IEI Technology POCm-W22C-ULT3 User manual

Medical Panel PC with 6th Gen. Intel® Core™ / Celeron® CPU,
4 GB DDR4 RAM, Wi-Fi 802.11a/b/g/n/ac, P-CAP Touchscreen,
Three Battery Bays, 5-Megapixel Camera and Microphone
POCm-W22C-ULT3
POCm-W24C-ULT3
Quick Installation Guide
Version 1.01
©2018 Copyright by IEI Integration Corp.
All rights reserved.

1
Revision
Date
Version
Changes
September 11, 2018 1.01 Minor update
August 28, 2018 1.00 Initial release
Intended Use
The POCm-W22/24C-ULT3 medical panel PC is intended to be used to display
general purpose medical images. The device shall not be used for diagnosis
purpose or life supporting system.
Equipment connected to analog or digital interfaces must comply with the respective
IEC Standards (e.g. IEC 60950 for data processing equipment and IEC 60601-1 for
medical equipment). Furthermore all configurations shall comply with the current
version of the standard for SYSTEMS IEC 60601-1-1. Everybody who connects
additional equipment to the signal input part or signal output part configure a
medical system, and is therefore responsible that the system complies with current
version of the requirements of the system standard IEC 60601-1-1. If in doubt,
consult the technical service department or your local representative.
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any
directions or instructions contained therein can help avoid making
mistakes.
OPERATING INSTRUCTION
Follow operating instructions or consult instructions for use.
IEC 60417-5009: Stand-by
IEC 60417-5031: Direct current

2
Overview
The POCm-W22/24C-ULT3 is a 6th generation Intel® Core™ i5-6300U
processor powered medical-grade panel PC with a rich variety of functions
and peripherals. All POCm-W22/24C-ULT3 models are designed for easy
and simplified integration into point-of-care (POC) applications. The system
comes with 4 GB of preinstalled DDR4 memory and supports a maximum
of 32 GB ensuring smooth data throughputs with reduced bottlenecks and
fast system access.
Two RS-232/422/485 serial ports, four USB 3.0 ports and two USB 2.0
ports provide simplified connectivity to a variety of external peripheral
devices. Wi-Fi 802.11a/b/g/n/ac high speed wireless and two RJ-45 GbE
connectors allow for smooth connection of the system to an external LAN.
Three hot-swappable battery bays allow installation of three batteries to
provide continuous power for 8~16 hours.

3
Front Panel
Bottom Panel

4
Side Panel
Rear Panel

5
System Specifications
POCm-W22C-ULT3
POCm-W24C-ULT3
LCD and Touchscreen
LCD Size 21.5" (16:9) 23.8" (16:9)
Max. Resolution
1920 (W) x 1080 (H)
1920 (W) x 1080 (H)
Brightness (cd/m2)
250
250
Contrast Ratio
1000:1
1000:1
LCD Color
16.7M (RGB 6-bit)
16.7M (RGB 6-bit + Hi-FRC)
Pixel Pitch (mm)
0.24825 (H) x 0. 24825 (V)
0.2745 (H) x 0. 2745 (V)
Viewing Angle (H-V)
170°/160°
178°/178°
Backlight MTBF
30,000 hrs (LED backlight)
30,000 hrs (LED backlight)
Touchscreen
Projected capacitive type with USB interface
Multi-touch
10-point touch
Touch Controller
EETI
Surface Hardness
6H
System
CPU
Intel® Celeron® 3855U / Intel® Core™ i5-6300U /
Intel® Core™ i7-6600U
Memory
Two 260-pin 2133/1866 MHz dual-channel non-ECC
unbuffered DDR4 SO-DIMMs supported (system max.
32 GB)
Preinstalled with 4 GB memory
GbE Controller
LAN1: Intel I211 Ethernet controller
LAN2: Intel® I219 Ethernet controller
I/O Ports
1 x DC input jack
2 x HDMI output connector
2 x GbE LAN (RJ-45 connector)
2 x RS-232/422/485 serial port (DB-9 connector)
4 x USB 3.0 connectors
2 x USB 2.0 connectors (side panel)
1 x Audio out (side panel)
1 x Mic-in (side panel)
1 x Digital microphone
Storage
One 2.5” SATA 6Gb/s HDD bay
Audio
Two 3 W speakers
Webcam & Microphone
5-megapixel CMOS front-facing camera with auto focus and
digital microphone
Expansion Interface
2 x M.2 M-key 2242/2260/2280 slot (PCIe + SATA) with
RAID
1 x M.2 A-/E-key 2242 slot (PCIe + USB)
1 x Full-size/Half-size PCIe Mini (PCIe + USB)

