IEI Technology KINO-EHL-J6412 User manual

Mini-ITX SBC Supports Intel® Celeron® J6412 on-board SoC with
HDMI, DP, iDPM, 2.5GbE LAN, M.2, PCIe x4 Slot, SATA 6Gb/s,
COM, USB 3.2 Gen 2, iAUDIO, 0°C~60°C and RoHS
KINO-EHL-J6412
Quick Installation Guide
Version 1.0
June 9, 2022
Package List
KINO-EHL-J6412 package includes the following items:
 1 x KINO-EHL-J6412 single board computer
 1 x SATA cable
 1 x I/O shielding
 1 x QIG
©2022 Copyright by IEI Integration Corp.
All rights reserved.

2
Specifications
 CPU:
Intel® Celeron® J6412 on-board SoC
(up to 2.6GHz, quad-core, 1.5M cache, TDP=10W)
 Memory:
On-board 8GB 3200 MHz LPDDR4X (system max. 16GB)
 BIOS:
AMI UEFI BIOS
Dual BIOS for boot & recovery
 Graphics Engine:
Intel® Gen11LP Gfx firmware and driver, Media SDK,
OpenCL* 1.2, OpenGL 4.5, OpenGL-ES 3.2, Vulkan v1.1,
DirectX
 Display Output:
Triple independent display
1 x HDMI 1.4 (up to 4096 x 2160@30Hz)
1 x DP 1.4 (up to 4096 x 2160 @60Hz)
1 x IEI iDPM 3040 slot (only for IEI eDP/LVDS/VGA module)
 Ethernet:
2 x PCIe 2.5GbE with Intel® I225V
 External I/O Interface:
2 x USB 3.2 Gen 2x1 Type-A (10Gb/s)
2 x USB 2.0 Type-A
2 x RS-232
 Internal I/O Interface:
1 x SATA 6Gb/s with 5V SATA power connector
4 x USB 2.0 (2x4 pin, p=2.0)
4 x RS-422/485 (1x4 pin, p=2.0)
 I
2C:
1 x I
2C (1x4 pin, p=1.25)
 SMBus:
1 x SMBus (1x4 pin, p=1.25)

3
 Audio:
1 x iAUDIO (2x5 pin), supporting IEI AC-KIT-888S kit
 Front Panel:
1 x Front panel (2x7 pin, p=2.54; power LED, HDD LED, power
button, reset button)
 Expansions:
1 x M.2 2230 A key
(PCIe x1 / USB 2.0 signal)
1 x M.2 3052/3042/2242/2280 B key with SIM slot
(PCIe x2 / USB 2.0 signal)
1 x PCIe x4, open-ended (PCIe Gen3 x1 signal)
 Digital I/O:
1 x 12-bit digital I/O (2x7 pin, p=2.0)
 TPM: Intel® PTT (TPM 2.0)
 Fan Connectors:
1 x CPU fan connector (1x4 pin, p=2.54)
1 x System fan connector (1x3 pin, p=2.54)
 Power Supply:
12V DC input
1 x Internal power connector (2x2 pin)
1 x External DC power jack (Ø5.5mm)
ErP/EuP Compliant
 Power Consumption:
[email protected] (Intel® Celeron® J6412 2.0GHz with 8GB
3200MHz LPDDR4X memory and EUP enabled)
 Watchdog Timer:
Software programmable support 1–255 sec. system reset
 Operation Temperature: 0°C – 60°C
 Storage Temperature: -30°C – 70°C
 Operation Humidity: 5% – 95%, non-condensing
 Dimensions: 170 mm x 170 mm
 Weight: GW:900 g / NW:400 g
 Certification: CE/FCC compliant

4
Ordering Information
 KINO-EHL-J6412-R10:
-ITX SBC supports Intel® Elkhart Lake Celeron® J6412 onboard SoC
with triple independent display, HDMI, DP, iDPM, SATA 6Gb/s, dual
2.5GbE, USB 3.2, M.2, 12V DC input and RoHS
 CB-USB02A-RS:
Dual-port USB cable with bracket, 300mm, p=2.0
 AC-KIT-888S-R10:
Realtek ALC888S 7.1 Channel HD Audio peripheral board, RoHS
 32102-000100-200-RS:
SATA power cable, MOLEX 5264-4P to SATA15P
 32205-003800-200-RS:
RS-232/422/485 cable, 200mm, p=2.0
 iDPM-eDP-R10:
eDP to eDP converter board (for IEI iDPM slot)
 iDPM-LVDS-R10:
eDP to LVDS converter board (for IEI iDPM slot)
 iDPM-VGA-R10:
eDP to VGA converter board (for IEI iDPM slot)
All the drivers and utility for the
KINO-EHL-J6412 are available on IEI
Resource Download Center. Type
KINO-EHL-J6412 and press Enter to find
all the relevant software, utilities, and
documentation. To install software from
the downloaded ISO file, mount the file
as a virtual drive to view its content.
IEI Resource Download Center
https://download.ieiworld.com

