Ikan PT4700S-TMW-PEDESTAL User manual

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
PT4700S-TMW-PEDESTAL
Quick Start Guide
17” SDI Teleprompter, Pedestal & Dolly Turnkey w/ 19” Widescreen Talen Monitor Kit
OVERVIEW
Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 17” teleprompter,
pedestal, and dolly. All of our systems have been tested internally for payload compatibility.
The remaining payload capacity, after mounting the full 17” teleprompter without the counterweight, can accommodate camera setups up to
36.5 lbs. The pedestal, without the teleprompter system, can accommodate cameras up to 56.8 lbs. This solution includes a hard case that
features custom-cut foam for the entire teleprompter system. This bundle also includes a separate hard case for the pedestal, and a carrying
bag for the dolly.

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Teleprompter Assmebly Setup
Step 1
Place the teleprompter glass frame on a flat surface and remove the four
screws as shown.
Step 3
The metal frame is directional. Make sure the thicker side is on top and
the slimmer side is on the bottom.
Step 4
Put the washers on before tightening the screws. The washers and 4
additional screws are inside a bag on the bottom foam.
Step 2
Align and attach the teleprompter hood with the 8 screw pegs from the
teleprompter frame.
PT4700S-TMW
17” Professional High Bright
Beam Splitter Teleprompter w/ 19”
Widescreen Talent Monitor (3G-SDI)
What’s Included
1 x Teleprompter Base
1 x Bracket with Glass
1 x Teleprompter Hood with Boot
1 x Monitor
1 x AC Adapters with Cord
1 x PrompterPro Software
1 x Counterweight Set (2 x 2.5 lbs)
2 x D-Ring ¼-20” Screws
2 x Hex Keys
3 x Height Risers
1 x 19” Widescreen Talent Monitor

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Step 6
Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods.
Step 5
Extend the teleprompter hood open and attach teleprompter boot using the clips. It is suggested to align the seam with the bottom of the teleprompter hood.

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Step 8
After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.
Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.
*SAFETY NOTE* Make sure to leave at least 2 inches of the rods inside the teleprompter base.
Teleprompter Base
1
2
-
2
4
V
H
D
M
I
V
G
A
AV
Step 7
Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Step 9
While sliding the teleprompter bracket into the slot of the teleprompter
base pull on the red knob to allow the bracket to fully slide in.
Step 10
Once the bracket is in place, tighten the side screw to lock in place. Double
check and make sure all the screws are tightened with the included hex
keys.
Step 11 (optional)
Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.
** DO NOT THROW AWAY FOAM CASE **
Foam Case
To make your teleprompter more portable, we packed it in a reusable, high-quality foam.
The shape and size of the foam was designed to fit into Ikan’s PT-CASE-V2.

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Monitor Ports
3G-SDI – Serial Digital Interface Connection
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input
HDMI – Switch HDMI input
VGA – Switch to VGA input
SDI – Switch to 3G-SDI input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting
Monitor Menu Settings
Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays
on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit
H
D
M
I
How to set-up FLIP button feature:
1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be
pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both
Horizontal and Vertical flip

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Specifications
PT4700-SDI
Optional Accessories
PT4500-G
PT-CASE-V2
Replacement Glass for both PT4500-SDI / PT4700-SDI
Rolling Hard Case for PT4500-SDI / PT4700-SDI Teleprompter
Aspect Ratio 4:3
Backlight LED
Brightness 1000 nits
Build Material Aluminum
Diagonal 17”
Input Signal 3G-SDI, VGA, HDMI
Input Voltage DC 12v / 4A
Power Consumption 10W
Reading Range 20’
Resolution 1280 x 1024
Viewing Angle 160° (H) / 170° (V)
Weight 23 lb
Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters:
https://youtu.be/5TjIxzBc_Vc
M19-TALENT
Aspect Ratio 19:9
Backlight LED
Brightness 1000 nits
Build Material Aluminum
Diagonal 19”
Input Signal 3G-SDI, VGA, HDMI
Input Voltage DC 12v / 4A
Power Consumption 36W
Reading Range 25’
Resolution 1920 x 1080
Viewing Angle 178° (H) / 178° (V)
Weight 5.73 lb

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too
Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: [email protected]
CONDITIONS OF WARRANTY SERVICE
• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.
Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)
• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.
©2018 ikan Corporation. All rights reserved

19" High-bright Teleprompter LED
Widescreen Monitor w/ Tally
Q ick Start G ide
19” SDI Monitor Compatible with Ikan Teleprompters
www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too
What’s Included
1 x SDI Widescreen Teleprompter Monitor w/ Built-in Tally Light
1 x Power Adapter with Cable
1 x VESA Monitor Mount
1 x 15mm Rod Adapter
1 x Mounting Knob
4 x 10mm Screws
4 x 15mm Screws
2 x Large Screws
4 x Riser Washers
1 x Adjustable Plate

www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too
Monitor Ports
3G-SDI – Serial Digital Interface Connection
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input
HDMI – Switch HDMI input
VGA – Switch to VGA input
SDI – Switch to 3G-SDI input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting
Monitor Menu Settings
Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays
on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit
H
D
M
I
How to set-up FLIP button feature:
1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be
pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both
Horizontal and Vertical flip

