Icom FP-561 User manual

INTRODUCTION
DANGER
ORDERING PARTS
REPAIR NOTES
This service manual describes the latest service information
for the FP-561 MARINE PLOTTER/SOUNDER and RD-200
DGPS BEACON RECEIVER at the time of publication.
To upgrade quality, all electrical or mechanical parts and
internal circuits are subject to change without notice or
obligation.
VERSION
MODEL
FP-561 General
Europe
SYMBOL
GEN
EUR
NEVER connect the unit to an AC outlet or to a DC power
supply that uses more than 33 V (FP-561) or 16 V (RD-200).
Such a connection could cause a fire hazard and/or electric.
DO NOT expose the unit to rain, snow or any liquids.
DO NOT reverse the polarities of the power supply when
connecting the unit.
DO NOT apply an RF signal of more than 20 dBm (100mW)
to the antenna connector. This could damage the unit’s front
end.
Be sure to include the following four points when ordering
replacement parts:
1. 10-digit order numbers
2. Component part number and name
3. Equipment model name and unit name
4. Quantity required
<SAMPLE ORDER>
0910051392 PCB B-5305 FP-561 MAIN UNIT 1 pieces
8810004540 Screw BiH 3x8 SUS FP-561 Chassis 10 pieces
Addresses are provided on the inside back cover for your
convenience.
1. Make sure a problem is internal before disassembling
the unit.
2. DO NOT open the unit until the unit is disconnected from
its power source.
3. DO NOT force any of the variable components. Turn
them slowly and smoothly.
4. DO NOT short any circuits or electronic parts. An insulat-
ed turning tool MUST be used for all adjustments.
5. DO NOT keep power ON for a long time when the unit is
defective.
6. READ the instructions of test equipment thoroughly
before connecting equipment to the unit.
FP-561 RD-200
fineline6

TABLE OF CONTENTS
SECTION 1 SPECIFICATIONS
1-1 FP-561 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1-2 RD-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
SECTION 2 INSIDE VIEWS
2-1 FP-561 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2-2 RD-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
SECTION 3 CIRCUIT DESCRIPTION
3-1 TRANSMITTER CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
3-2 RECEIVER CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
3-3 REGULATOR CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
3-4 INTERFACE CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3-5 LOGIC CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3-6 DGPS RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3-7 PORT ALLOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
SECTION 4 ADJUSTMENT PROCEDURES
4-1 PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4-2 FP-561 TRANSMITTER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4-3 FP-561 RECEIVER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4-4 FP-561 WATER TEMPERTUREM ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4-5 RD-200 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
SECTION 5 PARTS LIST
SECTION 6 MECHANICAL PARTS AND DISASSEMBLY
SECTION 7 SEMI-CONDUCTOR INFORMATION
SECTION 8 BOARD LAYOUTS
8-1 FP-561
8-1-1 SW UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8-1-2 LOGIC UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
8-1-3 MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
8-2 RD-200
8-2-1 MAIN UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-7
8-2-2 ANT UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
SECTION 9 BLOCK DIAGRAM
9-1 FP-561 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9-2 RD-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2
SECTION 10 VOLTAGE DIAGRAM
10-1 FP-561 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
10-2 RD-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3
fineline6

1-1 FP-561
‘GENERAL
• Display : 5.6 inch TFT color LCD (320×234 pixels)
•Power supply requirement : 11–30 V DC
•LCD brightness : 16 levels
•Power consumption : Less than 22 W (Less than 1.8 A at 12 V DC)
•Dimensions (projections not included) : 186(W)×203(H)×102(D) mm; 75⁄16(W)×8(H)×4(D) in
•Weight (approx.) : 2.2 kg; 4 lb 14 oz
•Usable temperature range : 0˚C to +50˚C; +32˚F to +122˚F
•Unit of water depth : m (meter), FT (feet), FM (fathom)
•Unit of water temperature : ˚C, ˚F
•Unit of speed : KT (knots), km/h, MI/h (miles/h)
•Unit of distance : NM (nautical miles), km, MI (miles)
•Input data format : NMEA0183, Water temp./speed, DGPS
•Output data format : NMEA0183 (GGA, GLL, XTE, AAM, VTG, BOD, WPL, BWC),
Start-stop serial forward; 4800 bps
‘GPS
•Receive system : 12 parallel-channel, all-in-one view
•Receive frequency : 1575.42 MHz (±1 MHz)
•Measuring accuracy (2DRMS) : Position 100 m, 95% of the time, PDOP≤3 (Less than 100 m, S/A OFF)
Speed Less than 1 m/sec. (PDOP≤3, S/A ON)
NOTE: All GPS receivers are subject to degradation of position and velocity accuracy under the U.S. Department of
Defence.
•Data renewed interval : 1 sec.
‘PLOTTER
•Scale setting : 16 steps
•Plotting interval : 5 sec. to 60 min., 0.01–9.99 NM*
•No. of track memories : 5000 (selectable from 7 colors)
•No. of route memories : 20 (50 points/route)
•No. of event markers : 500
•Navigation computer : Vessel position (longitude/latitude), cursor position, distance, elapsed time,
course-out distance, direction, distance, time
•Data indication : Coastline, place name, contour line, route, lighthouse, longitude/latitude line
•Alarm : Area and Arrival alarms
1 - 1
SECTION 1 SPECIFICATIONS
fineline6