5
Jumpers Setting and Connectors
LABEL FUNCTION
J_CMOS2 Clear CMOS button
J_ATX_AT1 AT/ATX power mode setting switch
J_BIOS1_1 BIOS1/BIOS2 select jumper
J_DNX1 DNX mode setting jumper
J_FLASH1 Flash descriptor override setting jumper
IAUDIO1 Audio connector for IEI AC-KIT-888S kit
CN3 ATX 12V power connector
BAT1 Battery connector
BZ1 Buzzer connector
DIO1 Digital I/O connector
CPU_FAN1, SYS_FAN2 Fan connectors
F_PANEL1 Front panel connector
PWR_SW1 Onboard power button
COM3, COM4,
COM5, COM6 RS-422/485 serial port connectors
S_ATA1 SATA 6Gb/s connectors
SATA_PWR1 SATA power connector
I2C1 I2C connector
SMB1 SMBus connector
JBIOS1 Flash SPI ROM connector
JEC2 Flash EC ROM connector
J_CONSOLE1 BIOS debug connector
DEBUG_SPI1 EC debug connector
DBG_PORT1 EC SMBus debug port connector
EC_UART1 EC UART debug port connector

6
JUSB3, JUSB4 Internal USB 2.0 connectors
M2_A_KEY M.2 A-key slot
M2_B_KEY M.2 B-key slot
PCIEX4_1 PCIe x4 slot (x1 signal)
CN4 SIM slot (solder side)
IDPM1 IEI iDPM slot
CN2 External 12V DC input jack
J_LAN1_USB1 External 2.5GbE and USB 3.2 Gen 2 combo
connector
J_LAN2_USB2 External 2.5GbE and USB 2.0 combo connecto
r
COM1 External dual RS-232 connector
HDMI_DP1 External HDMI and DP combo connector
J_CMOS2: Clear CMOS Button
PIN NO. DESCRIPTION
NC (default) Keep CMOS Setup
(Normal Operation)
Press button Clear CMOS Setup
J_ATX_AT1: AT/ATX Power Mode Setting Switch
PIN NO. DESCRIPTION
Short A - B ATX Power Mode (default)
Short B - C AT Power Mode
J_BIOS1_1: BIOS1/BIOS2 Select Jumper
PIN NO. DESCRIPTION
Short 1 - 2 BIOS1 (default)
Short 2 - 3 BIOS2

7
J_DNX1: DNX Mode Setting Jumper
PIN NO. DESCRIPTION
Open Normal (default)
Short Enable DNX Boot
J_FLASH1: Flash Descriptor Override Setting Jumper
PIN NO. DESCRIPTION
Short 1 - 2 Disable (default)
Short 2 - 3 Enable
IAUDIO : Audio Connector for IEI AC-KIT-888S Kit
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 HDA_SYNC 2 HDA_CLK
3 HDA_SDOUT 4 HDA_SPKR
5 HDA_SDIN 6 HDA_RST#
7 +5V 8 GND
9 +12V 10 GND
CN3: ATX 12V Power Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 +12V
2 GND 4 +12V
BAT1: RTC Battery Connector
PIN DESCRIPTION PIN DESCRIPTION
1 VBATT 2 GND
BZ1: Buzzer Connector
PIN DESCRIPTION PIN DESCRIPTION
1 +5V 2 PC_BEEP

8
DIO1: Digital Input/Output Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 VCC
3 DOUT5 4 DOUT4
5 DOUT3 6 DOUT2
7 DOUT1 8 DOUT0
9 DIN5 10 DIN4
11 DIN3 12 DIN2
13 DIN1 14 DIN0
CPU_FAN1: Fan Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 FANIO
2 +12V 4 PWM
SYS_FAN2: Fan Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 FANIO 3 GND
2 PWM
F_PANEL1: Front Panel Connector
PIN DESCRIPTION PIN DESCRIPTION
PWR
LED
1 PWR_LED+ 2 SPKR+
SPKR
3 NC 4 NC
5 PWR_LED- 6 NC
PWR
BTN
7 PWR_BTN+ 8 SPKR-
9 PWR_BTN- 10 NC
HDD
LED
11 HDD_LED+ 12 Reset+ RESET
13 HDD_LED- 14 Reset-

9
COM3, COM4, COM5, COM6: RS-422/485 Serial Port Connectors
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RX- 3 TX+
2 RX+ 4 TX-
S_ATA1: SATA 6Gb/s Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 5 SATA_RX‐
2 SATA_TX+ 6 SATA RX+
3 SATA_TX‐ 7 GND
4 GND 8 N/C
SATA_PWR1: SATA Power Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +5V 2 GND
I2C1: I2C Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 I2C_CLK
2 I2C_DATA 4 +5V
SMB1: SMBus Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 3 SMB_CLK
2 SMB_DATA 4 +5V
JBIOS1: Flash SPI ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 4 SPI_CLK
2 SPI_CS# 5 SPI_SI
3 SPI_SO 6 GND

10
JEC2: Flash EC ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 SPI_CS# 2 +3.3V
3 SPI_SO 4 NC
5 EC_DET_FLASH 6 SPI_CLK
7 GND 8 SPI_SI
J_CONSOLE1: BIOS Debug Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 4 PSE_UART4_CTS
2 PSE_UART4_TX 5 PSE_UART4_RTS
3 PSE_UART4_RX 6 GND
DEBUG_SPI1: EC Debug Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 NC 4 EDICLK
2 EDICS 5 EDIDI
3 EDIDO 6 GND
DBG_PORT1: EC SMBus Debug Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +V5A 4 SMDAT0_EC
2 SMCLK0_EC 5 GND
3 NC 6 PLT_RST_N
EC_UART1: EC UART Debug Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 UART_TX 3 UART_RX
2 +3.3V 4 GND