Infineon KIT T2G-B-E LITE User manual

User Guide Please read the Important Notice and Warnings at the end of this document 002-37239 Rev. **
www.infineon.com 2023-07-20
KIT_T2G-B-E_LITE user guide

Scope and purpose
This document serves as a guide for using the KIT_T2G-B-E_LITE. This document explains the kit operation,
describes the Sample Driver Library (SDL) and its operation, and the hardware details of the board.
Intended audience
This document is intended for KIT_T2G-B-E_LITE users.
Reference documents
This user guide should be read in conjunction with the following documents:
•AN220118 - Getting started with 
•Entry (CYT2BL series) datasheet

User Guide 2 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Table of contents

About this document....................................................................................................................... 1
Table of contents............................................................................................................................ 2
Safety and regulatory compliance information .................................................................................. 3
General safety instructions.............................................................................................................. 3
1Introduction .......................................................................................................................... 4
1.1 Getting started.........................................................................................................................................4
1.2 Additional learning resources.................................................................................................................4
1.3 Technical support....................................................................................................................................5
1.4 Documentation conventions ..................................................................................................................5
1.5 Abbreviations and definitions.................................................................................................................5
2Kit details.............................................................................................................................. 7
2.1 Kit contents .............................................................................................................................................7
2.2 Board details ...........................................................................................................................................7
3Kit operation ........................................................................................................................13
3.1 Theory of operation...............................................................................................................................13
3.2 KitProg3: Onboard programmer/debugger .........................................................................................17
3.2.1 Programming and debugging using TRAVEO™ T2G Sample driver library software.....................17
3.2.2 USB-UART bridge .............................................................................................................................19
4Hardware .............................................................................................................................20
4.1 KIT_T2G-B-E_Lite Kit Connections .......................................................................................................20
4.1.1 USER LEDs ........................................................................................................................................20
4.1.2 USER switches..................................................................................................................................20
4.1.3 RESET switch....................................................................................................................................20
4.1.4 MODE switch.....................................................................................................................................20
4.2 System Configuration ...........................................................................................................................21
4.3 Schematics ............................................................................................................................................21
4.4 Layouts ..................................................................................................................................................38
Revision history.............................................................................................................................41

User Guide 3 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Safety and regulatory compliance information

This kit is intended for development purposes only. Users are advised to test and evaluate this kit in an RF
development environment.
Safety evaluation for this kit is done in factory default settings using default accessories shipped with the kit. All
evaluations for safety are carried out using a 5-V (USB 2.0, @ 500 mA) supply. Attaching additional wiring to this
product or modifying the product operation from the factory default may affect its performance and cause
interference with other apparatus in the immediate vicinity. If such interference is detected, suitable mitigating
measures should be taken.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all
required authorizations are first obtained. Contact Infineon supportfor details.
These kits contain electrostatic discharge (ESD) sensitive devices.
Electrostatic charges readily accumulate on the human body and any
equipment, which can cause a discharge without detection. Permanent
damage may occur on devices subjected to high-energy discharges. Proper
ESD precautions are recommended to avoid performance degradation or loss
of functionality. Store unused kits in the protective shipping package.
End-of-life/product recycling
The end-of-life cycle for this kit is five years from the date of manufacture
mentioned on the back of the box. Contact your nearest recycler to discard
the kit.

ESD protection
ESD can damage boards and associated components. Infineon recommends that you perform procedures only
at an ESD workstation. If an ESD workstation is unavailable, use appropriate ESD protection by wearing an anti-
static wrist strap attached to the chassis ground (any unpainted metal surface) on your board when handling
parts.
Handling boards
This board is sensitive to ESD. Hold the board only by its edges. After removing the board from its box, place it
on a grounded, static-free surface. Use a conductive foam pad, if available. Do not slide the board over any
surface.

