON
WASH BUTTON
TOP COVER
POWER SWITCH
DASHER COVER
DASHER COVER
BOLT
CUP SENSOR
FEEDER
DRAIN BOX
FOOT
CONDENSER FILTER INSIDE: CONDENSER
FILTER
ISI-271SHS
ISI-271THS
LOCK
RAW STORES
LOCK
920
380
1400
380

13
Name of each part
Left view
Right view
FRONT
COVER UP
INSIDE:
CONTROL BOX
FEEDER
ROAD
Note: For buyer request, it can be movable designed.
(Caster or leg)
SIDE
PANEL L
FEEDER
COVER
DRAIN SLUG
SIDE LUVER L
FEEDER
COVER
SIDE PANEL R
CASTER
ISI-271SHS
ISI-271THS
840 840
646 196
106
920
660
1400
1140

14
Name of each part
Back view
INSIDE: COMP
BACK PANEL
Feedwater
section
Power
supply
INSIDE:
INVERTER
Remote control
switch connector
ISI-271SHS
ISI-271THS
INSIDE: SMPS

15
Name of each part
BRUSH COVER
BRUSH CARBURETOR IN
BRUSH DRUM
BRUSH CARBURETOR OUT
HANDLE JOINT BOLT
CABURATOR PACKING
SHAFT POM PACKING
PACKING DASHER COVER
DASHER LUG FRONT WHITE
DASHER LUG BACK WHITE
HINES
MANUAL
1 EA
1 EA
1 EA
1 EA
1 EA
1 EA
1 EA
CABURATOR TUBE
1 EA CABURATOR TUBE
BODY ASSY
1 EA
1 EA
2 EA
2 EA
1 EA
1 EA
Parts

16
CLASSIFICATION SPECIFICATION
Product name SOFT ICE CREAM SELF MACHINE
Model name ISI - 271THS, ISI - 271SHS
Rated voltage and frequency 1Φ, (220-240) V, 50 Hz
Power consumption 12.3 A 2400 W / 12.6 A 2500 W
Product size
(including
the wheel)
WIDTH 380 mm
HEIGHT 940 mm / 1400 mm
DEPTH 840 mm
Cylinder capacity
(Mixing tank capacity)
2.7ℓ
(12.2ℓ )
Number of dispensed cups
without interval
40 cups
(Under conditions of ambient temperature of 27 °C
and ice cream weight of 80 grams)
Cooling temperature Can keep under 5 ℃
Condenser Fully sealed compressor
Pasteurization function 68 ℃ 30Minute Pasteurized
Ice cream weight 80 g ± 15 g(Variation allowed)
Filter mounted bottom lter / Intermediate lter
Refrigerant amount 730 g / 800 g
Refrigerant kind R404A
Product weight(Before packing) 130 Kg / 150 Kg
Maximum water pressure 0.98 MPa
Minimum water pressure 0.09 MPa
Product specication

17
Check prior to use
【Make sure to check them prior to use 】
If you intend to leave it unused for a long time, wash it and turn off the water supply
valve and turn off the earth leakage circuit breaker.
The air suction and discharge should be facilitated so that the cooling
performance can be optimized.
For better taste of soft ice cream, do not miss the lter cleaning time.
It is recommended to clean the cylinder, the mixing tank,the impeller, the dasher,
the caburator, the cup sensor, the piston every day.
Clean the condenser at least once a month or more often.
The cylinder, impeller, dasher, or piston inside the product makes a contact
with the ingredient, so you should clean them once every day.
● Do not block the air vent.
● Periodic lter cleaning
● Clean the condenser once a month.
● Pasteurize it at least once a day.
For your
information

18
[ A u t o ] I c e c r e a m L e v e l
6 0 % / 6 0 %
M i d d l e
1 . 5
[ A ]
B r e a k T i m e
8 . 0 m i n / 8 . 0 m i n
Button display names and functions
‘STOP’
‘WASH’
‘STAND-BY’
‘PASTEURIZE’
‘DEFROST’
‘ DISPLAY WINDOW ’
‘MIX-LOW’
‘SELECT’
‘CHK’
‘SET’
‘AUTO’
● Button is used to stop all
the functions.
● Used when defrosting
the soft ice cream.
● Used when the Soft
ice cream solution is
watery.
● Button is for wash
function
● Used for boiling water
when cleaning the
system
● while the raw material in the
cylinder and the hopper is
being refrigerated.
● Button is used to check
the temperature.
● Set the functions relevant to sales.
● Self-service sale and remote sale may be
selected by simultaneously pressing
‘CHK’ and ‘SELECT’ buttons.
● Pressing this button once discharges a single
cup; and keeping this button pressed for three
seconds or longer, single-cup sales test is
allowed.
● Button is used to change the setting.
Press the
‘
DEC.
’
&
‘
INC.
’
buttons at the same time for five
seconds to lock or unlock the
touch buttons.
●Used when pasteurizing
the soft ice cream or
the raw material in the
hopper.
● Lamp blinks when there are
insufcient ingredients.
The light blinks if there are
no raw materials.
● Button is used to make
soft ice cream.
●Displays the degree of soft ice
cream formation in operation.
PASTEURIZE
PASTEURIZE
REGENERATION
BOILING
(Heating, Heat)
‘BOILING’
(‘DEFROST’+‘WASH’)
‘REGENERATION’

