ICP DAS USA ISaGRAF mPAC Series User manual

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .1
Getting Started of
μPAC-5007(P)/5107(P)/5207/5307
This manual is intended for integrators, programmers, and maintenance personnel who will be
installing and maintaining a PAC-5x07(P) controller system.
ISaGRAF PAC Series of ICP DAS includes:
μPAC: μPAC-7186EG, μPAC-7186PEG, I-7188EG, I-7188XG,
μPAC-5007/5007P/5107/5107P/5207/5307
iPAC: iP-8447, iP-8847, I-8437-80, I-8837-80, I-8417, I-8817,
WinPAC: WP-8147, WP-8447, WP-8847 (WinCon: W-8347, W-8747)
ViewPAC:VP-25W7, VP-23W7, VP-2117
XPAC: XP-8047-CE6, XP-8347-CE6, XP-8747-CE6
Legal Liability
ICP DAS CO., LTD. assumes no liability for any and all damages that may be incurred by
the user as a consequence of this product. ICP DAS CO., LTD. reserves the right to
change this manual at any time without notice.
ICP DAS CO., LTD. constantly strives to provide our customers with the most reliable and
accurate information possible regarding our products. However, ICP DAS CO., LTD.
assumes no responsibility for its use, or for any infringements of patents or other rights
of third parties resulting from its use.
Trademark & Copyright Notice
The names of products are used for identification purposes only, and are the registered
trademarks of their respective owners or companies.
Technical Service:
Please contact local agent or email problem-report to [email protected].
New information can be found at www.icpdas.com.
Please visit www.icpdas.com > FAQ > Software > ISaGRAF for Frequently Asked Questions.
Written by Chun Tsai, Spike Huang & Janice Hong, R&D dept., ICP DAS
Copyright © May. 2010, by ICP DAS CO., LTD. All Rights Reserved.

2Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
Table of Contents
Getting Started of μPAC-5007(P)/5107(P)/5207/5307 ............................................................. 1
Table of Contents .................................................................................................................... 2
Reference Guide...................................................................................................................... 4
Performance Comparison Table of ISaGRAF PACs .................................................................... 5
Specifications: μPAC-5x07(D)/5x07P(D)................................................................................... 6
Chapter 1. Typical Application ...................................................................................... 1-1
1.1 μPAC-5007 (P)/5107 (P)/5207/5307 Comparison Table.....................................1-1
1.2 Local & Remote I/O Application..........................................................................1-1
1.3 Multi-HMI Application.........................................................................................1-2
1.4 Active Data Acquisition & Auto-Report System..................................................1-2
1.5 Data Logger .........................................................................................................1-3
1.6 Modbus Converter of Remote I/O Modules .......................................................1-3
1.7 Data Exchange through Ethernet or RS-485 .......................................................1-4
1.8 Send Email with an Attached File........................................................................1-4
1.9 SMS: Short Message Service ...............................................................................1-5
1.10 Integrate with CAN/CANopen Devices and Sensors ...........................................1-5
1.11 Connecting other Device via Modbus Master ....................................................1-6
1.12 GPS Applications: ISaGRAF PAC plus I-87211W or GPS-721...............................1-7
1.13 ZigBee Wireless Solution.....................................................................................1-8
Chapter 2. Software Programming................................................................................ 2-1
2.1 Step 1 –Installing ISaGRAF Software ..................................................................2-1
2.2 Step 2 –Installing ICP DAS Utilities for ISaGRAF .................................................2-4
Chapter 3. Hardware System & Setting ......................................................................... 3-1
3.1 Connect Your PC to COM1 Port...........................................................................3-1
3.2 Connect Your PC to COM2 Port...........................................................................3-2
3.3 Connect Your PC to Ethernet Port.......................................................................3-3
3.4 How to Update Hardware Driver ........................................................................3-5
3.5 Set NET-ID for Controller System ........................................................................3-8
3.6 Set Baud Rate for COM1 .....................................................................................3-9
3.7 Set COM1 to Non-Modbus-Slave for μPAC-5x07(P) .........................................3-10
3.8 Set COM2 or COM3 as a Modbus RTU Slave Port.............................................3-12
3.9 Set IP & MASK & Gateway for μPAC-5x07(P)....................................................3-14
3.10 Delete an ISaGRAF Project from the PAC..........................................................3-16

