Impex MARCY DIAMOND ELITE MD-856 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-856
Retain This
Manual for
Reference
07-26-05
OWNER'S
MANUAL
MARCY DIAMOND ELITE
OLYMPIC SURGE BENCH
MD-856
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 4
ASSEMBLY INSTRUCTIONS.........................................................................……….. 6
EXPLODED DIAGRAM…………………………………………………………………….. 11
PARTS LIST………….………….......................................................................………. 12
WARRANTY.................................................................................................…………. 13
ORDERING PARTS.......................................................................................………… 13
BEFORE YOU BEGIN
Thank you for selecting the Marcy Diamond Elite MD-856 BENCH by
IMPEX INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please
call our TOLL-FREE customer service number. Our Customer Service
Agents will provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum weight capacity 600 lbs (include user’s weight).
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown
3

HARDWARE PACK
4

HARDWARE PACK
5

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Note: Do not tighten all nuts and bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to a Rear Stabilizer (#3). Secure it with two M10 x 5/8” Allen
Bolts (#63), and Ø ¾” Washers (#66).
C.) Attach the bottom of the Rear Diagonal Support (#8) to the Rear Stabilizer. Secure it with one
M10 x 3 ¾” Allen Bolt (#60), two Ø ¾” Washers (#66), and one M10 Aircraft Nut (#68). Attach
the top of the Rear Diagonal Support (#8) to the Left Upright Beam (#1). Secure it with two
M10 x 5/8” Allen Bolts (#63) and Ø ¾” Washers (#66).
D.) Repeat Steps A, B, and C above to install the Right side.
E.) Connect the Left & Right Upright Beams with a Cross Brace (#5) in the mid-span. Secure each
end with two M10 x 3 ½” Carriage Bolts (#56), one Bracket (#23), two Ø ¾” Washer (#66), and
two M10 Aircraft Nut (#68). Securely tighten all Nuts and Bolts previously installed.
F.) Place the Backrest Adjustment Bar (#6) onto the selected slot between the Upright Beams.
6

STEP 2 (See Diagram 2)
A.) Slide the Sliding Block (#15) onto the Main Seat Support (#4). Thread a Lock Knob (#42)
into the selected hole to hold the Sliding Block in position.
B.) Attach the Leg Developer Holder (#13) to the Front Stabilizer (#14). Secure it with three
M10 x 5/8” Allen Bolts (#63) and ∅¾” Washers (#66).
C.) Attach the Main Seat Support (#4) to the Leg Developer Holder (#13). Secure it with one
M10 x 2 ½” Carriage Bolt (#58) from the top, two M10 x 2 ¾” Carriage Bolts (#57) from the
side, three ∅¾” Washers (#66) and three M10 Aircraft Nuts (#68).
D.) Attach the Main Seat Support (#4) to the Cross Brace (#5). Secure it with two M10 x 2 3/8”
Carriage Bolts (#59), one Bracket (#23), two ∅¾” Washers (#66), and two M10 Aircraft
Nuts (#68).
E.) Attach the two Squat Bar Catches (#7) to the back of the two Upright Beams. Secure each
Catch with a 4 ½” L-shaped Pin (#51).
F.) Insert a Weight Post (#24) into the hole on the Rear Diagonal Support (#8). Secure it with
one M10 x ¾” Allen Bolt (#62) and Ø ¾” Washer (#66). Slide an Olympic Sleeve (#30) onto
the Weight Post. Repeat for the other side.
G.)Insert the Left & Right Bar Catches (#16 &17), Left & Right Safety Catches (#18 &19) into
the selected holes on the Upright Beams (#1 & 2).
7

STEP 3 (See Diagram 3)
A.) Attach the holes on the end of the Backrest Supports (#21) to the long pivot on the Sliding
Block (#15). Attach the Backrest Board (#26) to the Backrest Supports. Secure it with
four M8 x 1 5/8” Allen Bolts (#65) and Ø5/8” Washers (#67). Place the Backrest Board
rest against the Backrest Adjustment Bar.
B.) Attach the Seat Bracket (#20) to the short pivot on the Sliding Block. Secure it with one
M10 x 4 ¾” Allen Bolt (#61), two Ø ¾” Washers (#66), and one M10 Aircraft Nut (#68).
C.) Place the Seat (#27) onto the Seat Bracket. Secure it with four M8 x 5/8” Allen Bolts
(#64) and Ø 5/8” Washers (#67).
D.) Insert a 4” L-shaped Pin (#53) into the selected hole on the Seat Bracket to obtain the
desired Seat inclined position. DIAGRAM 3
8

STEP 4 (See Diagram 4)
A.) Insert the U-shaped Pin (#49) into the open slot on the Leg Developer Holder (#13). Secure
it with one M6 x ½” Philips Screw (#47), Ø ½” Washer (#48), and Spring (#50).
B.) Attach the Leg Developer (#10) to the Leg Developer Holder. Secure it with an Axle (#55),
two M10 x 5/8” Allen Bolts (#63) and two ∅¾” Washers (#66).
C.) Insert one Foam Tube (#22) halfway through the hole on the Leg Developer Holder. Insert
two Foam Tubes halfway through the holes on the Leg Developer. Push six Foam Rolls
(#31) onto the Tubes from both ends. Plug six Foam Roll End Caps (#32) into the ends.
D.) Slide an Olympic Sleeve (#30) onto the weight post on the Leg Developer. Attach a Spring
Clip (#54) to the Sleeve. DIAGRAM 4
9