IEI Technology KINO-DAL User manual

1
Mini-ITX SBC supports Intel® 14nm Atom™, Pentium® or Celeron®
on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB 3.0,
PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
KINO-DAL
Quick Installation Guide
Version 1.0
May 04, 2018.
Package List
KINO-DAL package includes the following items:
1 x KINO-DAL single board computer with Heatsink
1 x SATA with power cable kit (P/N: 32801-000201-100-RS )
1 x I/O Shielding
1 x QIG (Quick Installation Guide)
©2018 Copyright by IEI Integration corp.
All rights reserved.

2
Specifications
SoC:
Intel® Atom® x7-E3950 on-board SoC (2.0GHz, quad-core)
Intel® Atom® x5-E3940 on-board SoC (1.8GHz, quad-core)
Intel® Atom® x5-E3930 on-board SoC (1.8GHz, dual-core)
Intel® Pentium® N4200 on-board SoC (2.5GHz, quad-core)
Intel® Celeron® N3350 on-board SoC (2.3GHz, dual-core)
BIOS:AMI UEFI BIOS
Memory:
Two 204-pin 1866/1600MHz Dual-channel DDR3L DIMMs
support up to 8GB
Graphics Engine:
Intel® HD Graphics Gen9 Low Power; 18 Execution Units
4K Codec Decode & Encode for HEVC 4 , H.264, VP8, SVC,
MVC
Display Output:
Triple Independent Displays
1 x LVDS: 18/24-bit dual-channel LVDS by CH7511B DP to
LVDS converter (up to 1920x1200@60Hz)
1 x VGA: by CH7517 DP to VGA converter(up to
1920x1200@60Hz)
1 x HDMI (up to 3840x2160 @ 30Hz)
Ethernet:
2 x PCIe GbE LAN Intel i211 AT /i210 AT/ i210 IT Controller
Super I/O:Fintek F81866
Embedded Controller:iWDD IT8528E
External I/O Interface:
4 x USB 3.0
2 x RS-232/422/485
Internal I/O Interface:
2 x SATA 6G/s with 12/5V SATA power connector (No RAID)
4 x USB 2.0 (2x4 pin, P=2.00)

3
1 x USB 2.0 (180° Type-A)
4 x RS-232 (2x5 pin, P=2.00)
1 x KB/MS (1x6 pin)
SMBus: 1 x SMBus (1x4 pin)
I2C: 1 x I2C (1x4 pin)
TPM: 1 x TPM (2x10 pin)
Audio:
Realtek ALC662 HD codec
2 x Audio Jacks (Co-lay 3 Jacks type) (Mic-in, Line-out)
1 x Analog audio (2x5 pin)
Front Panel:
1 x Front Panel (2 x 7 pin)
LAN LED: 2 x LAN LED (1x2 pin)
Expansion :
1 x PCIe x1
1 x Full/Half-size PCIe Mini slot (1 w/ SIM holder (Optional))
1 x M.2 (B Key) (2242)(SATA port1 + USB 2.0 signal)
1 x Micro SD(Optional)
eMMC: 8GB eMMC 5.0 suppport (optional)
Digital I/O: 1 x 8-bit digital I/O (2x5 pin)
Fan Connector:
1 x CPU fan connector (1x4 pin)
1 x System fan connector (1x3 pin)
Power supply:
12V only DC input as Default/ 9V~30V DC input (Optional)
1 x Internal power connector (2x2 pin)
1 x External DC power Jackc (Ø5.5mm)
Support AT/ATX mode
Watchdog Timer:
Software programmable supports 1~255 sec. system reset
Operating Temperature: -20°C ~ 60°C / -40°C ~ 85°C

4
Storage Temperature: -40°C ~ 85°C
Operation Humidity: 5% ~ 95%, non-condensing
Dimension: 170mm x 170mm
Weight:GW:1100g / NW:700g
Ordering Information

Mini-ITX SBC supports Intel® 14nm quad-core Pentium® N4200
2.5GHz on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB
3.0, PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
KINO-DAL-N2-R10:

Mini-ITX SBC supports Intel® 14nm dual-core Celeron® N3350
2.3GHz on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB
3.0, PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
KINO-DAL-N1-R10:

Mini-ITX SBC supports Intel® 14nm quad-core Atom® x7-E3950
2.0GHz on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB
3.0, PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS, -40°C ~
85°C
KINO-DAL-E3W2-R10:
KINO-DAL-E2W2-R10:
All the drivers and One Key Recovery
utility for the KINO-DAL are available on
IEI Resource Download Center. Type
KINO-DAL and press Enter to find all the
relevant software, utilities, and
documentation. To install software from
the downloaded ISO file, mount the file
as a virtual drive to view its content.
IEI Resource Download Center
https://download.ieiworld.com