6
TPM
TPM 2.0 (optional)
Other Features
1 x Power on/off
1 x Brightness up
Function Keys
1 x Brightness down
1 x Volume up
1 x Volume down
1 x Touch lock (clean mode) or LCD on/off
LED Indicators
3 x Battery indicator
1 x Power indicator
Cooling Method
Fanless
Connectivity
Wi-Fi and Bluetooth 802.11a/b/g/n/ac dual band, Bluetooth v4.2
(M.2 2230 module, Intel® 8265)
LAN
Two GbE LAN connectors
Physical
Construction Material
PC+ABS plastic with anti-bacterial material
Mounting Wall and stand mounting
VESA 75 mm x 75 mm or 100 mm x 100 mm
Dimensions (W x H x D)
543 x 350 x 71 (mm)
594.6 x 379.6 x 71 (mm)
Net Weight
7.07 kg
8.18 kg
Environment
Storage/Transportation
Temperature
-20ºC ~ 60ºC
Humidity
10% ~ 90% (non-condensing)
Pressure
700 hPa ~ 1060 hPa
Operating
Temperature
0ºC ~ 40ºC
Humidity
10% ~ 90% (non-condensing)
Pressure
700 hPa ~ 1060 hPa
Vibration
1G
Shock
Operating Shock: 5G peak acceleration (11ms duration)
Non-Operating Shock: 10G peak acceleration (11ms
duration)
IP Level
IP 65 compliant front panel
Power
Power Input
19 V DC
Power Adapter
150 W FSP FSP150M-ABA medical-grade power adapter
(P/N: 63040-010150-400-RS)
Input: 100 V AC ~ 240 V AC, 50 Hz ~ 60 Hz, 2A ~ 0.85A
Output: 19 V 7.89 A
Battery
3 x Hot-swappable battery bay

7
Installation Precautions
When installing the medical panel PC, please follow the precautions listed
below:
Manufacturer authorization: Do not modify this equipment
without authorization of manufacturer.
Certified Engineers: Only certified engineers should install and
modify the hardware settings.
Power turned off: When installing the medical panel PC, make
sure the power is off. Failing to turn off the power may cause
severe injury to the body and/or damage to the system.
Anti-static Discharge: If a user open the rear panel of the medical
panel PC, to configure the jumpers or plug in added peripheral
devices, ground themselves first and wear an anti-static wristband.
WARNING:
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of
flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in
an explosion or the leakage of flammable liquid or gas.

8
Mounting the System
WARNING:
Use suitable mounting apparatus and be sure to secure the screws of
the mounting apparatus tightly to avoid risk of injury.
NOTE:
When mounting the POCm-W22/24C-ULT3 flat panel PC, it is better to
have more than one person to help with the installation to make sure the
POCm-W22/24C-ULT3 does not fall down and get damaged.
The POCm-W22/24C-ULT3 is VESA (Video Electronics Standards
Association) compliant and can be mounted on a mounting device with a 75
mm or 100 mm interface pad. The POCm-W22/24C-ULT3 VESA mount
retention screw holes are shown below. Refer to the installation guide that
came with the mounting device to mount the POCm-W22/24C-ULT3.