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .3
3.11 Set I-7000 and I-87K Remote I/O by DCON Utility ............................................3-17
3.12 Link to I-7000 and I-87K Remote I/O Modules .................................................3-21
3.13 Create Two Modbus Master/Slave Links ..........................................................3-22
3.14 Link to HMI Interface Device.............................................................................3-23
3.15 Backup & Restore an ISaGRAF Project ..............................................................3-24
3.16 Dimension & Mounting for μPAC-5x07(P) ........................................................3-25
Chapter 4. ISaGRAF Demo............................................................................................. 4-1
4.1 Writing a Simple ISaGRAF Program.....................................................................4-1
4.1.1: Start ISaGRAF –Project Management......................................................4-2
4.1.2: Creating an ISaGRAF Project Group .........................................................4-2
4.1.3: Creating a New ISaGRAF Project ..............................................................4-3
4.1.4: Declaring the ISaGRAF Project Variables..................................................4-4
4.1.5: Creating the Example LD Program ...........................................................4-8
4.1.6: Editing the Example "LD1" Program.........................................................4-9
4.1.7: Connecting the I/O .................................................................................4-12
4.2 Step 4 –Compiling & Simulating the Example Project .....................................4-15
4.2.1: Compiling the LD Project!.......................................................................4-15
4.2.2: Simulating the LD Project .......................................................................4-16
4.2.3: Running the Simulation Program: ..........................................................4-17
4.3 Step 5 –Debug & Download the Example Project............................................4-20
Appendix................................................................................................................................. 1
A. ISaGRAF User Manual & Demo Program & FAQ ....................................................1
A.1 The Download Page for ISaGRAF Resource.................................................1
A.2 Using Modbus TCP/IP protocol to control ISaGRAF controllers with VB? ..2
B. 10-ch Thermocouple Input Module .......................................................................3
B.1 I-7018Z .........................................................................................................3
B.2 I-87018Z .......................................................................................................3
C. μPAC-5x07P is μPAC-5x07 with PoE.......................................................................4
D. XW-107 (I/O Expansion Board) ..............................................................................5

4Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
Reference Guide
ISaGRAF User’s Manual (English Manual):
CD-ROM: \napdos\isagraf\8000\english_manu\ "user_manual_i_8xx7.pdf" &
"user_manual_i_8xx7_appendix.pdf" or
http://www.icpdas.com/products/PAC/i-8000/getting_started_manual.htm
ISaGRAF 進階使用手冊 (Chinese Manual):
CD-ROM: \napdos\isagraf\8000\chinese_manu\ "chinese_user_manual_i_8xx7.pdf" &
"chinese_user_manual_i_8xx7_appendix.pdf" or
http://www.icpdas.com/products/PAC/i-8000/getting_started_manual.htm
Hardware Manual:
PAC-5x07(P): CD\NAPDOS\uPAC-5000\document\ or
ftp://ftp.icpdas.com.tw/pub/cd/8000cd/napdos/upac-5000/document/
ISaGRAF Resource on the Internet:
Newly updated ISaGRAF IO libraries, drivers, demo, and manuals can be found at
http://www.icpdas.com/products/PAC/i-8000/isagraf.htm
Industrial Ethernet Switch: NS-205 / NS-208 / NS-205PSE
Best choice for Industrial Ethernet Communication.
http://www.icpdas.com/products/Switch/switch_list.htm
Note: The NS-205PSE is a POE version for PAC-5007P/5107P PAC.
FAQ:
Please refer to our website www.icpdas.com > FAQ > Software > ISaGRAF for Frequently
Asked Question, or click directly on web http://www.icpdas.com/faq/isagraf.htm

