Icom IC-F6062D User manual

OPERATING GUIDE
OPERATING GUIDE FOR
IC-F5062D/F6062D
BIIS 1200/dPMR OPERATION

i
Thank you for purchasing this Icom transceiver.
The Binary Interchange of Information and Signalling (BIIS)
1200 and digital Private Mobile Radio (dPMR) system func-
tions are built into your IC-F5062D/F6062D transceiver.
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS OPERATING GUIDE — This guide con-
tains important operating instructions for:
• IC-F5062D v h f dp m r m o b i l e t r a n s c e i v e r
• IC-F6062D u h f dp m r m o b i l e t r a n s c e i v e r
NOTE: In this operating guide, the LCD illustration is
shown as having characters displayed in 2 lines.
INFORMATION: The 10-keypad of the optional HM-148T
DTMF microphone has only the DTMF code transmitting
capability, so you cannot input any ID or message with
this microphone.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
All other products or brands are registered trademarks or trademarks of their
respective holders.
IMPORTANT

TABLE OF CONTENTS
ii
IMPORTANT.......................................................................... i
TABLE OF CONTENTS........................................................ ii
1 PREPARATION............................................................1–2
 ■ Programmable function keys ........................................1
2 BIIS 1200 OPERATION .............................................3–12
 ■ BIIS 1200 operation......................................................3
 ■ BIIS display ..................................................................3
 ■ Receiving a call ............................................................3
 ■ Transmitting a call.........................................................7
 ■ Position data transmission..........................................11
 ■ Stun function ..............................................................11
 ■ BIIS ANI .....................................................................11
 ■ Horn output ................................................................12
 ■ Printer connection ......................................................12
3 dPMR OPERATION.................................................13–27
 ■ dPMR operation .........................................................13
 ■ dPMR display .............................................................13
 ■ Receiving a call ..........................................................13
 ■ Transmitting a call.......................................................18
 ■ Transmitting a command ............................................24
 ■ Position data transmission..........................................26
 ■ Status message transmission ....................................26
 ■ Horn output ................................................................27
 ■ Printer connection ......................................................27

1
1PREPARATION
■Programmable function keys
The following functions can be assigned to [UP], [DOWN],
[P0], [P1], [P2], [P3] and [P4] programmable function keys.
Consult your Icom dealer or system operator for details con-
cerning your transceiver’s programming.
If the programmable function names are bracketed in the fol-
lowing explanations, the specific key is used to activate the
function.
DFor only BIIS 1200 operation
The following key function is required for BIIS 1200 operation.
BIIS BUTTON
➥Push to enter the call code memory mode.
• Push [CH Up] or [CH Down] to select a desired Individual or
Group ID.
➥While in the call code memory mode, push to enter the
message selection mode.
• Push [CH Up] or [CH Down] to select a desired status message
or Short Data Message (SDM).
➥ While in the message selection mode, push to return to the
stand-by mode.
➥Hold down for 1 second to toggle between the memory
channel mode and the queue channel mode.
➥While in the queue channel mode, push to toggle between
the queue channel mode and the received message
mode.
“”
appears above the key assigned to the BIIS Button
function, when it is activated.
DFor only dPMR operation
The following key functions are required for dPMR operation.
dPMR BUTTON
➥Push to enter the ID selection mode.
• Push [CH Up] or [CH Down] to select a desired Individual or
Talkgroup ID.
➥While in the ID selection mode, push to enter the application
selection mode.
• Push [CH Up] or [CH Down] to select a desired application from
“STATUS,” “MESSAGE,” “STAT POL,” “LISTENING,” “STUN,”
“KILL,” “REVIVE” and “CALL LOG.”
➥If you select “STATUS” or “MESSAGE”in the application selec-
tion mode, push to enter the message selection mode.
• Push [CH Up] or [CH Down] to select a desired message.
➥ While in the application selection mode, push to return to
the stand-by mode.
CLEAR
After communication is finished, push this key to send a ‘Dis-
connect’ signal to terminate the connection.
Depending on the pre-programmed settings, the Priority A
channel is automatically selected after a ‘Disconnect’ sig-
nal terminates a connection.