User Guide 4 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Introduction
1
Thank you for your interest in the KIT_T2G-B-E_LITE. The TRAVEO™ T2G Body Entry Lite evaluation kit enables
you to evaluate and develop your applications using the ody Entry MCU (hereafter called
“TRAVEO™ T2G-B-E MCU”).
The TRAVEO™ T2G-B-E MCU is designed for industrial applications and is a true programmable embedded
system-on-chip, integrating up to 160-MHz Arm® Cortex®-M4F as the primary application processors, a 100-MHz
Arm® Cortex®-M0+ that supports low-power operations, up to 4-MB flash and 512-KB SRAM, Secure Digital Host
Controller (SDHC) supporting SD/SDIO/eMMC interfaces, and programmable analog and digital peripherals that
allow faster time-to-market.
The evaluation board features an on-board programmer/debugger (KitProg3), a micro-B connector for the USB
device interface, three user LEDs, one potentiometer, and two push buttons. The board supports operating
voltages from 1.8 V to 5.0 V for the TRAVEO™ T2G-B-E MCU.
You can use ModusToolbox™ software to develop and debug your TRAVEO™ T2G-B-E MCU projects.
 is a set of tools that enable you to integrate these devices into your existing
development methodology.
If you are new to TRAVEO™ T2G-B-E MCU and "Sample Driver Library (SDL)", refer to the application note
AN220118 -  to help you familiarize with the TRAVEO™ T2G-
B-E MCU and help you create your own design using the SDL.
1.1 
This guide helps you to get acquainted with this evaluation kit:
•The Kit details chapter provides the kit and package details and board details.
•The Kit operation chapter describes the major features of the TRAVEO™ T2G-B-E evaluation board and
functionalities such as programming, debugging, and the USB-UART, and USB-I2C bridges.
•The Hardware chapter provides a detailed hardware description, kit schematics, and the bill of materials
(BOM).
•The SDL supports application development using the TRAVEO™ T2G-B-E evaluation kit. The SDL simplified
software development for TRAVEO™T2G devices includes the following:
- Drivers for an extensive set of peripherals.
- Arm® Cortex® Microcontroller Software Interface Standard (CMSIS) core header files directly from the
CMSIS 5.7 release.
- CMSIS compliant device header files, standup code (platform initialization), and device configuration
header files.
- Application programming interface reference manual.
- Examples to evaluate various peripherals.
•SDL is provided as an executable, tested on Windows 10 with a minimum installation size requirement of
around 400 MB.
1.2 
Infineon provides a wealth of data at www.infineon.com/cms/en/product/microcontroller/32-bit-traveo-
t2g-arm-cortex-microcontroller to help you to select the right TRAVEO™ T2G MCU device for your design and
to help you quickly and effectively integrate the device into your design.

User Guide 5 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Introduction
1.3 
For assistance, go to www.infineon.com/support. Visit community.infineon.com to ask your questions in
Infineon developer community.
You can also use the following support resources if you need quick assistance:
•Self-help (Technical documents)
1.4 
Table 1 Document conventions for guides
1.5 
Table 2 Abbreviations
Abbreviation
Definition
ADC
analog-to-digital converter
BOM
bill of materials
CINT
Integration Capacitor
CMOD
Modulator Capacitor
CPU
central processing unit
CSD
capacitive sigma delta
CSX
CAPSENSE™ Crosspoint
CTANK
Shield Tank Capacitor
DC
direct current
ECO
external crystal oscillator
ESD
electrostatic discharge
FPC
flexible printed circuit
GPIO
general-purpose input/output
IC
integrated circuit
IDE
integrated development environment
IoT
Internet of Things
Convention
Usage
Courier New
Displays user-entered text and source code
Italics
Displays file names and reference documentation:
Read about the sourcefile.hex file in the PSoC™Creator user guide.
File > Open
Represents menu paths: File > Open > New Project
Bold
Displays commands, menu paths, and icon names in procedures:
Click the File icon and then click Open.
Times New Roman
Displays an equation:
2 + 2 = 4
Text in gray boxes
Describes Cautions or unique functionality of the product.

User Guide 6 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Introduction
Abbreviation
Definition
I2C
inter-integrated circuit
I2S
Inter-IC Sound
LED
light-emitting diode
LPO
low power oscillator
PC
personal computer
PDL
peripheral driver library
QSPI
Quad serial peripheral interface
SDHC
Secure Digital Host Controller
SDIO
Secure Digital Input Output
SDK
software development kit
SMIF
Serial Memory Interface
SPI
Serial Peripheral Interface
SRAM
static random-access memory
SWD
Serial Wire Debug
UART
universal asynchronous receiver transmitter
USB
Universal Serial Bus
WCO
watch crystal oscillator

User Guide 7 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
2
2.1 
•KIT_T2G-B-E_LITE board
Figure 1 Kit contents
Inspect the contents of the kit; if you find any part missing, go to
https://www.infineon.com/cms/en/product/microcontroller/32-bit-traveo-t2g-arm-cortex-
microcontroller/32-bit-traveo-t2g-arm-cortex-for-body/traveo-t2g-cyt2bl-series.
2.2 
The KIT_T2G-B-E_LITE has the following features:
•TRAVEO™ T2G-B-E MCU. See the device datasheet.
•KitProg3 on-board SWD programmer/debugger, USB-UART, and USB-I2C bridge functionality.
•A micro-B connector for USB device interface
•Selectable input supply voltages of 3.3 V and 5.0 V for the TRAVEO™ T2G-B-E MCU.
•Three user LEDs, two user buttons, and a reset button for the TRAVEO™ T2G-B-E MCU
•A potentiometer which can be used to simulate analog sensor output
•A mode button and a mode LED for KitProg3