9
Powering On the System
WARNING:
To avoid risk of electric shock, this equipment must only be connected to
supply mains with protective earth.
CAUTION:
The FSP FSP150M-ABA power adapter came with the
POCm-W22/24C-ULT3 is a forming part of the medical device.
Step 1: Connect the power cord to the power adapter. Connect the other
end of the power cord to a power source.
Step 2: Connect the power adapter to the power connector of the
POCm-W22/24C-ULT3.
Step 3: Locate the power button on the right panel.
Step 4: Short press the power button to turn on the POCm-W22/24C-ULT3.
Shutdown Procedure
Turn off the power and disconnect the power cord.
To prevent the risk of electric shock, make sure power cord is
unplugged from wall socket. To fully disengage the power to the unit,
please disconnect the power cord from the AC outlet. Refer servicing to
qualified service personnel. The AC outlet shall be readily available and
accessible.

10
Troubleshooting
If the following situations happen, contact your distributor, sales
representatives or IEI customer service center for technical support.
The HDD is installed correctly, but the POCm-W22/24C-ULT3 is
unable to boot with AC power input after pressing the power button.
Unable to shut down the POCm-W22/24C-ULT3 normally
Please have the following information prepared prior to reporting the
abnormal situations:
Product name and S/N
OS, BIOS version and applications
Acomplete description of the abnormal situation (with photos or video
if available)
System Maintenance
If the components of the POCm-W22/24C-ULT3 fail they must be replaced.
Please contact the system reseller or vendor to purchase the replacement
parts.
Maintenance and Cleaning
Prior to cleaning any part or component of the POCm-W22/24C-ULT3,
please read the details below.
To clean the POCm-W22/24C-ULT3,
oremove dirt with a lightly moistened cloth. Then wipe the external
chassis with a soft dry cloth.
ouse 75% ethanol alcohol to clean the external chassis.
Cleaning frequency: follow the cleaning method guidelines of the
hospital.
Except for the LCD panel, never spray or squirt liquids directly onto
any other components.
The interior of the POCm-W22/24C-ULT3 does not require cleaning.
Keep fluids away from the POCm-W22/24C-ULT3 interior.
Never drop any objects or liquids through the openings of the
POCm-W22/24C-ULT3.

11
Accessories
The medical panel PC is shipped with the following components:
Quantity Item Image
1 POCm-W22/24C-ULT3
medical panel
PC
1 Power cord
(P/N: 32702-000200-100-RS)
1 150 W FSP FSP150M-ABA medical-grade power adapter
(P/N: 63040-010150-400-RS)
4 Round-head screw (M3*3) for HDD installation
(P/N: 44003-030032-RS)
1 Quick Installation Guide
Optional Items
The following components may be separately purchased:
Item and Part Number Image
Li-ion battery pack, 7800 mAh
(P/N: 31603-000069-RS)
Cable cover
(P/N: 43106-0272Q7-00-RS)
20-pin Infineon TPM 2.0 module, software
management tool, firmware v5.5
(P/N: TPM-IN02-R20)

12
DECLARATION OF CONFORMITY
This equipment is in conformity with the following EU directives:
EMC Directive (2004/108/EC, 2014/30/EU)
Low-Voltage Directive (2006/95/EC, 2014/35/EU)
RoHS II Directive (2011/65/EU, 2015/863/EU)
Medical Device Directive 93/42/EEC: EN 60601-1
If the user modifies and/or install other devices in the equipment, the CE
conformity declaration may no longer apply.
If this equipment has telecommunications functionality, it also complies
with the requirements of the Radio Equipment Directive 2014/53/EU.
IEI Integration Corp declares that this equipment is in compliance with the
essential requirements and other relevant provisions of Directive
2014/53/EU.
FCC WARNING
This equipment complies with part 18 of the FCC Rules.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

13
ROHS STATEMENT
The label on the product indicates this product conforms to European
(EU) Restriction of Hazardous Substances (RoHS) that set maximum
concentration limits on hazardous materials used in electrical and
electronic equipment.
CHINA ROHS
The label on the product indicates the estimated “Environmentally
Friendly Use Period” (EFUP). This is an estimate of the number of years
that these substances would “not leak out or undergo abrupt change.”
This product may contain replaceable sub-assemblies/components which
have a shorter EFUP such as batteries and lamps. These components will
be separately marked.