DFor BIIS 1200 and dPMR operations
The following key functions are useful for both BIIS 1200 and
dPMR operations.
STATUS UP, STATUS DOWN
➥Push to select a status message.
➥When the automatic scroll function is activated, push to
cancel it, if desired.
➥When an SDM that includes more than 12 characters is
displayed, push to manually scroll the message.
STATUS
➥Push to enter the status message selection mode.
• Push [CH Up] or [CH Down] to select a desired message.
➥Hold down for 1 second to transmit the last selected status
message.
MESSAGE
➥Push to enter the SDM selection mode.
• Push [CH Up] or [CH Down] to select a desired SDM.
➥While in the SDM selection mode, hold down for 1 second
to transmit the last selected SDM.
➥While in the stand-by mode, hold down for 1 second to
enter the message editing mode. (dPMR only)
• Set a desired message using the optional HM-152T h a n d m i c r o -
p h o n e (p.22).
In BIIS 1200 operation, status messages and SDM are
selectable in the same mode.
DAdditional key functions
• For BIIS 1200 and dPMR operations
The following key functions are recommended for both BIIS
1200 and dPMR operations, and function as described below.
CALL
➥On an MSK channel, push to transmit a BIIS call.
➥On a digital channel, push to transmit a dPMR call.
Depending on the pre-programmed settings, pushing [PTT]
makes a call in the same way as using [Call]. Moreover,
when you keep holding down [PTT] after receiving an ac-
knowledgement, you can start a conversation without
pushing it again.
TX CODE ENTER
Push to enter the ID code edit mode, and then set a desired
ID code. (pp. 7, 18)
• For only BIIS 1200 operation
The following key function is required for BIIS 1200 operation,
and functions as described below.
MONITOR (AUDIBLE)
After communication is finished, push this key to send a ‘Clear
down’ signal to terminate the connection.
Depending on the pre-programmed settings, the Priority A
channel is automatically selected after a ‘Clear down’ sig-
nal terminates a connection.
2
1
PREPARATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

3
2BIIS 1200 OPERATION
■BIIS 1200 operation
The Binary Interchange of Information and Signalling (BIIS)
1200 standard is the best choice to add a data service to an
existing system. It enables digital communications, signalling
and message exchanges with analog transceivers.
The BIIS system provides calling features such as Individual,
Group, and Emergency calls, as well as enables receiving
and transmitting status messages and SDM.
NOTE: During BIIS 1200 operation, dPMR operation is
disabled.
■BIIS display
The following displays appear in BIIS 1200 operation.
CONNECT : When an acknowledgement of an Individual or
Group call is received.
OK : When an acknowledgement of a message (sta-
tus message or SDM) is received.
FAILED : When no acknowledgement of a call is re-
ceived.
WAIT : While transmitting.
CLR DOWN : When a connection is terminated.
BUSY : When the operating channel is busy.
■Receiving a call
DReceiving an Individual call
q When an Individual call is received:
• Rings sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the pre-programmed set-
tings.
• Your own ID (or name) and the calling station’s ID (or name)
blink.
0001
1234
Appears or blinksAppears
Your own ID Calling station’s ID
w While holding down [PTT], speak into the microphone at
your normal voice level.
e Release [PTT] to receive.
r After the communication is finished, push [Moni (Audi)] to
send a ‘Clear down’ signal to terminate the connection.
• Either you or the calling station can send a ‘Clear down’ signal.
• “ ” disappears, “CLR DOWN” appears for approximately 2
seconds, and the transceiver automatically returns to the
stand-by mode.

