IEI Technology uIBX-200-VX800 User manual

uIBX-200-VX800 Embedded System
Page i
Standard SIB
User Manual
MODEL:
uIBX-200-VX800
Ultra Compact Embedded System with CompactFlash
®
Slot
VGA, Gigabit Ethernet, 4 x USB, 802.11b/g Wireless,
Line out, Mic, 2 x RS-232, RoHS Compliant
Rev. 1.01 – 2009

uIBX-200-VX800 Embedded System
Page ii
Revision
Date Version Changes
4 December, 2009 1.01 Added BIOS chapter
27 August, 2009 1.00 Initial release

uIBX-200-VX800 Embedded System
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

uIBX-200-VX800 Embedded System
Page iv
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 BENEFITS ................................................................................................................... 2
1.3 FEATURES................................................................................................................... 3
1.4 TECHNICAL SPECIFICATIONS ...................................................................................... 3
1.5 CERTIFICATIONS......................................................................................................... 4
2 DETAILED SPECIFICATIONS .................................................................................. 5
2.1 FRONT PANEL............................................................................................................. 6
2.2 REAR CONNECTOR PANEL.......................................................................................... 6
2.3 DIMENSIONS............................................................................................................... 8
2.4 MAINTENANCE........................................................................................................... 8
3 UNPACKING................................................................................................................. 9
3.1ANTI-STATIC PRECAUTIONS...................................................................................... 10
3.2 UNPACKING PRECAUTIONS....................................................................................... 10
3.3 UNPACKING CHECKLIST ............................................................................................11
3.4 OPTIONAL ITEMS...................................................................................................... 12
4 INSTALLATION ......................................................................................................... 13
4.1 INSTALLATION PRECAUTIONS................................................................................... 14
4.2 JUMPER SETTINGS .................................................................................................... 15
4.2.1 AT/ATX Power Select Jumper Settings ............................................................ 15
4.2.2 CompactFlash® Master/Slave Selection......................................................... 16
4.2.3 Clear CMOS Jumper........................................................................................ 16
4.3 COMPACTFLASH®CARD INSTALLATION.................................................................. 16
4.4 EXTERNAL PERIPHERAL INTERFACE CONNECTORS................................................... 17
4.4.1 Power Input...................................................................................................... 18
4.4.2 Audio Connector .............................................................................................. 19
4.4.3 LAN Connectors............................................................................................... 19
4.4.4 Serial Port Connector...................................................................................... 21

uIBX-200-VX800 Embedded System
Page v
4.4.5 USB Connector ................................................................................................ 22
4.4.6 VGA Connector................................................................................................ 23
4.5 MOUNTING THE SYSTEM .......................................................................................... 24
4.6 SOFTWARE................................................................................................................ 26
5 BIOS.............................................................................................................................. 28
5.1 INTRODUCTION......................................................................................................... 29
5.1.1 Starting Setup................................................................................................... 29
5.1.2 Using Setup...................................................................................................... 29
5.1.3 Getting Help..................................................................................................... 30
5.1.4 Unable to Reboot After Configuration Changes.............................................. 30
5.1.5 BIOS Menu Bar................................................................................................ 30
5.2 MAIN........................................................................................................................ 31
5.3ADVANCED............................................................................................................... 32
5.3.1 CPU Configuration.......................................................................................... 33
5.3.2 IDE Configuration........................................................................................... 34
5.3.2.1 SATA Channel........................................................................................... 35
5.3.3 Super IO Configuration ................................................................................... 39
5.3.4 Power Configuration........................................................................................ 40
5.3.4.1 ACPI Configuration .................................................................................. 41
5.3.4.2 APM Configuration................................................................................... 42
5.3.5 Remote Access Configuration.......................................................................... 43
5.3.6 USB Configuration........................................................................................... 46
5.3.6.1 USB Mass Storage Device Configuration................................................. 48
5.4 PCI/PNP................................................................................................................... 49
5.5 BOOT........................................................................................................................ 52
5.5.1 Boot Settings Configuration............................................................................. 52
5.5.2 Boot Device Priority........................................................................................ 54
5.5.3 Hard Disk Drives ............................................................................................. 55
5.5.4 Removable Drives............................................................................................ 55
5.5.5 CD/DVD Drives............................................................................................... 56
5.6 SECURITY................................................................................................................. 57
5.7 CHIPSET ................................................................................................................... 57
5.7.1 Northbridge VIA® VX800 Configuration........................................................ 58
5.7.2 Southbridge VIA® VX800 Configuration ........................................................ 59