Supported Video Signals
SDI
720x480i 59.94, 60 Hz
720x576i 50 Hz
1280x720p 50, 60 Hz
1920x1080i 50, 59.94, 60 Hz
1920x1080psf 24, 25, 29.97, 30 Hz
1920x1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz
HDMI
720x480i & 720x480p 59.94, 60 Hz
720x576i & 720x576p 50 Hz
1280x720p 50, 59.94, 60 Hz
1920x1080i 50, 59.94, 60 Hz
1920x1080psf 24, 25, 29.97, 30 Hz
1920x1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz
Specifications
M 9W
19" High-bright Teleprompter LED Widescreen Monitor w/ Tally
Aspect Ratio 16:9
Brightness 1000 cd/m2
Diagonal 18.5 in.
Input Signal 3G-SDI, VGA, HDMI
Input Voltage DC 12v / 5A
Power Consumption 36W
Product Weight 5.73 lbs.
Product Dimensions 18.3" x 12.3 x 1.2""
Native Resolution 1920 x 1080
Shipping Weight 8 lbs
Shipping Dimensions 16.25” x 14.25” x 2”
Viewing Angle 178° (H) / 178° (V)
Build Material
UPC
Tally Interface
Aluminum Chassis
847983034697
RJ45
www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too

www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too
Assembly Steps
Setting Up the Talent Monitor
Using the shorter 4 x 10mm Screws, attach the VESA Monitor Mount. Make sure that the long end of the VESA Monitor Mount is pointing in the direction
of the power button like the image above. Use the Mounting Knob to tighten the 15mm Rod Adapter to the VESA Monitor Mount. Make sure that the top of
the VESA Mount is flush with the edge of the monitor.
Setting Up the Teleprompter Monitor (Script Monitor from the Teleprompter Base System)
If the mounting brackets where previously installed on the teleprompter monitor, remove those screws. Using the longer 4 x 15mm Screws and 4 x Riser
Washers attach the mounting brackets with the washers between the bracket and monitor like the image below.

www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too
Attaching the Talent Monitor
After both the talent monitor and teleprompter monitor are set up, slide the talent monitor on to the Teleprompter
Base System.
*WARNING* We recommend at least 1 inch of rod should be left inside the teleprompter base.

Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: support ikancorp.com
Pinout Diagram for Tally Light
Tally Light Pinout:
GND: Connects to the ground of the device or system.
R: Connects the red tally light
G: Connects the green tally light
Y: Connects the yellow tally light
NC: Stands for "Not Connected" Disregard these pins.
CONDITIONS OF WARRANTY SERVICE
• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.
Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)
• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.
©2021 Ikan International. All rights reserved.
www.ikancorp.com | 1.713.272.8822 | sales ikancorp.com because we’re filmmakers too

EP880SK Pedestal
Component:
Pedestal
EP880S
EI7007
Dolly
182.0cm
71.7in
102.5cm
182.5in
38.0cm
15.0in
28.5kg
15.0lbs
3.0-28.0kg
6.6-61.7lbs
100mm
High version kit
165.5cm
Standard kit
Extendable column
(extra part)
+
1 2
34
Pneumatic column
pedestal system Air-pressure in the
pneumatic column
can be adjusted
Double-wheel 125mm
casters with adjustable
cable guards
Fluid head with
100mm ball
Fluid head GH25

GH25 100mm Fluid Head
FEATURES
SPECIFICATIONS
Model
Payload Range
Counterbalance Range
Grades Of Pan Drag
Grades Of Tilt Drag
Tilt Range
Temperature Range
Bowl Size
Net Weight
GH25
-40℃~+80℃
100mm
4.2kg / 9.2lbs
Additional standard 1/4" &
3/8" screw holes
15 steps of counterbalance
llluminated leveling bubble
7 plus 0 grades of pan &
tilt drag
1-15
100mm
3.0-28.0kg
6.6-61.7lbs
160mm/6.3in
73mm/2.9in
203mm/8.0in
3.0-28.0kg / 6.6-61.7lbs
1-15
0-7
0-7
-65°/+90°

EP880S Pedestal
Component:
Pedestal
EP880S
EI7007
Dolly
165.0cm
65.0in
86.0cm
33.9in
38.0cm
15.0in
23.9kg
52.7lbs
30.0kg
66.1lbs
100mm
High version kit
165.5cm
Standard kit
Extendable column
(extra part)
+
1 2
34
Pneumatic column
pedestal system Air-pressure in the
pneumatic column
can be adjusted
Ergonomic hand
wheel Double-wheel 125mm
casters with adjustable
cable guards

EI-7007 Super dolly
FEATURES
125mm
Pull the knob to extend the dolly,
easy to go out.
Height : 21.5cm / 8.5in
Radius: 50cm / 19.7in
Casters diameter: 125mm / 4.9in.
The rubber wheels are non-marring
during normal use,protecting the
oor surface.
Each wheel incorporates its own
foot-activated brake.
Cable guards and brakes. Supports up to 100kg of tripod,
camera and accessories.
Payload
100kg
Φ
H
Locking
50cm
21.5cm
Designed for pedestal system and other heavy duty system. The 125mm/5inch wheels with cable guard can be
individually braked, also the movement direction can be fixed.
Folds for transporting.

GB3 Pan bar
Telescopic pan bar for GH08L, GH10L, GH15, GH25 heads
SPECIFICATIONS
Length range
Net weight
405-605mm / 15.9-23.8in
385g / 0.8lbs