4
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DReceiving a Group call
qWhen a Group call is received:
• Rings sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the pre-programmed set-
tings.
• The group ID (or name) and the calling station’s ID (or name)
blink.
4001
1234
Appears or blinksAppears
Group ID Calling station’s ID
wWhile holding down [PTT], speak into the microphone at
your normal voice level.
NOTE: Only one station is allowed to speak at the same
time.
eRelease [PTT] to receive.
r After the communication is finished, push [Moni (Audi)] to
send a ‘Clear down’ signal to terminate the connection.
• Either station can send a ‘Clear down’ signal.
• “ ” disappears, “CLR DOWN” appears for approximately 2
seconds, and the transceiver automatically returns to the
stand-by mode.
DReceiving an Emergency call
qWhen an Emergency call is received:
• Rings sound.
• “Emergency” and the calling station’s ID (or name) blink.
• The transceiver automatically transmits an acknowledgement to
the calling station.
Emergency
1111
Calling station’s ID
wPush [Moni (Audi)] to return to the stand-by mode.

5
2BIIS 1200 OPERATION
DReceiving a status message
qWhen a status message is received:
• Rings sound.
• The calling station’s ID (or name) and the status message blink.
RX Status 01
1234
The received
status message
Calling station’s ID
wPush [Moni (Audi)] to return to the stand-by mode.
NOTE: When the display mode is 1 line
If the ‘Scroll Timer’ item is set to “OFF,” even when a status
message is received, only the calling station’s ID (or name)
is displayed (no message is alternately displayed). In that
case, push [Status Down] to display the status message
manually.
DReceiving an SDM
qWhen an SDM is received:
• Rings sound.
• “ ” appears.
• The calling station’s ID (or name) and the SDM blink.
SDM8
1234
Appears
Calling station’s ID
The received
SDM
NOTE: When the SDM includes more than 12 charac-
ters, it automatically scrolls.
• Push [Status Up] or [Status Down] to stop scrolling, or
manually scroll the message.
RETURN FICETO OF
1234
Scrolls
wPush [Moni (Audi)] to return to the stand-by mode.

6
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DDisplaying a received call record
— Queue channel mode
The transceiver memorizes up to 3 calling station’s IDs. When
the 4th call is received, the oldest call record will be removed,
and the last received call will be added. When the transceiver
is turned OFF, all the records are deleted.
qHold down [BIIS Button] for 1 second to enter the queue
channel mode.
• The screen display varies as shown below.
When the transceiver has a call record
<QUEUE>
-QUEUE!-
When the transceiver has no call record
<QUEUE>
NO QUEUE
wPush [CH Up] or [CH Down] to display a desired record.
eHold down [BIIS Button] for 1 second again to return to
the stand-by mode.
• When no operation occurs for 30 seconds, the transceiver auto-
matically returns to the stand-by mode.
NOTE: You can call back from the queue channel record.
While displaying an ID, push [Call] to make a call using
the selected ID.
DDisplaying a received message
The transceiver memorizes up to 6 received messages. When
the 7th message is received, the oldest message will be re-
moved, and the last received message will be added. When
the transceiver is turned OFF, all the messages are deleted.
qHold down [BIIS Button] for 1 second to enter the queue
channel mode.
wPush [BIIS Button] momentary to enter the received mes-
sage mode.
• The screen display varies as shown below.
When the transceiver has a message record
MESSAGE
-MSG!-
When the transceiver has no message record
MESSAGE
-NOMSG-
ePush [CH Up] or [CH Down] to display a desired mes-
sage.
rHold down [BIIS Button] for 1 second again to return to
the stand-by mode.
• When no operation occurs for 30 seconds, the transceiver auto-
matically returns to the stand-by mode.