uIBX-200-VX800 Embedded System
Page vi
5.8 EXIT......................................................................................................................... 60
A SAFETY PRECAUTIONS......................................................................................... 62
A.1 SAFETY PRECAUTIONS ............................................................................................ 63
A.1.1 General Safety Precautions............................................................................. 63
A.1.2 Anti-static Precautions .................................................................................... 64
A.2 MAINTENANCE AND CLEANING PRECAUTIONS........................................................ 64
A.2.1 Maintenance and Cleaning.............................................................................. 64
A.2.2 Cleaning Tools................................................................................................. 65
B HAZARDOUS MATERIALS DISCLOSURE ......................................................... 66
B.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY....................................... 67

uIBX-200-VX800 Embedded System
Page vii
List of Figures
Figure 1-1: uIBX-200-VX800...........................................................................................................2
Figure 2-1: Front Panel ..................................................................................................................6
Figure 2-2: uIBX-200-VX800 Peripheral Connectors...................................................................7
Figure 2-3: Physical Dimensions (millimeters)............................................................................8
Figure 4-1: CompactFlash® Card Installation ...........................................................................17
Figure 4-2: Peripheral Connectors (Rear)..................................................................................18
Figure 4–3: Peripheral Connectors (Front)................................................................................18
Figure 4-4: Power Terminal Block...............................................................................................19
Figure 4-5: Audio Connector.......................................................................................................19
Figure 4-6: LAN Connection........................................................................................................20
Figure 4-7: RJ-45 Ethernet Connector........................................................................................20
Figure 4-8: Serial Device Connector................................................Error! Bookmark not defined.
Figure 4-9: Serial Port Pinouts....................................................................................................22
Figure 4-10: USB Device Connection.............................................. Error! Bookmark not defined.
Figure 4-11: VGA Connector .......................................................................................................23
Figure 4-12: VGA Connector .......................................................................................................23
Figure 4–13: Attachment Installation..........................................................................................24
Figure 4–14: System Attachment Screws..................................................................................25
Figure 4–15: Mounting Screws....................................................................................................26

uIBX-200-VX800 Embedded System
Page viii
List of Tables
Table 1-1: Technical Specifications..............................................................................................4
Table 3-1: Package List Contents...............................................................................................11
Table 3-2: Optional Items.............................................................................................................12
Table 4-1: Jumpers.......................................................................................................................15
Table 4-2: AT/ATX Power Select Jumper Settings....................................................................15
Table 4-3: CompactFlash® Master/Slave Selection..................................................................16
Table 4-4: Clear BIOS Jumper Settings......................................................................................16
Table 4-5: LAN Pinouts ................................................................................................................20
Table 4-6: RJ-45 Ethernet Connector LEDs...............................................................................21
Table 4-7: Serial Port Pinouts......................................................................................................21
Table 4-8: USB Port Pinouts........................................................................................................22
Table 4-9: VGA Connector Pinouts.............................................................................................23
Table 5-1: BIOS Navigation Keys................................................................................................30

uIBX-200-VX800 Embedded System
Page 1
Chapter
1
1 Introduction

uIBX-200-VX800 Embedded System
Page 2
1.1 Overview
Figure 1-1: uIBX-200-VX800
The uIBX-200-VX800 embedded system is an ultra small PC for installation between a
computer screen and its stand. It is powered by the VIA® Eden™ ULV 1 GHz/500 MHz
processor, uses the VIA® VX800 system chip and has 1.0 GB or 512 MB of DDR2
memory.
The VIA® VX800 system chip provides many built-in graphics functions allowing high
quality video playback without the need for expensive hardware.
The uIBX-200-VX800 is best when combined with the optional CompactFlash® card with
Microsoft® Windows XP Embedded or Linux preinstalled. A software development kit and
documentation are also available to help easily customize the operating system according
to the installation requirements.
1.2 Benefits
Some of the uIBX-200-VX800 benefits include:
Customizable operating system to suit application needs.
Less downtime from overheating because there are not fans to fail
Cost savings with low power consumption
Easy installation on standard VESA mounting
Both wired and wireless network connectivity