14
Safety Precautions
WARNING:
The precautions outlined below should be strictly followed. Failure to
follow these precautions may result in permanent damage to the
POCm-W22/24C-ULT3.
General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
To prevent the risk of electric shock, make sure power cord is
unplugged from wall socket. To fully disengage the power to the unit,
please disconnect the power cord from the ac outlet. Refer servicing
to qualified service personnel. The AC outlet shall be readily available
and accessible.
Users must not allow SIP/SOPs and the patient to come into contact
at the same time.
Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked “Hospital Only” or
“Hospital Grade”.
Follow the electrostatic precautions outlined below whenever the
POCm-W22/24C-ULT3 is opened.
Make sure the power is turned off and the power cord is disconnected
whenever the POCm-W22/24C-ULT3 is being installed, moved or
modified.
Do not apply voltage levels that exceed the specified voltage range.
Doing so may cause fire and/or an electrical shock. Use a power cord
that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular
country.
Electric shocks can occur if the POCm-W22/24C-ULT3 chassis is
opened when the POCm-W22/24C-ULT3 is running. To avoid risk of
electric shock, this equipment must only be connected to a supply
mains with protective earth.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE
THE EQUIPMENT.
Do not drop or insert any objects into the ventilation openings of the
POCm-W22/24C-ULT3.
If considerable amounts of dust, water, or fluids enter the
POCm-W22/24C-ULT3, turn off the power supply immediately, unplug
the power cord, and contact the POCm-W22/24C-ULT3 vendor.

15
DO NOT:
oDrop the POCm-W22/24C-ULT3 against a hard surface.
oStrike or exert excessive force onto the LCD panel.
oTouch any of the LCD panels with a sharp object
oIn a site where the ambient temperature exceeds the rated
temperature
Product Disposal
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Only certified
engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local regulations.
Outside the European Union - If you wish to dispose of used electrical
and electronic products outside the European Union, please contact
your local authority so as to comply with the correct disposal method.
Within the European Union–The device that produces less waste and
is easier to recycle is classified as electronic device in terms of the
European Directive 2012/19/EU (WEEE), and must not be disposed
of as domestic garbage.
EU-wide legislation, as implemented in each Member State,
requires that waste electrical and electronic products carrying
the mark (left) must be disposed of separately from normal
household waste. This includes monitors and electrical
accessories, such as signal cables or power cords. When you need to
dispose of your display products, please follow the guidance of your local
authority, or ask the shop where you purchased the product. The mark on
electrical and electronic products only applies to the current European
Union Member States.
Please follow the national guidelines for electrical and electronic product
disposal.
Classification
Power by Class I power supply (IEI, POCm-W22/24C-ULT3)
No Applied Part.
No protection against the ingress of water: IPX0
Mode of operation: Continuous Operation

16
The equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide: Not AP or APG
Category.
EMC Test Summary
Guidance and manufacturer’s declaration – electromagnetic emissions
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 should assure that it is used in such an environment.
Emissions test
Compliance
Electromagnetic environment –
guidance
RF emissions
CISPR 11
The model POCm-W22/24C-ULT3
uses RF energy only for its internal
function. Therefore, its RF emissions
are very low and are not likely to
cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11
The model POCm-W22/24C-ULT3 is
suitable for use in all establishments,
including domestic establishments
and those directly connected to the
public low-voltage power supply
network that supplies buildings used
for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Recommended separation distances between portable and mobile RF
communications equipment and the model POCm-W22/24C-ULT3
The model POCm-W22/24C-ULT3 is intended for use in an electromagnetic
environment in which radiated RF disturbances are controlled. The customer or the
user of the model POCm-W22/24C-ULT3 can help prevent electromagnetic
interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the model POCm-W22/24C-ULT3as
recommended below, according to the maximum output power of the
communications equipment.
Rated maximum
output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80
MHz
d= 1,2
80 MHz to 800
MHz
d= 1,2
800 MHz to 2,5
GHz
d= 2,3
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
P
P
P