5
Mini-ITX SBC supports Intel® 14nm quad-core Atom® x5-E3940
1.8GHz on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB
3.0, PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS, -40°C ~
85°C

Mini-ITX SBC supports Intel® 14nm dual-core Atom® x5-E3930
2.0GHz on-board SoC with HDMI/LVDS/VGA, Dual PCIe GbE, USB
3.0, PCIe Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS, -40°C ~
85°C
KINO-DAL-E1W2-R10:
32000-070301-RS:

Dual-port USB cable, 210mm, P=2.0
32000-023800-RS:

PS/2 KB/MS cable, 135mm, P=2.0
32205-002700-100-RS:

RS-232 cable, 200mm, P=2.0
TPM-IN01-R11:
20-pin Infineon TPM module, software management tool, firmware
V3.17
TPM-IN02-R11:
20-pin Infineon TPM2.0 module, software mangement tool, firmware
v5.5

6
Jumpers setting and connectors
LABEL FUNCTION
J_CMOS1 Clear CMOS Setup
SW_A/T1 ATX or AT Power Select
J_SATA1 M.2 SATA(M2_1) or SATA2 Select
J_PW1 LCD Power Select
F_PANEL1 F_PANEL Pin Header 2.54mm Pitch
HDA1 Front Panel Audio Connector
SW1 LCD Panel Type Select
TPM1 LPC Interface for Port 80h Debug Tool
CPU_FAN1 CPU Fan Connector
SYS_FAN1 System Fan Connector
SATA_PWR1/SATA_PWR2 SATA HDD Power Connector
J_SPI1/J_EC1 J_SPI1 Connector for System BIOS.
J_EC1 Connector for EC ROM.
COM1/2
Internal RS-232/RS-422/RS-485 Serial
Port Connectors
COM3-6 Internal RS-232 Serial Port Connectors
KB/MS1 PS2 Keyboard & Mouse Connector
J_SMB1/JI2C1 SMBus / I2C Connector
LVDS1 LVDS Connector for LVDS LCD Panel
INV11 LCD Inverter Connector
PWR1/PWR2 DC 12V System Power Input Connector
J_KB/MS1 PS2 Keyboard and Mouse Connector
USB1/USB2
Internal USB 2.0 Connectors (Pitch 2.0
mm)
DIO1 Digital I/O Connector
BT1 RTC Battery connector
JLAN_LED1/JLAN_LED2
LAN1,LAN2 Active LED Pin header
2.0mm Pitch
SBY_LED1
Yellow Green color to indicator standby
+3.3V
PWR_LED1 Blue color to indicator system +5V
PWR_SW1 Power ON/OFF Switch
DIMM1 204-pin DDR3 SO-DIMM Channel A

7
DIMM2
204-pin DDR3 SO-DIMM Channel B
SATA1/SATA2 Standard 7Pin SATA Connector
VGA1 Standard DB15 VGA Connector
HDMI1 Standard HDMI Connector
LAN1_USB01_1/LAN2_USB23_1
Standard RJ-45
and Dual USB 3.0 With
LED Connector
SD1
Standard Micro-SD Slot (Optional)
MPCIE1 Standard Mini-PCIE Slot
PCIE1 Standard PCIE *1 X Slot
SIM1 Micro-SIM Card Slot (Optional)
J_CS1
Chassis open Connector. pitch 2.0mm
pinheader
SW_A/T1: ATX or AT Power Select
PIN NO.
DESCRIPTION
Short A-B
ATX Power Mode (default)
Short B-C
AT Power Mode
J_PW1: LCD Power Select
PIN NO.
DESCRIPTION
Short 1-2
+3.3V (default)
Short 2-3
+5V
J_SATA1: M.2 SATA(M2_1) or SATA2 Select
PIN NO. DESCRIPTION
Short A-B Auto Detect M.2 or SATA2 (default)
Short B-C M.2 SATA Enable(SATA2 Disable)
J_CMOS1: Clear CMOS Setup
PIN NO.
DESCRIPTION
Non-press
Normal Operation (default)
Press
Clear CMOS Setup

8
F_PANEL1: F_PANEL Pin Header 2.54mm Pitch
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 PWR_LED+ 2 SPKR+
3 NC 4 NC
5
PWR_LED-
6
NC
7 PWR_SW+ 8 SPKR-
9 PWR_SW- 10 NC
11
HDD_LED+
12
RESET_SW+
13 HDD_LED- 14 RESET_SW-
SW1: LCD Panel Type Select
* ON=0, OFF=1
4-3-2-1
DESCRIPTION
0000
800x600 18bit
0001
1024x768 18bit
0010
1024x768 24bit
0011
1280x768 18bit
0100
1280x800 18bit
0101
1280x960 18bit
0110
1280x1024 24bit
0111
1366x768 18bit
1000
1366x768 24bit
1001
1440x960 24bit
1010
1400x1050 24bit
1011
1600x900 24bit
1100
1680x1050 24bit
1101 1600x1200 24bit
1110 1920x1080 24bit
1111 1920x1200 24bit

