IEI Technology NANO-945GSE User manual

1
EPIC SBC with Intel®Atom™ N270 1.6GHz, VGA/Dual LVDS,
Dual GbE, CF II, USB, SATA
NANO-945GSE
Quick Installation Guide
Version 2.0
Aug. 03, 2011
Package Contents
NANO-945GSE package includes the following items:
z1 x NANO-945GSE Single Board Computer
z1 x KB/MS cable
z2 x SATA cable
z1 x Power cable
z2 x RS-232 cable
z1 x Mini Jumper Pack
z1 x Utility CD
z1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
zCPU: On board Intel® Atom™ N270 1.6GHz/512KB L2 Cache FSB
533MHz
zSystem Chipset: Intel® 945GSE +ICH7M
zBIOS: AMI BIOS
zSystem memory: 1 x 200-pins 533/400MHz DDR2 SDRAM
SO-DIMM (max. 2GB)
zEthernet: Dual Realtek RTL8111E GbE Controllers
zI/O Interface:
2 x SATA
6 x USB 2.0 (4 by header, 2 on rear side)
1 x CF Type II
3 x RS-232
1 x RS-232/422/485
1 x PS/2 KB/MS, 1 x KB/MS by 1x6 pins wafer-header
1 x IDE
1 x LPT
zExpansions:
1 x PCI-104(PCI-BUS)
1 x PCIe mini card slot
zAudio: Support by Audio Kit (AC'97 & HD)
5.1 channel AC'97 Audio Kit with Realtek ALC655 codec
7.1 channel HD Audio Kit with Realtek ALC888 codec support dual
audio streams
zDigital I/O: 8-bit digital I/O, 4-bit input/ 4-bit output by super I/O
zIrDA: 1x Infrared Interface by super I/O
zSuper I/O: ITE IT8718F
zDisplay Interface:
Analog CRT: Support for CRT Hot plug
18/24-bit Dual-Channel LVDS by SDVO to LVDS Transmitter:
Chrontel CH7308B
18-bit Dual-Channel LVDS from Intel® 945GSE
Support HDTV resolution up to 1080i by component interface
zWatchdog timer:

3
Software programmable supports 1~255 sec. system reset
zPower Supply: +12V only, AT/ATX support
zPower Consumption:
[email protected](DDR2 667MHz 1GB) (Windows® XP, 3D mark®2001)
zHumidity: Operation: 5% ~ 95%, non-condensing
zTemperature: 0 ~ 60°C(32 ~ 140°F)
zDimension: 165 mm x 115 mm
zWeight: GW: 1100g; NW: 250g
Ordering Information
NANO-945GSE-N270-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/LVDS, Dual GbE,CFII, USB,
SATA
NANO-945GSE-N270W-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/LVDS, Dual GbE,CFII, USB,
SATA, -20~70C
NANO-945GSE-N270W2-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/LVDS, Dual GbE,CFII, USB,
SATA, -40~85C
NANO-945GSELVDS2-N270-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/Dual LVDS, Dual GbE,CFII,
USB, SATA
NANO-945GSELVDS2-N270W-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/Dual LVDS, Dual GbE,CFII,
USB, SATA, -20~70C
NANO-945GSELVDS2-N270W2-R20:
EPIC SBC with Intel® Atom™ N270 1.6G, VGA/Dual LVDS, Dual GbE,CFII,
USB, SATA, -40~85C
AC-KIT08R-R10: 5.1 channel AC'97 Audio Kit with Realtek ALC655 codec
AC-KIT-888HD-R10: 7.1 channel HD Audio Kit with Realtek ALC888 codec
support dual audio streams
32000-044300-RS:Dual port USB cable
32200-015100-RS:LPT cable
32200-026500-RS:RS-232/422/485 cable
32100-043403-RS:ATX Power Cable
32000-083701-RS: HDTV out Cable
32200-000009-RS: 44pin 2.5" IDE cable
32200-008800-RS: 44pin to 2.5"/3.5" IDE cable
32100-088600-RS: SATA Power Cable
32000-114000-RS: SATA 5V power output Cable Kit for NANO series

