Impex Iron Grip Sport IGS-06 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Content
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
IGS-06
Retain This
Manual for
Reference
04-18-02
OWNER'S
MANUAL
IGS-06
CABLE CROSSOVER
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE IDENTIFIER.....…....................................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 4
EXPLODED DIAGRAM……………………………………………………………... 8
PARTS LIST……………………………………………………………………….. 9
WARRANTY.................................................................................................… 10
ORDERING PARTS......................................................................................... 10
BEFORE YOU BEGIN
Thank you for selecting the IRON GRIP SPORT Cable Crossover by
IMPEX FITNESS PRODUCTS. For your safety and benefit, read this
manual carefully before using the machine. As a manufacturer, we are
committed to provide you complete customer satisfaction. If you have any
questions, or find there are missing or damaged parts, we guarantee you
complete satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance
to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench
NOTE: It is strongly recommended this machine to be assembled by two or more
people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach a Floor Stabilizer (#6) and a Lower Pivot Bracket (#35) to the Base Frame
(#3). Secure it with two M12 x 4” Carriage Bolts (#28), ∅1” Washers (#29), and
M12 Aircraft Nuts (#30).
B.) Insert the Lower Pulley Bracket (#14) into the hole on the Lower Pivot Bracket
(#35). Secure it with one M10 x 1” Allen Bolt (#38) and ∅1 ½” Washer (#39).
C.) Repeat the procedure A and B above to install the other side.
DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach a Support Frame (#2) to the Floor Stabilizer (#6). Secure it with one Bracket (#16),
two M12 x 4” Carriage Bolts (#28), ∅1” Washers (#29), and M12 Aircraft Nuts (#30).
B.) Insert two Guide Rods (#12) into the holes on top of the Base Frame (#3). Secure each
Guide Rod with one M10 x 1” Allen Bolt (#38) and ∅¾” Washer (#32) from the bottom.
C.)Slide one 1” Thick Rubber Bumper (#22) onto each Guide Rod from top. Note: WD40 or
similar lubricant might be needed. Slide one Guide Rod Sleeve (#5) onto each Guide Rod
from top. Then slide one more 1” Rubber Bumper (#22) onto each Guide Rod from the top.
D.)Screw a Small Pulley Bracket (#8) to the top of the Weight Holder (#4). Slide the Weight
Holder (#4) onto the two Guide Rods (#12) from the top. Slide one ½” Thick Rubber Bumper
(#23) and Olympic Sleeve (#13) onto the Weight Holder from each end. Clip one Spring Clip
(#25) onto each end of Olympic Sleeve.
E.) Repeat the Step A, B, C, D above to install the other side.
F.) It is strongly recommended to spray lubricant such as WD-40 on the Guide Rods to
minimize friction.
5

STEP 3 (See Diagram 3 & Cable Loop Diagram)
A.) Attach the horizontal beam on the Crossover Frame (#1) to the top of the two Guide
Rods (#12). Note: Help of a second or third person is a must!! Secure the Guide Rods
with two M10 x 1” Allen Bolts (#38) and ∅¾” Washers (#32). Repeat the same
procedure to install the other side.
B.) Secure each end of Crossover Frame to each Rear Support Frame (#2) with one
Bracket (#16), two M12 x 4” Carriage Bolts (#28), two ∅1” Washers (#29), and two
M12 Aircraft Nuts (#30).
C.)Attach an Upper Pulley Bracket (#9) to the horizontal beam on the Crossover Frame
(#1). Secure it with a M10 x 1” Allen Bolt (#38) and ∅1 ½” Washer (#39). Repeat the
same step to install the other side.
D.)Attach the Cable (#20) to the Lower Pulley Bracket (#14). Attach a 6” Pulley (#18) to
the Bracket. Secure it with one M10 x 2” Allen Bolts (#31), two ∅¾” Washers (#32),
and one M10 Aircraft Nut (#33).
E.) Pull the Cable (#20) to the open bracket on the Floor Stabilizer (#6). Repeat Step D
above to install a 6” Pulley (#18).
F.) Pull the Cable upward towards the open pulley bracket on the Crossover Frame (#1).
Install another 6” Pulley (#18).
G.)Draw the Cable downward to the Small Pulley Bracket (#8) on the Weight Holder (#4).
Install a 4 ½” Pulley (#19) to the bracket.
H.)Pull the Cable upward to the Upper Pulley Bracket (#9). Install a 6” Pulley.
I.) Repeat the steps above to install the other side.
J.) Attach a C-clip (#37) to the end of the Cable. Attach one end of a Chain (#36) to the C-
clip and the other end to the Handle. Repeat to install the other three handles.
6

DIAGRAM 3
7

8

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Crossover Frame 1
2 Support Frame 2
3 Base Frame 2
4 Weight Holder 2
5 Guide Rod Sleeve 4
6 Floor Stabilizer 2
7 Allen Bolt 4
8 Small Pulley Bracket 2
9 Large Upper Pulley Bracket 2
10 ∅1” x 1 ½” Brass Bushing 2
11 Handle 4
12 Guide Rod 4
13 Olympic Sleeve 4
14 Lower Pulley Bracket 2
15 ∅1” x ¾” Brass Bushing 4
16 Bracket 4
17 Chin Up Grip 2
18 6” Pulley 8
19 4 ½” Pulley 2
20 Cable 2
21 M10 x 1” Round Allen Bolt 8
22 1” Thick Rubber Bumper 8
23 ½” Thick Rubber Bumper 4
24 Olympic Sleeve End Cap 4
25 Spring Clip 4
26 Spring Clip Sleeve 8
27 Horse Shoe End Cap 8
28 M12 x 4” Carriage Bolt 12
29 ∅1” Washer 12
30 M12 Aircraft Nut 12
31 M10 x 2” Allen Bolt 10
32 ∅¾” Washer 28
33 M10 Aircraft Nut 10
34 2” x 2 ¾” End Cap 4
35 Lower Pivot Bracket 4
36 Chain 2
37 C-clip 8
38 M10 x 1” Allen Bolt 12
39 ∅1 ½” Washer 4
40 Cone-shaped End Cap 2
41 Plastic Bushing 8
9