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .5
Performance Comparison Table of ISaGRAF PACs
Please click on the link ISaGRAF Comparison Table or follow the below steps:
1. www.icpdas.com
2. Click here to go to the ISaGRAF
page
3. Comparison Table

6Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
Specifications: μPAC-5x07(D)/5x07P(D)
Model
μPAC-5007(D)
μPAC-5007P(D)
μPAC-5107(D)
μPAC-5107P(D)
μPAC-5207(D)
μPAC-5307(D)
System Software
OS
MiniOS7 (DOS-like embedded operating system)
Development Software
ISaGRAF Version 3
IEC 61131-3 standard. Languages: LD, ST, FBD, SFC, IL & FC
Max. Code Size
Accepts max. 64 KB ISaGRAF code size (Appli.x8m must < 64 KB)
Power Supply
Protection
Power reverse polarity protection
Frame Ground
Yes (for ESD Protection)
Redundant Power
Inputs
Yes
Input Range
+12 ~ +48 VDC
PoE
IEEE 802.3af, Class 1
-
Power Consumption
2 W ; μPAC-5x07D/5x07PD: 2.5 W
General
Temperature
Operating: -25°C ~ +75°C, Storage : -30°C ~ +80°C
Humidity
10 % ~ 90 % RH (non-condensing).
System
CPU
80186 (80 MHz, 16 bit) or compatible.
SRAM
768 KB
Battery Backup SRAM
512 KB (Data valid up to 5 years, max. 1024 retain variables).
FLASH
512 KB (100,000 erase/write cycles).
microSD Expansion
Yes (ISaGRAF doesn’t support).
NVRAM
31 bytes (Battery backup, data valid up to 10 years).
EEPROM
16 KB (Retention > 100 years;1,000,000 erase/write cycles).
7-Seg. LED Display
5-Digit 7-Seg. LED on the front of μPAC-5x07(D)/5x07P(D). It can display
message and value.
RTC (Real Time Clock)
Provide second, minute, hour, date, day of week, month, year.
Watchdog Timers
Yes (Default: 0.8 s).
NET ID
User-assigned by software, 1 ~ 255.
Hardware Serial
Number
Yes, 64-bit hardware unique serial number.

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .7
Communication Interface
COM1
RS-232: TxD, RxD, RTS, CTS, GND, Non-Isolated.
Baudrate: Max. 115200 bps, Program downloads port.
COM2
RS-485: D2+, D2-, Non-Isolated, self-tuner ASIC inside.
Baudrate: Max. 115200 bps.
Ethernet
RJ-45 x 1, 10/100 Base-TX, Program downloads port.
(Auto-negotiating, Auto MDI/MDI-X, LED indicator)
LED Indicator
Programmable LED
2 (for User-Defined)
Hardware Expansion
I/O Expansion Bus
Yes (for one XW-board).
Dimensions
W x H x D
91 mm x 123 mm x 52 mm
PWM Output
Pulse Width
Modulation Output
All XW-Board series DO boards support PWM output. Max. 8 channels for
one controller. 500 Hz max. for Off=1 & On=1 ms
Output square curve: Off: 1 ~ 32767 ms, On: 1 ~ 32767 ms
Counters
Parallel DI Counter
All XW-Board series DI boards support DI counter. Max. 8 channels for one
controller.
Counter value: 32 bit; 500 Hz max. Min. ON & OFF width must > 1 ms
Remote DI Counter
All remote I-7000 & I-87K DI modules support counters. 100 Hz max.
value: 0 ~ 65535
Remote High Speed
Counter
Optional I-87082: 100 kHz max. , 32 bit
Protocols
Modbus RTU/ASCII
Master Protocol
Up to 2 COM Ports (COM1, COM2 and COM3-in-XW-Board) support
Modbus RTU/ASCII Master protocol to connect to other Modbus Slave I/O
devices. Max. Mbus_xxx Function Block amount: 128.
Modbus RTU Slave
Protocol
Up to 2 COM Ports (COM1 and one of COM2/COM3-in-XW-Board) can
support Modbus RTU Slave protocol for connecting ISaGRAF, PC/HMI/OPC
Server & MMI panels.
Modbus TCP/IP Slave
Protocol
Ethernet port supports Modbus TCP/IP Slave protocol for connecting
ISaGRAF & PC/HMI. Max. 6 connections.
Remote I/O
One of COM2 or (COM3:RS-485 in-XW-Board) supports I-7K, I-87K I/O
modules as Remote I/O. I-87K series must plug on RU-87P(High profile) or
I-87K(Low profile) I/O Unit. Max. 64 I/O modules for one PAC.
Fbus
Built-in COM2 Port to exchange data between ICP DAS’s ISaGRAF PACs.

8Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
Ebus
To exchange data between ICP DAS’s ISaGRAF Ethernet PACs via Ethernet
port.
Send E-mail
Actively or passively sending E-mail via Ethernet port through internet.
Max.10 receivers for each sending and can send E-mail with an attached
file. (Max. file size is about 488 KB)
SMS: Short Message
Service
One of (COM1 or COM3: RS-232 in-XW-Board) can link to a GSM modem
to support SMS. User can request data/control the controller by cellular
phone. The controller can also send data & alarms to user's cellular phone.
Optional GSM modem: GTM-201-RS232 (GSM/GPRS 850/900/1800/1900)
Note: μPAC-5207, 5307 has built-in GPRS, no external GSM/GPRS modem
required.
User-defined Protocol
User can write his own protocol applied at COM1, COM2 & (COM3 ~
COM8 -in-XW-Board) by serial communication function blocks.
MMICON/LCD
One of (COM3: RS-232 in-XW-Board) supports ICP DAS's MMICON. The
MMICON is featured with a 240 x 64 dot LCD and a 4 x 4 Keyboard. User
can use it to display picture, string, integer, float, and input a character,
string, integer and float.
Redundant Solution
Two PACs plug with XW107 in slot0. One is Master, one is Slave. Master
handles all inputs & outputs at run time. If Master is damaged (or power
off), Slave will take over the control of Bus7000b. If Master is alive from
damaged (or power up again), it takes the control of Bus7000b again. The
change over time is about 5 seconds. Control data is exchanging via Ebus
(if using a cross cable, no require any Ethernet Switch). All I/O should be
RS-485 I/O except the status I/O in the slot 0: XW107.
CAN/CANopen
Use COM1 or COM3 ~ COM8 (at the XW5xx RS-232 X-board) to connect
one I-7530: the RS-232 to CAN converter to support CAN/CANopen devices
and sensors. One PAC supports max. 3RS-232 ports to connect max. 3
I-7530 modules. Please refer to:
www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 086

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .1-1
Chapter 1. Typical Application
1.1 μPAC-5007 (P)/5107 (P)/5207/5307 Comparison Table
Model
CPU
Flash
SRAM
Memory
Expansion
Ethernet
POE
GPS
GPRS
RS-232/RS-485
μPAC-5007
μPAC-5007P
80186
80M
512
KB
768
KB
512 KB
Battery-backup
SRAM
10/100
Base TX
-
Yes
-
-
1/1
μPAC-5107
μPAC-5107P
-
Yes
Yes
-
μPAC-5207
-
-
Yes
μPAC-5307
-
Yes
Yes
All of the following applications are applicable to μPAC-5x07(P)(D) PAC. The μPAC-5007D is
used in following diagram.
1.2 Local & Remote I/O Application
Advantage of using RU-87P4/P8 + I-87K I/O modules:
Hot-Swap
Auto-Configuration at Run Time
Plug & Play at Run Time
NOTE: RU-87Pn support only High profile I-87K I/O module.
There are several X-Boards to
expand more I/O channels, COM
Ports, SRAM memory, etc.
Nearly 100 choices of Remote I/O
modules: I-7000 & I-87K.