4
Jumpers setting
LABEL FUNCTION
J_CMOS1 CMOS state setting
JP1 COM2 Port Mode setting
J_VLVDS1 LVDS1 Voltage Selection
J_VLVDS2 LVDS2 Voltage Selection
JP2 PCI-104 VIO Selecto
r
JCF1 CF Card setting
ATXCTL1 AT Power Mode Setting
J_LCD_TYPE1 LVDS1 & LVDS2 Panel Resolution Selection

5
J_CMOS1: Clear CMOS Setup
J_CMOS1 DESCRIPTION
Short 1-2
(default)* Keep CMOS Setup (Normal Operation)
Short 2-3 Clear CMOS Setup
J_VLVDS1: LVDS1
V
oltage Selection
J_VLVDS1 DESCRIPTION
1-2 +3.3V LVDS
2-3 +5V LVDS
J_VLVDS2: LVDS 2
V
oltage Selection
J_VLVDS2 DESCRIPTION
1-2 +3.3V LVDS
2-3 +5V LVDS
JP1: configure COM2 Mode
JP1 DESCRIPTION
Short 1-2
(default) RS - 232
Short 3-4 RS - 422
Short 5-6 RS - 485
JP2: PCI-104
V
IO Voltage select
J2 DESCRIPTION
Short 1-2
V
CC (+5V)
Short 2-3
V
CC3 (+3.3V)
JCF1: Configure CF Card type
JCF1 DESCRIPTION
Open
(default) Slave
Short 1-2 Maste
r
ATXCTL1: AT Power Mode Setting
ATXCTL1 DESCRIPTION
1-2
(default) AT Power Mode
Open ATX Power Mode
J_LCD_TYPE1 : LVDS1 Panel
Resolution Selection
1-2 3-4 LVDS1
OFF OFF LVDS1 800X600
(18bit)
ON OFF LVDS1 1024 X 768
(18bit)
OFF ON LVDS1 1280X1024
(36bit)
ON ON LVDS1 1400X1050
(36bit)
J_LCD_TYPE1 : LVDS2 Panel
Resolution Selection
5-6 7-8 LVDS2
OFF OFF LVDS2 1024 X 768
(18bit)
ON OFF LVDS2 1024 X 768
(24bit)
OFF ON LVDS2 1280X1024
(36bit)
ON ON LVDS2 1280X1024
(48bit)

6
Table of Connectors
LABEL FUNCTION
VGA1 VGA 15-pin Female Connecto
r
USB_C45 2 Port USB Connecto
r
LAN1
LAN2 RJ45 LAN Connectors
KB_MS1
KB1 PS/2 MOUSE & KEYBOARD Connectors
COM1 COM Port Connecto
r
COM2 Internal Serial Port Connecto
r
s
(RS-232/422/485)
COM3
COM4 Internal Serial Port Connectors (RS-232)
LPT1 Parallel Port Connecto
r
USB01
USB23 Internal 4 Port USB Connectors
J_AUDIO1 Extend
A
udio Module Connecto
r
SATA1
SATA2 Serial ATA Connectors
IR1 Infrared Interface Connecto
r
CPU_FAN1 Fan Connecto
r
IDE1 IDE Connecto
r
TV1 TV Out Connecto
r
DIO1 Digital I/O Connecto
r
LVDS1 LVDS Panel Connecto
r
LVDS2 LVDS Panel Connecto
r
INVERTER1,2 LVDS1,2 Panel Backlight +12V Power Source
F_PANEL1 PWR & RST Buttons and
Indicators
A
TXCTL1
A
TX Power Control Connector
CN1 +12V Main Power Input Connecto
r
CN3 +5V Power Output Connector
JSPI 1 SPI flash connecto
r
BAT1 Battery connecto
r
CF1 Compact Flash Slot
PC104_PLUS1 PCI-104 Plus Connector
CN4 PCI-E Mini Card connector