7
2BIIS 1200 OPERATION
■Transmitting a call
DGeneral
• Editing an ID
If the transceiver has a key assigned to the TX Code Enter
function, you can edit an ID within the allowable digits.
qPush [TX Code Enter] to enter the ID edit mode.
• The digit to be edited blinks.
wPush [TX Code Enter] to select a desired digit to be ed-
ited.
ePush [CH UP] or [CH DOWN] to select a desired number.
rPush [TX Code Enter] to set. The digit to the right will au-
tomatically blink.
tRepeat step eand rto input all allowable digits.
yAfter editing, push [TX Code Enter] to store the setting.
• The transceiver returns to the standby mode.
NOTE: To overwrite the original ID, set the ‘Update’ item to
“Enable” using the CS-F3160/F5060 (dPMR) cloning
software.Otherwise, changing the channel or turning
OFF the transceiver discards the new ID, and returns the
original one. Ask your dealer for details.
DTransmitting an Individual or Group call
NOTE: If you want to make a call to the pre-programmed
ID, skip step qand w, then directly go to step e.
qPush [BIIS Button] to enter the call code memory mode.
• The pre-programmed ID is displayed.
• “ ” appears.
wPush [CH Up] or [CH Down] to select a desired Individual
ID or Group ID.
ePush [Call] to make a call.
• “WAIT” appears while transmitting.
• “ CONNECT” is displayed when an acknowledgement is received.
NOTE: If no acknowledgement is received, the trans-
ceiver automatically repeats the call 3 times (default).
However, when no acknowledgement is received after
each of the calls, an error beep sounds and “FAILED”
is displayed. In that case, the transceiver automatically
returns to the stand-by mode.
rAfter “CONNECT” is displayed, hold down [PTT] and
speak into the microphone at your normal voice level. Re-
lease [PTT] to receive.
tAfter the communication is finished, push [Moni (Audi)] to
send a ‘Clear down’ signal to terminate the connection.
1234
Appears

8
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DTransmitting a status message
You can send a pre-programmed status message to an indi-
vidual station or to group stations.
There are 24 status messages that can be sent, and Status
22 and 24 messages have designated meanings.
Status 22: Emergency
Status 24: GPS request
• Status 22 can also be used as a normal status message by
disabling the designated meaning. However, Status 24 is fixed.
NOTE: Depending on the pre-programmed settings, the
Priority A channel is always used to send status mes-
sages.
qPush [BIIS Button] to enter the call code memory mode.
• “ ” appears.
• The pre-programmed ID is displayed.
wPush [CH Up] or [CH Down] to select a desired Individual
ID or Group ID.
ePush [BIIS Button] again to enter the message selection
mode, then push [CH Up] or [CH Down] to select a de-
sired status message.
STATUS 01
TX Status 01
A status message is displayed.
rPush [Call] to transmit the status message to the selected
station or group.
• “WAIT” is displayed while transmitting.
• “OK” is displayed when an acknowledgement is received.
• “FAILED” is displayed when no acknowledgment is received.
tAfter a specified time period, the transceiver will return to
the stand-by mode.

9
2BIIS 1200 OPERATION
DTransmitting an SDM
You can send a pre-programmed SDM to an individual station
or to group stations.
The transceiver has 8 memories to store messages.
qPush [BIIS Button] to enter the call code memory mode.
• “ ” appears.
• The pre-programmed ID is displayed.
wPush [CH Up] or [CH Down] to select a desired Individual
ID or Group ID.
ePush [BIIS Button] again to enter the message selection
mode, then push [CH Up] or [CH Down] to select a de-
sired SDM.
• “ ” appears.
MESSAGE1
SDM1
An SDM is displayed.
Appears
rPush [Call] to transmit the SDM to the selected station or
group.
• “WAIT” is displayed while transmitting.
• “OK” is displayed when an acknowledgement is received.
• “FAILED” is displayed when no acknowledgment is received.
tAfter a specified time period, the transceiver will return to
the stand-by mode.
DDirect message input
While displaying an SDM, you can edit or change the mes-
sage using the optional HM-152T h a n d m i c r o p h o n e .
qPush [BIIS Button] twice to enter the message selection
mode, then push [CH Up] or [CH Down] to select a de-
sired SDM.
• “ ” appears.
wPush [M]or [#] to enter the message editing mode.
• The first character blinks when [#] is pushed, the last character
blinks when [M]is pushed.
• “ ” blinks.
ePush the appropriate digit key, [0] to [9], to enter a desired
character.
• See the table on the next page for the usable characters.
• Push [CH Up] to enter a space, and push [CH Down] to delete
the selected character.
rPush [#] to move the cursor to the right, push [M]to move
the cursor to the left.
tRepeat steps eand rto enter a message of up to 12
characters.
yHold down [BIIS Button] for 1 second to write the new
programmed message into the SDM memory.
• Push [BIIS Button] momentarily to cancel editing and return to
the original message display.