1-2 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
1.3 Multi-HMI Application
1.4 Active Data Acquisition & Auto-Report System
μPAC-5x07(P) can use UDP/IP Client protocol to auto-report acquisition data & control data to
local or to remote internet PC/Server.
Advantage: Each PAC in the different location doesn't require a fixed Internet IP.
Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 065

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .1-3
1.5 Data Logger
ICP DAS provides a freeware “UDLoader.exe”to load the data stored in battery-backup SRAM
via RS-232 or Ethernet port.
1.6 Modbus Converter of Remote I/O Modules
μPAC-5x07(P) can be a Modbus RTU Serial and TCP/IP converter of I-7000 & I-87K series I/O
modules.

1-4 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
1.7 Data Exchange through Ethernet or RS-485
Each μPAC-5x07(P) can send or receive data to each other via the Ebus (Ethernet) or Fbus
(RS-485) communication mechanism on the same network.
1.8 Send Email with an Attached File
μPAC-5x07(P) can send Email with one attached file via Ethernet Port. The maximum file size is
about 488K bytes and one Email can send to 10 receivers at one sending.

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .1-5
1.9 SMS: Short Message Service
Short message can be sent in multiple language format (such as Chinese, English... others)
Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 111
μPAC-5207/5307 has built-in GPRS, no external GSM/GPRS modem required.
1.10 Integrate with CAN/CANopen Devices and Sensors
μPAC-5x07(P) supports max. 3I-7530 (RS-232 to CAN) converters.
Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 86

1-6 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
1.11 Connecting other Device via Modbus Master
μPAC-5x07(P) supports up to 2 COM ports of Modbus RTU/ASCII Master protocol to integrate
with other Modbus devices.
RS-485:
RS-232:
Note: COM3 ~ COM8 is optional from XW-Board XW5xx I/O expansion board.
μPAC-5x07(P) can plug one I/O Expansion board inside the main box. To install it, user
has to loosen the screw, remove the shell of μPAC-5x07(P) and then plug in the
XW-board. Please refer to below web for new products:
http://www.icpdas.com/products/PAC/up-5000/XW-board_Selection_Guide.htm.

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .1-7
1.12 GPS Applications: ISaGRAF PAC plus I-87211W or GPS-721
μPAC-5007(P)/5207 can support one I-87211W via COM1 (RS-232) or I-87211W/GPS-721 as
RS-485 remote GPS I/O.
For doing auto-time-synchronization and getting local longitude and latitude.
Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 107
GPS Receiver: www.icpdas.com > Products > Wireless... > GPS receiver
Note: μPAC-5107(P), μPAC-5307 has built-in GPS function.

1-8 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
1.13 ZigBee Wireless Solution
ISaGRAF PAC plus ZB-2550P and ZB-2551P (ZigBee to RS-232/485 Converters) can apply
wireless communication, reduce the wiring cost, and achieve the mission of remote I/O control
and data acquisition.
Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English) - 110

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .2-1
Chapter 2. Software Programming
2.1 Step 1 –Installing ISaGRAF Software
There are two kinds of software to be installed in PC before user can program on the
PAC-5x07(P) PAC system. They are:
A. ISaGRAF Workbench and
B. ICP DAS Utilities for ISaGRAF
User has to purchase at least one pcs. of ISaGRAF workbench Version 3 (ISaGRAF-256) to
install on his PC to edit, download, monitor & debug the controller system. Item (B) is
free and it is burned inside the CD-ROM which is delivered with the PAC-5x07(P).
Operating System Requirements:
Before you install the “ISaGRAF Workbench”software, you must install one of the
following operating system:
Windows 95 / Windows 98 / Windows 2000
Windows NT Version 3.51 or Windows NT Version 4.0
Windows XP, Vista or Windows 7
(Please refer to www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (Chinese) - 117)
Steps to Install the ISaGRAF Workbench:
1. Insert the ISaGRAF Workbench CD into your CD-ROM drive.
If your computer does not auto-start the installation, use the Windows Explorer and
go to the CD-ROM drive where the Workbench CD is installed.
2. Double-click on the "install.bat" file listed on the ISaGRAF CD.
If the "install.bat" file is not found on your ISaGRAF CD, then double-click on the
"ISaGRAF.exe" file to start the installation process.
Select the language.
Recommend to use “English”because
this manual uses English version.