19
[ A u t o ] I c e c r e a m L e v e l
[ A u t o ]
[ T e m p e r a t u r e ]
6 0 % / 6 0 %
N o w L o a d : 1 . 2 A / 1 . 2 A
S e t L o a d : 1 . 5 A / 1 . 5 A
N o L o a d : 1 . 0 A / 1 . 0 A
H o p p e r : 8 . 2 °C / 8 . 2 °C
D r u m : - 6 . 2 °C / - 6 . 2 °C
B r e a k T i m e
8 . 0 m i n / 8 . 0 m i n
Functional description of the buttons
【 Detail description of each mode
】
Making soft ice cream in ‘AUTO’ mode.
To check ‘AUTO’ mode level set up
After making soft ice cream in
the ‘AUTO’ mode.
To see the raw material information of the
mixing tank in the ‘AUTO’ mode
Pour the raw material in the mixing tank and press the
‘AUTO’ button. The following status display will be shown.
To see the information of the raw material in the hopper,
press ‘SET’ button:
When soft ice cream has produced,
the compressor will be shutdown for a while, and
the status will be displayer as shown to the right.
① Current level of soft ice cream is indicated.
④
Information including the temperature of the hopper
and cylinder can be obtained.
③
At Operation mode, if you push ‘ DEC. ’ button
1 time, piston time decreases by 0.1 second.
If you push ‘ INC. ’ button 1 time, piston time
increases by 0.1 second.
(Max : Values of ‘ 3-8-2 ’ or ‘ 3-10-2 ’ of each mode)
⑤
The time remaining until the restarting of the compressor
will be displayed in Min unit.
(If the ambient temperature is high, the compressor may
start up earlier than the time indicated.)
② Press the ‘SELECT’ button to display the level
setting (Current, Set-up, No-load) of soft ice cream.
to change soft ice cream level setting, press the
‘SET’ button for three seconds.
(For futher details, see ‘Adjusting Setting
Value’ section.)
②
⑤
To change temperature, press the ‘SET’ button for
three seconds.
(For further details, see ‘ Adjusting Setting Value ’
section.)
⑥
Soft ice cream level is indicated.
(After indicating 100%, the value will decrease as time
passes, faster if the ambient temperature is higher.).
The soft ice cream level is set to the default by the manufacturer. Depending on the types of ingredients
and the abrasion of the blade, it should be adjusted properly. When installing this equipment,
the settings for the ingredients should be based on the suggestion by the installation technician.
When changing the ingredients, consult with a professional to adjust the setting.
④
⑥
For your
information
[ A u t o ] I c e c r e a m L e v e l
6 0 % / 6 0 %
B r e a k T i m e
8 . 0 m i n / 8 . 0 m i n
③
①
M i d d l e
1 . 5
[ A ]
M i d d l e
1 . 5
[ A ]

20
Functional description of the buttons
【 Detail description of each mode 】
[ R e g n r . ] C y l i n d e r
[ D e f r o s t ] C y l i n d e r
[ W a s h i n g ]
[ B o i l i n g ] C y l i n d e r
‘Regeneration’mode.
‘DEFROST’mode
‘WASH’Mode
Mode of ‘BOILING WATER’
N o w : - 6 . 2 °C / - 6 . 2 °C
S e t : 8 . 0 °C / 8 . 0 °C
R e m a i n : 1 m i n / 1 m i n
N o w : - 6 . 2 °C / - 6 . 2 °C
S e t : 8 . 0 °C / 8 . 0 °C
R e m a i n : 1 m i n / 1 m i n
N o w : 0 . 5 A / 0 . 5 A
H o p p e r : 8 . 0 °C / 7 . 0 °C
D r u m : - 5 . 0 °C / - 4 . 0 °C
N o w : 6 . 2 °C / - 6 . 2 °C
S e t : 60 . 0 °C / 60 . 0 °C
R e m a i n : 1 0 m i n / 1 0 m i n
If the soft ice cream is not used for a long time, then its shape
will be degraded. In this case, you can use the ‘ Regeneration ’
function to make it look better.
Press the ‘ DEFROST ’ + ‘ AUTO ’ button at the same time for
more than 2seconds, the status display window shown in the
right gure will appear.
※Caution: Activated under the operation conditions only.
Use the
‘ DEFROST ’ function to melt the soft ice cream
in the cylinder.
It is used to operate the impeller of the hopper and the
dasher motor of the cylinder. Mainly, the Washing function
is used to remove the water or the liquid raw material.
④ : It displays the present current value of the dasher motor
Heat the raw material or water in the cylinder and the
hopper to reach the set temperature in order to wash with
hot water. Press both ‘ DEFROST ’ + ‘ WASH ’ buttons for
longer than 1seconds to display the state window shown in
the picture on the right.
After the current temperature
(⑥)
reaches the set temperature
(⑤)
, when the retention time
(⑦)
passes,
the operation halts.
① : It displays the current temperature of the soft ice cream.
⑤ : The set temperature of the cylinder is displayed.
② : It displays the temperature setting of the cylinder.
⑥ : The current soft ice cream temperature is displayed.
③ : It displays the duration of time (by minute) to maintain the set temperature(②) after the current temperature(①)
reaches the set temperature.
As the duration of the temperature(③) maintenance expires after the current temperature(①) reaches
the target temperature(②), it will automatically enter into 'AUTO' mode to make soft ice cream.
⑦ : The retention time (minutes) is displayed, after the current
temperature(⑥) reaches the set temperature(⑤).
The ‘Regeneration’ function refers to a process where the soft ice cream is liquidized and then
Process of producing soft ice cream; operable in "AUTO" mode only. It takes about 20 to 30 minutes.
⑤
⑥
⑦
④
②
③
①
For your
information