10
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
• Usable characters
Key
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
Characters
0 ! ? ' " , ; : _ ( ) < > [ ]
1 (space) # * / + - = & % $ @ ^
2 A B C a b c
3 D E F d e f
4 G H I g h i
5 J K L j k l
6 M N O m n o
7 P Q R S p q r s
8 T U V t u v
9 W X Y Z w x y z
/
!
NOTE: Messages can be edited also using a PC editing
program. Ask your dealer for details.
DTransmitting an Emergency call
If an MSK channel is used as the Emergency channel, the
transceiver can access the BIIS emergency mode.
If your transceiver is programmed for Silent operation, you
can transmit Emergency calls without the beep sounding or
the display changing.
qHold down [Emergency] for the pre-programmed time pe-
riod to enter the emergency mode.
• Countdown beeps start.
• To exit the emergency mode, hold down [Emergency] for the
pre-programmed period before the end of the count-down time
period.
wWhen the time period ends, the transceiver automatically
starts an Emergency call cycle, once or repeatedly, de-
pending on the pre-programmed repeat cycle setting.
eIn an Emergency call cycle, the transceiver automatically
transmits Status 22 (Emergency) to inform the dispatcher
that the user is in an emergency situation.
• “WAIT” appears while transmitting.
• “OK” is displayed when an acknowledgement is received.
• “FAILED” is displayed when no acknowledgment is received.
NOTE: Depending on the pre-programmed settings,
the transceiver does not transmit Status 22 in the re-
peated cycles.
rAfter the Emergency call cycles have ended, the trans-
ceiver automatically returns to the stand-by mode.
• To exit the emergency mode manually, turn OFF the power, and
turn ON it again.

11
2BIIS 1200 OPERATION
■Position data transmission
When a GPS receiver is connected to the transceiver, the
position data (longitude and latitude) can be automatically
transmitted. Ask your dealer or system operator for connec-
tion details.
The position data is transmitted:
• When Status 24 (GPS request) is received.
• When [PTT] is released.
- Set the ‘Send with Logoff’ item to “Enable.”
• After sending a status message.
- Set the ‘Send with Status’ item to “Enable.”
• After sending an SDM.
- Set the ‘Send with SDM’ item to “Enable.”
• After sending Status 22 (Emergency).
- Set the ‘Send with Emergency’ item to “Enable.”
• By the Automatic Position Transmission function.
When the function is activated, the transceiver auto-
matically transmits position data according to the ‘Time
Marker’ and ‘Interval Timer’ settings.
- Set the ‘Auto’ item to “Enable.”
NOTE: Configure the position data transmission settings
using the CS-F3160/F5060 (dPMR) c l o n i n g s o f t w a r e .
Ask your dealer for details.
■Stun function
If a call is received with a specified ID, set as the killer ID, the
stun function is activated and the transceiver is disabled. In
that case, entering the password is necessary to reactivate
the transceiver.
■BIIS ANI
Your own ID can be transmitted each time [PTT] is pushed
(log-in) or released (log-off) during Individual or Group call
communications.
By receiving an ANI, the communication log can be recorded
when using a PC dispatch application.
In addition, when using the ANI with the Log-in function, the
PTT Side Tone function can be used to inform you that the ID
is sent and communication can begin.

