ICP DAS USA tZT-P4C4 User manual

Technical support: [e-mail] P1
tZT-P4C4 Quick Start
v1.0, February. 2018
1 What’s in the box?
Without “Quick Start”, The package includes the following items:
tZT-P4C4
Screw Driver
2 Introduction to the Configuration Parameters
1) Pan ID：
group identity for a ZigBee network, and must the same for all devices
in the same ZigBee network. (Setting Range : 0x0000~0x3FFF)
2) Address/Node ID：
distinguish identity of a specific the ZigBee module, and must be
unique for each device connected the same ZigBee network.
(Setting Range : 0x01~0xFF)
3) RF Channel：
indicates the radio frequency channel, and must be set to the same
value as other modules on the same ZigBee network.
Channel
0x00
0x01
……
0x0F
Frequency(MHz)
2405
2410
……
2480
RF channels 0x04, 0x09, 0x0E or 0x0F are recommended because they
do not overlap with the Wi-Fi frequencies based.

Technical support: [e-mail] P2
3 Preparation
1) Turn the switch to “Init”
2) Connect tZT-P4C4 module.
i. Open DCON Utility and use ZT-2000 Coordinator connect
Default Parameter：
Protocol
DCON
CheckSum
Disable
PAN ID
0x1234
Node ID
0x01
RF Channel
0x0E
RF Power
0x07
ii. Use RS-232
3) Power supply range：+10 ~ +30 VDC
4 Communication Test
As the ZigBee network is controlled by the ZigBee coordinator, the
ZT-2550/ZT-2570 (ZigBee coordinator) must be configured first. Please
refer to documents shown below for full details of how to configure these
devices.
Once configuration of the ZigBee coordinator has been completed.
Set the ”Pan ID” and the “RF Channel” values for the tZT-P4C4 to the
same values as the network, and then reboot the device. The module
will automatically start to function on the ZigBee network using the
default protocol.
※ Documents
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/document/zt-255x/
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/document/zt-257x/
※ Configuration Utility (Used to configure ZT-2000 I/O device Coordinator)
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/

Technical support: [e-mail] P3
5 Communication Test
Once the tZT-P4C4 has joined the ZigBee network, the signal quality
can be confirmed by monitoring the status of the ZigBee Net LED
indicators. If the LED indicator shows a steady light, communication with
the tZT-P4C4 has been successfully established for data acquisition and
control.
ICP DAS also provides the “DCON Utility”, which can be used to
simulate DCON/Modbus communication. This software can also be
used to verify the device settings and ZigBee I/O functions.
※ The DCON Utility can be download from:
http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
Simulate I/O channel operating via using DCON Utility
1) Launch DCON Utility and select the correct COM Port settings to
connect the ZigBee Coordinator (ZT-2550/ZT-2570).
2) Clicking “Search” button will start searching which tZT-P4C4 is in
the same ZigBee network.
3) If there is any tZT-P4C4 displayed, double clicking the “module
name” will start the I/O channels operated platform.

Technical support: [e-mail] P4
6 Troubleshooting
1. Technical Support
If you have any difficulties using your tZT-P4C4, please send a
description of the problem to servi[email protected] Include the
following items in your email:
A. Set the DIP switch of the ZT-255x device to the [ZBSET] position
then reboot the device. Launch the ZT Configuration Utility and
select [Save Log] icon to save the configuration of the ZT-255x as
a file.
B. After clicking the [Save Log] icon, enter the “File Name” and the
“File Path” in the Windows “Save” dialog box. Once the
configuration has been successfully saved, the following message
will be displayed.
2. LED Indicator Status:
LED Indicator
Status
Introduction
ZBNet
(Green LED)
ZigBee Coordinator (Master)
Steady Lit
ZigBee Net is set up correctly
Blinking to Steady Lit
Already have same ZigBee
network or rejoin ZigBee network
ZigBee Router (Slave)
Steady Lit
The Signal is Strong
Blinking (500ms)
The Signal is Available
Blinking (1s)
The Signal is Weak
Blinking (2s)
The Signal is Unstable or There is
no Available
ZigBee PWR
(Red LED)
The status of module board
Steady Lit
The Power is ON and the Module
Initialization is Correct
Blinking (200ms)
Module Initialization Failure
Blinking (1s)
Watchdog is Enabled and the
status of the I/O channel
has been changed to the Safe
Value. Reset the module
via the power switch or
configuration commands.
Steady Unlit
The Power is OFF