Impex MARCY DIAMOND ELITE MD-843 User manual

MARCY®DIAMOND
ELITE
WEIGHT BENCH
MD-843
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: [phone] Fax [phone]
www.impex-fitness.com
[email protected]
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MD-843
Retain This
Manual for
Reference
07/15/09
OWNER'S
MANUAL

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 6
EXPLODED DIAGRAM.................................................................................... 12
PARTS LIST..................................................................................................... 13
WARRANTY..................................................................................................... 14
ORDERING PARTS.......................................................................................... 14
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND ELITE WEIGHT BENCH MD-
843 by IMPEX®INC. For your safety and benefit, read this manual carefully
before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee your complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The Warning Labels shown here have been placed on the Base Frame. If the label i
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach one Rear Base Frame (#1) to an Upright Beam (#3) from rear. Attach one end of
the Base Frame (#2) to the Upright Beam from front. Align the holes. Secure them
together with three M10 x 3 ¾” Carriage Bolts (#37), three Ø ¾” Washers (#40), and
three M10 Aircraft Nuts (#31). Secure with two M10 x 5/8” Allen Bolts (#34) from inside
of Upright Beam into Rear Base Frame and Base Frame.
C.)Repeat B to install the other side.
D.)Attach the two Bar Catches (#5) and two Long Safety Catches (#4) onto the selected
slots on the Upright Beams.
E.) Insert the Backrest Adjustment Bar (#7) into the selected holes on the two Upright
Beams to obtain the desired Backrest Incline.
F.) Securely tighten all Nuts and Bolts.
6

DIAGRAM 1
7

STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#6) to the Base Frame (#2). Secure it with two M10 x 3 ¾”
Carriage Bolts (#37), one 5 ½” Curved Bracket (#12), two Ø ¾” Washers (#40), and two
M10 Aircraft Nuts (#31). Do not tighten the Nuts and Bolts yet.
B.) Attach the Front Post (#9) to the Main Seat Support. Secure it with one M10 x 3 1/8” Allen
Bolt (#35) through upper hole on 4” Curved Bracket (#13), and one Ø ¾” Washer (#40)
into Main Seat Support. Secure with one M10 x 3 1/8” Carriage Bolts (#36), one Ø ¾”
Washer (#40), and one M10 Aircraft Nut (#31) through lower hole on the Bracket.
C.) Securely tighten all Nuts and Bolts.
D.) Attach the end holes on the two Backrest Supports (#8) to the pivot on Main Seat Support.
Secure it with one M12 x 5 7/8” Hex Bolt (#38), two Ø 1” Washers (#41), and one M12
Aircraft Nut (#30). Do not over tighten the Nut and Bolt. Make sure the Backrest
Supports are able to swivel freely.
E.) Place the other end of the Backrest Supports onto the Backrest Adjustment Bar (#7).
DIAGRAM 2
8

STEP 3 (See Diagram 3)
A.) Attach the Backrest Board (#14) to the Backrest Supports (#8). Secure it with four M8 x 1
5/8” Allen Bolts (#32) and four Ø 5/8” Washers (#39).
B.) Place the Seat Pad (#15) onto the seat brackets on Main Seat Support (#6). Secure it with
four M8 x 1 5/8” Allen Bolts (#32), and four Ø 5/8” Washers (#39).
C.) Attach the Arm Curl Pad (#16) to the Arm Curl Stand (#11). Secure it with two M8 x 5/8”
Allen Bolts (#33) and two Ø 5/8” Washers (#39). Insert the Arm Curl Stand into the
opening on Front Post (#9). Use a M10 Lock Knob (#21) to lock the Arm Curl Stand in
position. DIAGRAM 3
9