17
For transmitters rated at a maximum output power not listed above, the
recommended separation distance din metres (m) can be estimated using the
equation applicable to the frequency of the transmitter, where Pis the maximum
output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency
range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
Guidance and manufacturer’s declaration – electromagnetic immunity
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 should assure that it is used in such an environment.
Immunity test
IEC 60601 test
level
Compliance
level
Electromagnetic
environment – guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood,
concrete or ceramic tile.
If floors are covered
with synthetic material,
the relative humidity
should be at least 30 %.
Electrical fast
transient/burst
IEC 61000-4-4
±2 kV for power
supply lines
±1 kV for
input/output
lines
±2 kV for power
supply lines
±1 kV for
input/output
lines
Mains power quality
should be that of a
typical commercial or
hospital environment.
Surge
IEC 61000-4-5
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
Mains power quality
should be that of a
typical commercial or
hospital environment.
interruptions
and
voltage
variations
on power supply
input lines
IEC 61000-4-11
<5 % UT
(>95 % dip in
UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
<5 % UT
(>95 % dip in
UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
Mains power quality
should be that of a
typical commercial or
hospital environment. If
the user of the model
POCm-W22/24C-ULT3
requires continued
operation during power
mains interruptions, it is
recommended that the
model

18
for 25 cycles
<5 % UT
(>95 % dip in
UT)
for 5 sec
for 25 cycles
<5 % UT
(>95 % dip in
UT)
for 5 sec
POCm-W22/24C-ULT3
be powered from an
uninterruptible power
supply or a battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m
3 A/m
Power frequency
magnetic fields should
be at levels
characteristic of a
typical location in a
typical commercial or
hospital environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Guidance and manufacturer’s declaration – electromagnetic immunity
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 should assure that it is used in such an environment.
Immunity
test
IEC 60601
test level
Compliance
level
Electromagnetic environment –
guidance
Conducted
RF
IEC
61000-4-6
Radiated RF
IEC
61000-4-3
3 Vrms
150 kHz to 80
MHz
3 V/m
80 MHz to 2,5
GHz
Vrms
V/m
Portable and mobile RF
communications equipment
should be used no closer to any
part of the model
POCm-W22/24C-ULT3, including
cables, than the recommended
separation distance calculated
from the equation applicable to
the frequency of the transmitter.
Recommended separation
distance
d= 1,2
d= 1,2 80 MHz to 800 MHz
d= 2,3 800 MHz to 2,5 GHz
where Pis the maximum output
power rating of the transmitter
in watts (W) according to the
transmitter manufacturer and d
is the recommended separation
distance in metres (m).
P
P
P

19
Field strengths from fixed RF
transmitters, as determined by
an electromagnetic site survey,
ashould be less than the
compliance level in each
frequency range. b
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
a
Field strengths from fixed transmitters, such as base stations for radio
(cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in
the location in which the model POCm-W22/24C-ULT3 is used exceeds the
applicable RF compliance level above, the model POCm-W22/24C-ULT3 should be
observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as reorienting or relocating the model
POCm-W22/24C-ULT3.
bOver the frequency range 150 kHz to 80 MHz, field strengths should be less than
V/m.
Contact Information
IEI Integration Corp.
No. 29, Zongxing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
TEL: [phone]
Fax: [phone]
www.ieiworld.com
[email protected].tw