9
HDA1: Front Panel Audio Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 MIC2-L 2 GND
3 MIC2-R 4 Pre-Sense#
5
LINE2-R
6
MIC2-JD
7 GND 8 Key
9 LINE2-L 10 LINE2-JD
SYS_FAN1: System Fan Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
FAN_IN
2
12V
3
GND
CPU_FAN1: CPU Fan Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
12V
3
FAN_IN
4
FANCTL
TPM1: LPC Interface for Port 80h Debug Tool
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 Clock 2 GND
3
LFRAME#
4
Serial IRQ
5 LPC Reset 6 LAD2-
7 LAD3 8 LAD0
9
+3.3V
10
LPC Reset
11 LAD0 12 GND
13 SCL 14 SDA
15 SB3V 16 SERIRQ
17
GND
18
CLKRUN#
19 LPCPD# 20 LDRQ#

10
COM3-6: Internal RS-232 Serial Port Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DCD 2 DSR
3 RXD 4 RST
5 TXD 6 CTS
7 DTR 8 RI
9
GND
10
GND
COM1/2 : Internal RS-232/RS-422/RS-485 Serial Port Connectors
Mode
RS-232
RS-422
RS-485
PIN NO.
DESCRIPTION
DESCRIPTION
DESCRIPTION
1
DCD
TXD422-
TXD485-
2
RXD
TXD422+
TXD485+
3
TXD
RXD422+
4
DTR
RXD422-
5
GND
GND
GND
6
DSR
7
RTS
8
CTS
9
RI
J_SPI1/J_EC1: J_SPI1 Connector for System BIOS. J_EC1
Connector for EC ROM.
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 4 Clock
2
CS#
5
MOSI
3 MISO 6 GND
SATA_PWR1/SATA_PWR2: SATA HDD Power Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+12V
2
GND
3
GND
4
+5V

11
LVDS1: LVDS Connector for LVDS LCD Panel
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 GND
3 A_DATA0- 4 A_DATA1-
5 A_DATA0+ 6 A_DATA1+
7 GND 8 GND
9 A_DATA2- 10 Clock1-
11 A_DATA2+ 12 Clcok1+
13 GND 14 GND
15 A_DATA3- 16 A_DATA4-
17 A_DATA3+ 18 A_DATA4+
19 GND 20 GND
21 A_DATA5- 22 A_DATA6-
23 A_DATA5+ 24 A_DATA6+
25 GND 26 GND
27 Clock2- 28 A_DATA7-
29 Clcok2+ 30 A_DATA7+
31 GND 32 GND
33 LVDS Detect(GND)* 34 GND
35 LCD VCC 36 LCD VCC
37 LCD VCC 38 LCD VCC
39 LCD VCC 40 LCD VCC
*:LVDS Detect- This pin cable must connect to GND.
J_SMB1/JI2C1: SMBus / I2C Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
Clock
3
Data
4
+5V
KB/MS1: PS2 Keyboard & Mouse Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
4
KB_DATA
2
MS_DATA
5
KB_CLK
3
MS_CLK
6
GND

12
USB1 & USB2: Internal USB 2.0 Connectors (Pitch 2.0 mm)
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 +5V 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 +5V
J_KB/MS1: PS2 Keyboard and Mouse Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VCC
4
Keyboard DATA
2
Mouse DATA
5
Keyboard Clock
3
Mouse Clcok
6
GND
PWR2: DC 12V System Power Input Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 +12V 2 GND
PS:Apollo Lake-I serial M/B Support DC Input 9V to 30V
PWR1: DC 12V System Power Input Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+12V
2
GND
3
GND
PS:Apollo Lake-I serial M/B Support DC Input 9V to 30V
INV11: LCD Inverter Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
LCD Adj
2
GND
3
+12V
4
GND
5
Backlight Enable

13
LAN1/LAN2 LED:
ACT / LINK LED
SPEED LED
Status
DESCRIPTION
Status
DESCRIPTION
OFF
No Link
OFF
10 Mbps connection
YELLOW
Link
GREEN
100 Mbps connection
BLINKING
Data activity
ORANGE
1 Gbps connection
ACT/LINK SPEED
LEDLED
JLAN_LED1/JLAN_LED2: LAN1,LAN2 Active LED Pin header
2.0mm Pitch
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
LED+
2
LED-
DIO1: Digital I/O Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
3
D_OUT3
4
D_OUT2
5
D_OUT1
6
D_OUT0
7
D_IN3
8
D_IN2
9
D_IN1
10
D_IN0
BT1: RTC Battery connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1 RTC Battery+ 2 RTC Battery-

14
Board Layout: Jumper and Connector Locations
(Unit: mm)