12
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■Horn output
When a horn is connected to the D-Sub 25-pin connector of
the transceiver, the Automatic Honking function is usable, de-
pending on the pre-programmed settings.
When a status message is received, the transceiver controls
the vehicle’s horn to sound an alert for the pre-programmed
time period.
This function is useful when you are away from the trans-
ceiver.
Ask your dealer or system operator for connection and set-
ting details.
■Printer connection
When a printer is connected to the D-sub 25-pin connector of
the transceiver, received SDM and the calling station’s ID can
be printed out, depending on the pre-programmed settings.
Ask your dealer or system operator for connection and set-
ting details.

13
3dPMR OPERATION
13
■dPMR operation
The IC-F5062D and IC-F6062D provide digital Private Mobile
Radio (dPMR) operation that meets the 6.25 kHz bandwidth
requirements for narrow band operation. This increases ef-
ficiency of channel allocation and use of the spectrum.
NOTE: During dPMR operation, BIIS 1200 operation is
disabled.
■dPMR display
The following displays appear in dPMR operation.
CONNECT : When an acknowledgement of a Voice or Emer-
gency call is received.
OK : When an acknowledgement of a message (sta-
tus message or SDM) or command (Ambience
Listening, Stun, Kill, or Revive) is received.
FAILED : When no acknowledgement of a call is re-
ceived.
WAIT : While transmitting.
CLR DOWN : When a connection is terminated.
ID : When no name is programmed, appears to the
left of the calling station’s ID.
TG : When no name is programmed, appears to the
left of the Talkgroup ID.
■Receiving a call
DReceiving an Individual call
qWhen an Individual call is received:
• Rings sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the pre-programmed set-
tings.
• The calling station’s ID (or name) blinks.
ID 0000001
Calling station’s ID
Appears or blinksAppears
wWhile holding down [PTT], speak into the microphone at
your normal voice level.
eRelease [PTT] to receive.
rAfter the communication is finished, push [Clear] to send
a ‘Disconnect’ signal to terminate the connection.
• Either station can send a ‘Disconnect’ signal.
• “ ” disappears, “CLR DOWN” appears for approximately 2
seconds, and the transceiver automatically returns to the
stand-by mode.

14
3
dPMR OPERATION 3
16
15
14
13
12
11
10
9
8
7
6
5
4
2
1
14
DReceiving a Group call
qWhen a Group call is received:
• Rings sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the pre-programmed set-
tings.
• The Talkgroup ID (or name) and the calling station’s ID (or name)
blink.
• When an All Call is received, “ALL CALL” blinks instead of “TG”
and the Talkgroup ID.
TG 0100000
ID 0000001
Calling station’s IDTalkgroup ID
Appears or blinksAppears
wWhile holding down [PTT], speak into the microphone at
your normal voice level.
NOTE: Only one station is allowed to speak at the
same time.
eRelease [PTT] to receive.
rAfter the communication is finished, push [Clear] to send
a ‘Disconnect’ signal to terminate the connection.
• Either station can send a ‘Disconnect’ signal.
• “ ” disappears, “CLR DOWN” appears for approximately 2
seconds, and the transceiver automatically returns to the
stand-by mode.
DReceiving a status message
qWhen a status message is received:
• Rings sound.
• The calling station’s ID (or name) and the status message
blink.
RX STATUS 01
ID 0000001
The received
status message
Calling station’s ID
wPush [Clear] to return to the stand-by mode.