7
VGA1: 15-pin Female Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 GREEN
3 BLUE 4 NC
5 GND 6 CRT_PLUG#
7 GND 8 GND
9 VCC 10 GND
11 NC 12 DDCDAT
13 HSYNC 14 VSYNC
15 DDCCLK
USB_C45: USB Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC (+5V) 5 VCC (+5V)
2 DATA4- 6 DATA5-
3 DATA4+ 7 DATA5+
4 GROUND 8 GROUND
LAN1、LAN2: RJ45 LAN Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 MDIA3- 5 MDIA1+
2 MDIA3+ 6 MDIA2+-
3 MDIA2- 7 MDIA0-
4 MDIA1- 8 MDIA0+
KB_MS1: 6-pin Mini-DIN Keyboard Connecto
r
PIN NO. DESCRIPTION
1 Keyboard Data
2 Mouse Data
3 GND
4 VCC (+5V)
5 Keyboard Clock
6 Mouse Clock
KB1: 6-pin Mini-DIN Keyboard/Mouse Connecto
r
PIN NO. DESCRIPTION
1 VCC (+5V)
2 Mouse Data
3 Mouse Clock
4 Keyboard Data
5 Keyboard Clock
6 GND

8
COM1: Serial Port Connector
PIN NO. DESCRIPTION
1 DATA CARRIER DETECT (DCD#)
2 RECEIVEDATA (RXD)
3 TRANSMITDATA (TXD)
4 DATA TERMINAL READY (DTR#)
5 GND (GND)
6 DATA SET READY (DSR#)
7 REQUEST TO SEND (RTS#)
8 CLEAR TO SEND (CTS#)
9 RING INDICATOR (RI#)
COM2 : Internal Serial Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DATA CARRIER
DETECT (DCD#) 2 DATA SET READY (DSR#)
3 RECEIVE DAT
A
(RXD) 4 REQUEST TO SEND (RTS#)
5 TRANSMIT DATA
(TXD) 6 CLEAR TO SEND (CTS#)
7 DATA TERMINAL
READY (DTR#) 8 RING INDICATOR (RI#)
9 GND 10 N/C
11 TXD485+ 12 TXD485#
13 RXD485+ 14 RXD485#
COM3 & COM4 : Internal Serial Port Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 DATA CARRIER
DETECT (DCD#) 2 DATA SET READY (DSR#)
3 RECEIVE DATA (RXD) 4 REQUEST TO SEND
(RTS#)
5 TRANSMIT DATA
(TXD) 6 CLEAR TO SEND (CTS#)
7 DATA TERMINAL
READY (DTR#) 8 RING INDICATOR (RI#)
9 GND 10 N/C

9
LPT1 : Parallel Port Connecto
r
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 STROBE# 14
A
UTO FORM FEED #
2 DATA0 15 ERROR#
3 DATA1 16 INITIALIZE#
4 DATA2 17 PRINTER SELECT LN#
5 DATA3 18 GND
6 DATA4 19 GND
7 DATA5 20 GND
8 DATA6 21 GND
9 DATA7 22 GND
10
A
CKNOWLEDGE# 23 GND
11 BUSY 24 GND
12 PAPER EMPTY 25 GND
13 PRINTER SELECT 26 N/C
USB01, USB23: Internal USB Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC(+5V) 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC(+5V)
J_AUDIO1 : Audio Source Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 AC97_SYNC 2 AC97_BITCLK
3 AC97_SDOUT 4 AC97_PCBEEP
5 AC97_SDIN 6 AC97_RST#
7 AC97_VCC 8 AC97_GND
9 AC97_12V 10 AC97_GND
SATA1 & SATA2 : Serial ATA Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 5 RX-
2 TX+ 6 RX+
3 TX- 7 GND
4 GND 8 N/C
IR1: Infrared Interface
connector
PIN NO. DESCRIPTION
1 VCC
2 NC
3 IR-RX
4 GND
5 IR-TX
CPU_FAN1 : CPU Fan Connector
PIN NO. DESCRIPTION
1 Ground
2+12V(PWM)
3FANIO1

10
IDE1 : IDE Interface Connecto
r
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RESET# 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 IDE DRQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IDE CHRDY 28 BALE
–
DEFAULT
29 IDE DACK 30 GND
31 INTERRUPT 32 N/C
33 SA1 34 PDIAG#
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE# 40 GND
41 VCC 42 VCC
43 GND 44 N/C
TV1: Video output for television
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2
A
GREEN_Y
3 GND 4
A
RED_C
RCA Connector (only video signal)
5 GND 6
A
BLUE_CVBS
DIO1 : Digital Input / Output Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 Ground 2 VCC
3 Output 3 4 Output 2
5 Output 1 6 Output 0
7 Input 3 8 Input 2
9 Input 1 10 Input 0