ICP DAS USA WISE-75 M Series User manual

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
1
Quick Start Guide for
WISE-7xxx Series Module
December 2016, Version 1.3
Thank you for purchasing WISE-7xxx –one of the most cost-effective automation
solutions for remote monitoring and control applications. This Quick Start Guide will
provide you with minimum information to get started with WISE-7xxx. It is intended for
use only as a quick reference. For more detailed information and procedures, please
refer to the full user manual on the CD included in this package.
In addition to this guide, the package includes the following items:
WISE-71xx / WISE-790x
Series Module
WISE-72xx
Series Module
WISE-75xxM
Series Module
Software Utility
CD
WISE-71xx / WISE-72xx User Manual
CD : \WISE-71xx\document\User Manual\
ftp://ftp.icpdas.com/pub/cd/wise_cd/wise-71xx/document/user manual/
WISE-75xxM User Manual
CD : \WISE-75xxM\document\User Manual\
ftp://ftp.icpdas.com/pub/cd/wise_cd/wise-75xxM/document/user manual/
WISE-790x User Manual
CD : \WISE-790x\document\User Manual\
ftp://ftp.icpdas.com/pub/cd/wise_cd/wise-790x/document/user manual/
WISE Website
http://wise.icpdas.com/
ICP DAS Website
http://www.icpdas.com/

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
2
Make sure the switch is in the
“Normal” position. (except WISE-75xxM)
2
----------------------------------------------------------------------------------
Connect to Network, PC and Power
Connect to Ethernet hub/switch and PC via the RJ-45 Ethernet port.
1
--------------------------------------------
Configure Boot Mode
Non-PoE
+
GND
+Vs
PoE
+
WISE-72xx / WISE-75xxM
support POE only on E1
port.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
3
3
---------------------------------------------------------------------------------
Install MiniOS7 Utility
Step 1: Get the MiniOS7 Utility tool
The MiniSO7 Utility can be obtained from companion CD or our FTP site:
CD: \Tools\MiniOS7_Utility\
ftp://ftp.icpdas.com/pub/cd/wise_cd/tools/minios7 utility/
Step 2: Follow the prompts to complete the installation
After the installation has been completed,
a new short-cut for MiniOS7 Utility will
appear on the desktop.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
4
4
----------------------------------------------------------------------------------
Assign a New IP by MiniOS7 Utility
WISE-7xxx comes with a default IP address; please assign a new IP address to the
WISE module. The factory default IP settings are as follows:
Item
Default
IPAddress
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
Step 1: Run MiniOS7 Utility
Double-click the MiniOS7 Utility
shortcut on your desktop.
Step 2: Press “F12” or click “Search” from the “Connection” menu
Press “F12”or click “Search”from the Connection menu, a MiniOS7 Scan dialog will
appear and will display all the MiniOS7 modules that are currently connected to your
network.
The “Search done”message will
appear on status bar when
searching process is finished.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
5
Step 3: Select the module name and then click “IP setting” from the toolbar
Select the module name from the list of the fields, and then click “IP setting”from the
toolbar.
Step 4: Assign a new IP address and then click “Set” button
Step 5: Click “Yes” button
After completing the settings, click the “Yes”
button to save and exit the procedure.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
6
5
----------------------------------------------------------------------------------
Go to WISE-7xxx Web Site to edit control logic.
Please follow the steps below to implement IF-THEN-ELSE control logic on controllers:
Step 1: Open a browser
Open a browser (recommended internet browsers: Mozilla Firefox or Internet Explorer).
Step 2: Type in the URL address of the WISE-7xxx
Make sure the IP address assigned is accurate (please refer to section 4: “Assign a
New IP by MiniOS7 Utility). Type in the URL address of the WISE-7xxx module in the
address bar.
Step 3: Get on the WISE-7xxx web site
Get on the WISE-7xxx web site.
Implement the control logic
configuration in the order as
indicated in the diagram.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
7
Step 4: Edit Basic Settings
Modify the Alias of the WISE module, Ethernet setting of the WISE module, the analog
input/output range, or the downloading password in the Basic Setting page as needed.
Step 5: Edit Advanced Settings
Edit channel attribute, internal register, Timer, Email, CGI commands, Recipe, and P2P
configuration settings in the Advanced Setting page as needed.

Quick Start Guide for WISE-7xxx Series Module Version 1.3
WISE-7xxx Quick Start Guide
8
Step 6: Edit Rule Settings
Edit your IF-THEN-ELSE rules in the Rules Setting page.
Step 7: Download to Module
After finishing rules setting, download the rules to the WISE module. The WISE module
will reboot and execute the rules automatically.
Step 8: For more detail information, please refer to WISE User Manual