15
3dPMR OPERATION
DReceiving an SDM
qWhen an SDM is received:
• Rings sound.
• “ ” appears.
• The calling station’s ID (or name) and the SDM are displayed.
Message1
ID 0000001
The received
SDM
Appears
Calling station’s ID
NOTE: When the SDM includes more than 12 charac-
ters, it automatically scrolls.
• Push [Status Up] or [Status Down] to stop scrolling, or
manually scroll the message.
RETURN FICETO OF
ID 0000001
Scrolls
wPush [Clear] to return to the stand-by mode.
DReceiving a Stun, Kill or Revive call
If an Individual call with a Stun or Kill command is received
from a specied station, the transceiver will display “SORRY,”
and becomes unusable.
NOTE: If the transceiver receives a Stun, Kill, or Revive
command from a station other than the specified ones, the
call will be ignored, and the transceiver will not be stunned,
killed, or revived.
➥When a Stun command is received, the transceiver is
disabled*1. In that case, receiving a Revive command or
inputting the password*2is necessary to operate the trans-
ceiver again.
*
1Depending on the pre-programmed settings, receiving a Stun
command inhibits only transmission, but the transceiver still
can receive.
*
2Depending on the pre-programmed settings.
➥When a Kill command is received, the transceiver is disa-
bled. In that case, re-programming the transceiver is nec-
essary to operate the transceiver again.
DReceiving a Status Polling call
If a Status Polling call is received, the transceiver will auto-
matically transmit its current status.

3
dPMR OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16
DReceiving an Ambience Listening call
If an Individual call with an Ambience Listening command is
received from a specified station, the transceiver will auto-
matically transmit its microphone audio.
• The HM-148G or HM-152 HAND MICROPHONE is required.
NOTE: If the transceiver receives an Ambience Listening
command from a station other than the specified one, the
call will be ignored, and the transceiver will not transmit its
microphone audio.
DReceiving an Emergency call
qWhen an Emergency call is received:
• Rings sound.
• “ Emergency” and the channel number* are alternately displayed.
* Depending on the pre-programmed settings, the calling station’s
ID (or name) can be displayed.
• The transceiver automatically transmits an acknowledgement to
the calling station.
Emergency
001ch-01
wPush [Clear] to return to the stand-by mode.
DTalk back function
The Talk Back function allows you to select the same call
mode (Analog or Digital) as the received call.
If the received call is a digital signal, the Talk Back function is
activated for Voice and Emergency calls, and depending on
the pre-programmed settings, also for status messages and
SDM.
When the channel type is “Mixed-Digital”
After receiving an analog signal, “ANALOG” is displayed
during the Talk Back timer period, depending on the pre-pro-
grammed settings. When [PTT] is pushed before or during the
Talk Back timer period, you can transmit an analog signal.
When the channel type is “Mixed-Analog,”“Mixed-Digital”
or “Digital”
After receiving a digital signal, the calling station’s ID or the
Talkgroup ID is displayed until receiving a ‘Disconnect’ sig-
nal, depending on the pre-programmed settings. Even on a
“Mixed-Analog” channel, when [PTT] is pushed before re-
ceiving a ‘Disconnect’ signal, the Talk Back function allows
the transceiver to transmit a digital signal to the ID.
NOTE: When this function is not activated, the transceiver
always transmits analog signals on “Mixed-Analog” chan-
nels, and digital signals on “Mixed-Digital” channels.
• On these channels, the transceiver can receive both analog and
digital signals, regardless of the Talk Back function.

17
3dPMR OPERATION
DDisplaying a received call log entry
Depending on the pre-programmed setting, the transceiver
stores up to 10 call log entries. Individual Voice, Status and
SDM call log entries are stored. When an 11th call is re-
ceived, the oldest call log entry will be removed, and the last
received call will be added. When the transceiver is turned
OFF, all the log entries are deleted.
qPush [dPMR Button] twice to enter the application selec-
tion mode.
• “STATUS” appears.
w Push [CH Up] or [CH Down] to select “CALL LOG.”
ePush [
dPMR Button] again to display a call log entry.
When the transceiver has a call log entry
VOICE
0000001
When the transceiver has no call log entries
NO LOG
rPush [CH Up] or [CH Down] to display a desired entry.
• If a Status or SDM call log entry is selected, not only the calling
station’s ID but also the status message or message are dis-
played.
t Push [dPMR Button] again to return to the stand-by mode.
NOTE: Depending on the pre-programmed settings, push-
ing [Call] while displaying a call log entry makes a Voice
call using the entry’s ID. However, if a Status or SDM call
log entry is selected, the transceiver makes a Voice call
using the last selected Individual or Talkgroup ID.