Impex saogear MSS-7500 User manual

WEIGHT BENCH
MSS-7500
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MSS-7500
Retain This
Manual for
Reference
06/11/09
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 6
EXPLODED DIAGRAM.................................................................................... 10
PARTS LIST..................................................................................................... 11
WARRANTY..................................................................................................... 12
ORDERING PARTS.......................................................................................... 12
BEFORE YOU BEGIN
Thank you for selecting the SA GEAR WEIGHT BENCH MSS-7500 by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee your complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. This machine is designed and intended for home and consumer use only, not for
commercial use.
14. Maximum user’s weight: 300 lbs.
15. Maximum weight on uprights: 600 lbs.
16. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The Warning Labels shown here have been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Secure
each end of the Cross Brace to Upright Beam with two M10 x 3 ¾” Carriage Bolts (#30),
one 5 ½” Curved Bracket (#13), two Ø ¾” Washers (#36), and two M10 Aircraft Nuts
(#38).
C.)Insert two Crutches (#7) into the openings on the two Upright Beams. Thread a M18
Lock Knob (#16) into the Upright Beam to lock each Crutch at desired height.
D.)Place the Backrest Adjustment Bar (#8) onto the selected peg to obtain the backrest
incline. DIAGRAM 1
6

STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#3) to the Front Post (#4). Secure it with two M10 x 2 3/8”
Carriage Bolts (#32), one 6 ¼” x 3 ¼” Bracket (#14), two Ø ¾” Washers (#36), and two
M10 Aircraft Nuts (#38).
B.) Attach the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 ½”
Carriage Bolts (#31), one 5 ½” x 3” Curved Bracket (#15), two Ø ¾” Washer (#36), and
two M10 Aircraft Nut (#38).
C.) Securely tighten all Nuts and Bolts in Step-1 and Step-2. DIAGRAM 2
7

STEP 3 (See Diagram 3)
A.) Attach the Seat Bracket (#5) to the pivot on the Main Seat Support (#3). Attach the holes
on the end of the two Backrest Supports (#6) to the Seat Bracket. Align the holes. Secure
the two Backrest Supports, Seat Bracket together to the pivot with one M12 x 7” Hex Bolt
(#26), two Ø 1” Washers (#37), and one M12 Aircraft Nut (#39). Do not over tighten the
Nuts and Bolts. Make sure the Backrest Supports are able to swivel.
B.) Attach the Backrest Board (#11) to the Backrest Supports. Secure it with four M8 x 1 5/8”
Allen Bolts (#34) and four Ø 5/8” Washers (#35).
C.) Place the Seat Pad onto the Seat Bracket. Secure it with four M8 x 1 5/8” Allen Bolts (#34)
and four Ø 5/8” Washers (#35). DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#9) to the open bracket on Main Seat Support (#3). Secure it
with one Leg Developer Axle (#21), two M10 x ¾” Allen Bolt (#33), and two Ø ¾” Washers
(#36). Do not over tighten the Bolts. Make sure the Leg Developer is able to swivel.
B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#19) onto the Tubes from both ends. Plug four Foam Roll End Caps (#26)
into the ends.
C.) Slide an Olympic Sleeve (#24) onto the weight post on Leg Developer. Attach a Spring
Clip (#20) onto the Sleeve. DIAGRAM 4
9