uIBX-200-VX800 Embedded System
Page 3
1.3 Features
The uIBX-200-VX800 features are listed below:
VIA® Eden™ ULV 1 GHz/500 MHz processor
1.0 GB or 512 MB of DDR2
VGA video output
One Gigabit Ethernet port
Four USB 2.0 ports
Two RS-232 serial ports
RoHS compliant
1.4 Technical Specifications
The uIBX-200-VX800 technical specifications are listed in Table 1-1.
Specifications
System
CPU VIA® Eden™ ULV 1 GHz/500 MHz processor
Memory 1.0 GB or 512 MB of DDR2 memory
Real-time Clock Battery backup RTC
Watchdog Timer Software programmable supports 1~255 sec. system reset
Reset Reset button
Display
Video Output VGA
Video Support Integrated graphics processor with 2D / 3D / Video
controllers
2D and 3D graphics processor
Supports MPEG2, WMV9 / VC1 decoding
(Standard drivers provide the DirectX Video Acceleration
interface to enable video acceleration. User application
protocols need to use the DirectX Video Acceleration
interface to enable the acceleration features)

uIBX-200-VX800 Embedded System
Page 4
Specifications
I/O and Communications
Ethernet 1 x 10/100/1000 Mb/s
1 x 802.11b/g (optional)
Serial Ports 2 x RS-232
USB Interfaces 4 x USB 2.0 host connectors
Audio Line out
Microphone in
Power
Power Supply 5 VDC
Power Consumption 15 W
Environmental and Mechanical
Operating Temperature 0ºC~50ºC
Humidity 5%RH to 90%RH (non-condensing)
Vibration Operating Random Vibration Mode (MIL-STD-810F
514.5C-3)
1.Axes: 3 axs (Vertical / Transverse / Longitudinal).
2.10-500 Hz, 60min/axis.
3.Equivalent to Z:2.18 Grms X:1.6 Grms Y:1.96 Grms
Color Black front, sides and bottom.
Light gray top and back
Physical Dimensions 120 mm x 44.4 mm x 125 mm
Table 1-1: Technical Specifications
1.5 Certifications
All uIBX-200-VX800 series models comply with the following international standards:
RoHS
CE, FCC Class A, CCC
For a more detailed description of these standards, please refer to Appendix A.

uIBX-200-VX800 Embedded System
Page 5
Chapter
2
2 Detailed Specifications

uIBX-200-VX800 Embedded System
Page 6
2.1 Front Panel
The front panel consists of a small door, giving access to the CompactFlash® card, and
also has two USB ports, an audio output and microphone input jack.
Figure 2-1: Front Panel
Connectors and buttons on the front panel include the following.
1 x CompactFlash® slot
2 x USB connectors
1 x Microphone input
1 x Line output
2.2 Rear Connector Panel
All external peripheral interface connectors are located on the bottom panel of the
uIBX-200-VX800 . The peripheral interface connectors are shown in Figure 2-2.

uIBX-200-VX800 Embedded System
Page 7
Figure 2-2: uIBX-200-VX800 Peripheral Connectors
Connectors and buttons on the rear panel include the following.
1 x 5 V DC power input
1 x Power switch
1 x VGA output
2 x RS-232 ports
2 x USB ports
1 x Gigabit Ethernet port
1 x Antenna connector (certain models only)

uIBX-200-VX800 Embedded System
Page 8
2.3 Dimensions
The physical dimensions are shown and listed below:
Width: 120 mm
Height: 44.4 mm
Depth: 125 mm
Figure 2-3: Physical Dimensions (millimeters)
2.4 Maintenance
Don't open the uIBX-200-VX800 (except the CompactFlash® door), there are no
user-serviceable parts inside.

uIBX-200-VX800 Embedded System
Page 9
Chapter
3
3 Unpacking

uIBX-200-VX800 Embedded System
Page 10
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during installation may result in
permanent damage to the uIBX-200-VX800 and severe injury to the
user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the uIBX-200-VX800. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the uIBX-200-VX800 or any other electrical component is
handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the uIBX-200-VX800, place it on
an antic-static pad. This reduces the possibility of ESD damaging the
uIBX-200-VX800.
3.2 Unpacking Precautions
When the uIBX-200-VX800 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 3.1.
Make sure the packing box is facing upwards so the uIBX-200-VX800 does
not fall out of the box.
Make sure all the components shown in Section 3.3 are present.

uIBX-200-VX800 Embedded System
Page 11
3.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact your sales
representative directly. To contact us http://www.emacinc.com/support/
The uIBX-200-VX800 is shipped with the following components:
Quantity Item and Part Number Image
1 uIBX-200-VX800
1 Power adapter
1 Screw set
1 Quick installation guide
1 Driver CD
Table 3-1: Package List Contents

uIBX-200-VX800 Embedded System
Page 12
3.4 Optional Items
Quantity Item Image
uIBXVK-200B Double side VESA mount kit for
uIBX-200, black
Table 3-2: Optional Items