User Guide 8 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
1
2
1
19
3456 7
8
9
10
11
12
13
14
15
16
18
25
2429 28 27 26 222120
23
17
Figure 2 KIT_T2G-B-E_LITE board top view
1. Shield2Go connectors (Not Mounted) (J7, J19)
2. MikroBUS connectors (J11, J12)
3. 32.768-kHz oscillator for WCO (Y1)
4. 16-MHz oscillator for ECO (Y2)
5. 8-pin Arduino header (J13)
6. Expansion header 1 (X1)
7. 6-pin Arduino header (J15)
8. DC Power Jack (J1)
9. Power LED (LED2)
10.KitProg3 USB Micro-B Connector (J2)
11.TRAVEO™ T2G microcontroller (U7)
12.MIPI10/20 DEBUG connector (J4)
13.VDDIO current measurement jumper (J21)
14.PSoC™5LP based KitProg3 (U4)
15.Mode switch (SW1)
16.KitProg3 Status LED (LED1)
17.VDD current measurement jumper (J20)
18.8-pin Arduino header (J14)
19.Potentiometer (VR5)
20.USER LED3 (LED5)
21.USER LED2 (LED4)

User Guide 9 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
22.USER LED1 (LED3)
23.Expansion Header 1 (X2)
24.10-pin Arduino header (J16)
25.CAN FD transceiver (U8)
26.CAN FD connector (J5)
27.USER2 button (SW3)
28.USER1 button (SW2)
29.RESET button (SW1)
KIT_T2G-B-E_LITE board pinout details
GND
P17_1
N.C.
N.C.
N.C.
N.C.
P0_2
P0_3
P2_0
P14_3
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
SPI_CS3
SPI_CS1
P7_6
VIN
3V3
P17_2
N.C.
N.C.
N.C.
N.C.
SPI_MOSI
SPI_CS0
SPI_CLK
SPI_MISO
N.C.
N.C.
N.C.
N.C.
XRES_L_MCU
ADC1_19
SPI_CS2
P7_7
N.C.
GND
UART_RX (D0)
UART_TX (D1)
P0_2 (D2)
P0_3 (D3)
P2_0 (D4)
P2_1 (D5)
P14_3 (D6)
P17_1 (D7)
Shield2Go
5V
AN1
AN2
SDA
SCL
GND
3V3
INT
PWM
RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
Shield2Go
5V
AN1
AN2
SDA
SCL
GND
3V3
INT
PWM
RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
mikro BUS
AN
RST
CS
SCK
MISO
MOSI
3V3
GND
PWM
INT
RX
TX
SCL
SDA
5V
GND
(VIN) VIN
(GND_2) GND
(GND_1) GND
(5V) 5V
(3V3) 3V3
(RST) XRES_L_MCU
(IOREF) 3V3
(P1) N.C.
(AD4/SDA) I2C_SDA
(AREF) 5V
(GND_3) GND
(D13) SPI_CLK
(D12) SPI_MISO
(D11) SPI_MOSI
(D10) SPI_CS3
(D9) P11_0
(AD5/SCL) I2C_SCL
(D8) P17_2
GND
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
P11_0
P11_2
ADC1_6
ADC1_8
N.C.
N.C.
UART_RX
N.C.
USER_SW1
USER_LED1
USER_LED3
N.C.
VIN
3V3
N.C.
N.C.
N.C.
N.C.
N.C.
POT_AOUT
P11_1
ADC1_22
ADC1_7
N.C.
N.C.
5V
P2_1
UART_TX
USER_SW2
USER_LED2
N.C.
N.C.
GND
POT_AOUT (A0)
ADC1_6 (A1)
ADC1_7 (A2)
ADC1_8 (A3)
ADC1_19 (A4)
ADC1_22 (A5)
Figure 3 KIT_T2G-B-E_LITE board pinout