2-2 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
3. Click on the windows [Start] > [All Programs] > [ISaGRAF 3.x] > [Projects] to start the
ISaGRAF software.
Note1: You must install the hardware protection device (dongle) provided with the ISaGRAF
software on your computer parallel port for ISaGRAF program to achieve fully
authorized functionality.
While using ISaGRAF and the dongle is plugged, if the menu [Help] > [About] says
“Maximum number of IO variables: 32”, it means ISaGRAF workbench cannot find the
dongle. Please reset your PC and then verify the [Help] > [About] again.
Note2: If it still displays “Maximum number of IO variables: 32”, the dongle driver may not be
installed well. Please execute the ISaGRAF CD_ROM \Sentinel5382\setup.exe for
ISaGRAF-80, while \Sentinel\setup.exe for other ISaGRAF version and then reset the PC
again.
Note3: Since ISaGRAF 3.51, it is using USB protection-key. To make your PC recognize the
ISaGRAF USB protection-key, please un-plug the USB key from your USB port first, then
run “\Sentinel\SSD5411-32bit.exe”in the ISaGRAF 3.51 ~ 3.55 CD-ROM after you have
installed the ISaGRAF. Then you have to plug on the USB protection-key before you
executing ISaGRAF Projects every time.
Important Notice for Windows 2000 Users:
If you close some ISaGRAF windows, it holds about 20 ~ 40 seconds (No response). This
may caused by the procedure “CTFMON.EXE” of Windows 2000. To avoid this problem,
you may create a short cut for the “ISaGRAF project manager”. And then verify the "run
in separate memory space" option in the shortcut property.
1.
2.

Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS .2-3
Important Notice for Windows NT Users:
If your computer is using the “Windows NT”OS, you will need to add one line to the file
in the ISaGRAF Workbench folder. C:\isawin\exe\isa.ini
You can use any ASCII based text editor to open the "isa.ini" file. Locate the [WS001]
header in the file (it should be at the top of the file). Anywhere within the [WS001]
header portion of the file, add the entry shown below.
[WS001]
NT=1
Isa=C:\ISAWIN
IsaExe=C:\ISAWIN\EXE
Group=Samples
IsaApl=C:\isawin\smp
IsaTmp=C:\ISAWIN\TMP
Important setting for using variable arrays:
Please add two more lines on the top of the c:\isawin\exe\isa.ini file to enable the usage
of variable arrays.
[DEBUG]
Arrays=1

2-4 Getting Started: PAC-5007(P)/5107(P)/5207/5307 Ver. 1.0, 07/2010 ICP DAS
2.2 Step 2 –Installing ICP DAS Utilities for ISaGRAF
“ICP DAS Utilities for ISaGRAF” consists of 3 major functions:
I/O libraries (for PAC-5x07(P) and other ISaGRAF PAC)
Modem_Link utility
Auto-scan I/O utility
Note: Make sure you have installed the ISaGRAF Workbench program, IF NOT, please refer to
Ch 2.1 Step 1 before continuing.
There is a CD-ROM supplied with each of the PAC-5x07(P) PAC with the “ICP DAS
Utilities for ISaGRAF”. Please insert the CD-ROM into your CD-ROM drive. Then run
CD-ROM: \napdos\isagraf\setup.exe. Follow the steps to install it.
If “ICP DAS Utilities for ISaGRAF” is not in your CD-ROM, please refer to website of
http://www.icpdas.com/products/PAC/i-8000/isagraf-link.htm , then find “ICP DAS Utilities
for ISaGRAF” to download “io_lib.zip”.