Infineon Traveo II CPU board User manual

www.infineon.com
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
The fact that Infineon offers the following product as part of the Infineon product
portfolio.
Continuity of document content
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.

CYTVII-B-H-4M-176-CPU board quick start guide
Traveo™ II CPU board
Kit contents:
1. Traveo™ II CPU board (CYTVII-B-H-4M-176-CPU)
2. Type-B Mini USB cable
3. 12V AC-DC universal power adapter
4. Quick start guide (this document)
5. Screws and spacers

Traveo™ II CPU board
• Ensure that the MCU reset controller jumper (J18) is
inserted.
CYTVII-B-H-4M-176-CPU board quick start guide
•Ensure that jumpers J7, J6, J5, J11, J9, J41, J42 are
inserted. Ensure that jumpers J8, J45, J10 are in
1-2 position and J46 is in 2-3 position.
•Connect an appropriate programming tool (IAR/GHS) to
one of the debugging interfaces (J21, J20, J22, J19).
• Use an appropriate IDE on a PC to load a rmware SREC le into the device ash. The LED blink rmware is available
in the release package.
• Connect the 12V adapter to power jack (J1). Toggle the
switch SW1 to the ON position to power up the board.
12
4
3

CYTVII-B-H-4M-176-CPU board quick start guide
• User guide
•Schematic
• Sample driver library (SDL)
• Software examples
Instructions:
Use the board in conjunction with the body controller baseboard (CYTVII-B-E-BB) to evaluate all features of the
Traveo™ II MCU. In standalone mode, only limited features of the MCU are available.
Traveo™ II CPU board
CYTVII-B-E-BB CYTVII-B-H-4M-176-CPU
See the CPU board user guide for details.
Go to the customer support portal (cypress.com/support) to know more about the baseboard and
compatibility, and for the following resources:

CYTVII-B-H-4M-176-CPU board quick start guide
Traveo™ II CPU board
Traveo™ II CPU board details
1. MCU reset controller jumper – J18
2. MCU reset LED – LED6
3. MCU reset button – SW5
4. User LEDs – LED4 & LED5
5. Jumpers for user LEDs – J16 & J17
6. Automotive Ethernet controller (TJA1100) – U6
7. Automotive Ethernet connector – J27
8. Hibernate mode switch – SW3
9. IDC Arm®standard JTAG 20-Pin connector – J21
10. Arm®Cortex®debug MIPI-10 connector – J20
11. Arm®Cortex®debug ETM MIPI-20 connector – J22
12. Arm®ETM Mictor–38 connector – J19
13. User switches – SW2 & SW4
14. Jumpers for user switches – J13 & J15
15. Jumpers for SMIF – R155, R157, R169, R170
16. Jumpers for SDHC – R197 to R202
17. 512Mb HyperFlash™ memory (S26KL512) – U15
18. 64Mb HyperRAM™ DRAM (S27KL064) – U16
19. 256Mb Quad–SPI ash (FL256Sx) – U19, U20
20. SDHC card connector – U14
21. LDO for audio 1.8V (NCP1117) – U10
22. 3.5mm audio jack – J29
23. Audio codec (TLV320AIC26) – U9
24. Mini-B USB connector – J25
25. UART Rx and Tx LEDs – LED8, LED9
26. CPU board power switch – SW1
27. Power connector – J1
28. USB serial controller (CY7C65213) – U5
29. UART Rx and Tx jumpers – J24, J26
30. PMIC controller board – ET1, ET2
31. Traveo™ II TVII–B–H–4M device (CYT4BB) – U3
32. MCU power jumpers – J5 to J11, J45
33. MCU power LEDs – LED1, LED2, LED3
1
2
3
4
5
6
7
8
9
10
11 12 13 14 171615 18 19
20
21
22
23
24
25
26
27
282930313233
© 2020-2021 Cypress Semiconductor Corporation, an Inneon Technologies
Company. All rights reserved. All trademarks or registered trademarks referenced
herein are the property of their respective owners. 002-30059 Rev.*A