1 - 2
All stated specifications are subject to change without notice or obligation.
‘VIDEO SOUNDER
•Transmission freq. : 50 kHz, 200 kHz
•Output power : 500 W RMS
•Water depth range : 5–640 m* in 8-color indication
•Water temp. range : 0˚C to +40˚C; +32˚F to +104˚F
•Speed range : 0.0–99.9 KT*
•Bottom lock expansion range : 5 m*, 10 m*, 20 m*, 40 m*
•Phase shift variable range : 1–640 m*
•Type of display screen : Standard, A-scope, dual frequencies, bottom and marker zoom
•Picture sweep speed : 6 levels including pause
•Alarm : Shallow, depth and fish school
*selectable in each unit
1-2 RD-200
‘GENERAL
•Frequency coverage : 283.5 kHz to 325.0 kHz
•Type of emmision : 1K0F2B
•Antenna impedance : 50 Ωnominal
•Intermediate frequency : 455 kHz
•Usable temperature range : –20˚C to +70˚C; –4˚F to +158˚F
•Power supply requirement : 12 V DC nominal negative ground
•Current drain (at 12 V DC) : Less than 0.2 A
•Dimensions (projections not included) : 140(d)×157.2(H) mm; 51⁄2(d)×63⁄16(H) in
•Weight : 1.0 kg; 2 lb 3 oz
‘RECEIVER
•Intermediate frequency : 455 kHz
•Sensitivity : 0.2 µV at 12 dB SINAD
•Sprious response : 60 dB
•Intermodulation : 50 dB
fineline6

2 - 1
SECTION 2 INSIDE VIEWS
2-1 FP-561
• MAIN UNIT
• LOGIC UNIT
+5V regulator
(IC13: PQ05RF21)
GPS receiver
Switching control
(IC9: UPC494GS)
12V rectifier
(D13: SB30-09J)
8V rectifier
(D22: SB30-09J)
+6V regulator
Q27: 2SD1664 Q
D37: RD7.5M B1
40V rectifier
(D12: RG-2A)
Power amplifier
Q6, Q7: FS30KMJ-3
Q23, Q24: 2SC3326-B
Driver
IC2: TC4093BF
Q2, Q3: 2SC2712-GR
Q4, Q5: 2SA1162-GR
STC circuit
Q1: 2SC3326-B
Q26: 2SC2712-GR
200 kHz local oscillator circuit
IC3: TC3W03FU
X1: CR-497 (5.24MHz)
50 kHz local oscillator circuit
IC4: TC3W03FU
X2: CR-496 (4.04MHz)
Crystal oscillator
(X1: DSO-49SJ)
Main CPU
(IC1: CL-PS7500FE)
FIFO RAM
(IC20: CY7C433-40JC)
DRAM
(IC34, IC35: M5M44260CJ) SRAM
(IC30, IC31: M5M51008BVP-70LL)
Flash ROM
(IC32, IC33: MBM29F800BA-90PFTN)
Sub CPU
(IC22: TMP90PM36F)
Mail box RAM
(IC21: M66220FP)
DC-DC converter
Q4: 2SB120IS
Q5: XP6501AB
fineline6
Other manuals for FP-561
2
Table of contents
Other Icom Receiver manuals

Icom
Icom COMMUNICATIONS RECEIVER IC-R3 User manual

Icom
Icom COMMUNICATIONS RECEIVER IC-R3 User manual

Icom
Icom IC-R100 User manual

Icom
Icom IC-RX7 User manual

Icom
Icom IC-R30 User manual

Icom
Icom IC-R30 Installation guide

Icom
Icom IC-R100 User manual

Icom
Icom IC-R7100 User manual

Icom
Icom IC-A25N Installation guide

Icom
Icom IC-R72 User manual