User Guide 10 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
Table 3 KIT_T2G-B-E_LITE board pinout
Pin
Primary onboard function
Secondary onboard
function
Connection details
-B-E MCU pins
XRES
Hardware reset
–
P12[0]
CAN transmit CAN_TX
–
Connected to TxD of
CAN FD transceiver
TLE9251VSJ
P12[1]
CAN receive CAN_RX
–
Connected to RxD of
CAN FD transceiver
TLE9251VSJ
P6[0]
Potentiometer (POT) output
POT_AOUT
Arduino header (J15.1)
–
P13[0]
D12 –header compatible with Arduino
(J16.5)
Expansion header
(X1.20)
–
P13[1]
D11 –header compatible with Arduino
(J16.4)
Expansion header
(X1.14)
–
P13[2]
D13 –header compatible with Arduino
(J16.6)
Expansion header
(X1.18)
–
P13[6]
D10 –header compatible with Arduino
(J16.3)
Expansion header
(X1.33)
–
P11[0]
D9 –header compatible with Arduino
(J16.2)
Shield2Go Connector
(J7.12)
Expansion header
(X2.26)
–
P17[2]
D8 –header compatible with Arduino
(J16.1)
Shield2Go Connector
(J19.13)
Expansion header
(X1.4)
–
P14[0]
UART_RX
Shield2Go Connector
(J7.10, J19.10)
MikroBUS Connector
(J12.6)
This pin is connected to
the KitProg3 UART Tx
pin.
P14[1]
UART_TX
Pin D1 of connector
J4.2 compatible with
Arduino Shield2Go
Connector (J7.11,
J19.11)
MikroBUS Connector
(J12.5)
This pin is connected to
the KitProg3 UART Rx
pin.
Remove R132 and R142,
and install R136 to
connect to Pin D1 of
connector J4.2
compatible with
Arduino.
P0[2]
Pin D2 of connector J14.3 compatible
with Arduino
–
–
P0[3]
Pin D3 of connector J14.4 compatible
with Arduino
–
–

User Guide 11 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
Pin
Primary onboard function
Secondary onboard
function
Connection details
P2[0]
Pin D4 of connector J14.5 compatible
with Arduino
–
–
P2[1]
Pin D5 of connector J14.6 compatible
with Arduino
–
–
P14[3]
Pin D6 of connector J14.7 compatible
with Arduino
–
–
P17[1]
Pin D7 of connector J14.8 compatible
with Arduino
–
–
P12[2]
A1 –header compatible with Arduino
(J15.2)
–
–
P12[3]
A2 –header compatible with Arduino
(J15.3)
–
–
P12[4]
A3 –header compatible with Arduino
(J15.4)
–
–
P13[7]
A4 –header compatible with Arduino
(J15.5)
–
–
P14[2]
A5 –header compatible with Arduino
(J15.6)
–
–
P6[1]
I2C SDA - Common I2C SDA pin for
KitProg3 USB-I2C bridge
I2C SDA pin Arduino
header (J16.9)
–
P6[2]
I2C SCL - Common I2C SCL pin for
KitProg3 USB-I2C bridge
I2C SCL pin on Arduino
header (J16.10)
–
P5[0]
USER LED1 (LED1)
ExpansionConnector
(X2.8)
–
P5[1]
USER LED2 (LED2)
ExpansionConnector
(X2.7)
–
P5[2]
USER LED3 (LED3)
ExpansionConnector
(X2.6)
–
P5[3]
User button (USER BUTTON1)
Expansion Connector
(X2.10)
–
P17[0]
User button (USER BUTTON2)
Expansion Connector
(X2.9)
–
P21[0]
WCO IN (Y1)
–
32.768-kHz watch
crystal oscillator input
P21[1]
WCO OUT (Y1)
–
32.768-kHz watch
crystal oscillator output
P21[2]
ECO IN (Y2)
–
16-MHz external crystal
oscillator input
P21[3]
ECO OUT (Y2)
-
16-MHz external crystal
oscillator input
P23[4]
SWO_TDO
DEBUG MIPI 10/20
Connector (J4.6)
–

User Guide 12 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit details
Pin
Primary onboard function
Secondary onboard
function
Connection details
P23[5]
SWCLK_TCLK
DEBUG MIPI 10/20
Connector (J4.4)
–
P23[6]
SWDIO_TMS
DEBUG MIPI 10/20
Connector (J4.2)
–
P23[7]
SWDOE_TDI
DEBUG MIPI 10/20
Connector (J4.8)
–
P18[3]
TRACE_CLK
DEBUG MIPI 10/20
Connector (J4.12)
–
P18[4]
TRACE_DATA0
DEBUG MIPI 10/20
Connector (J4.14)
–
P18[5]
TRACE_DATA1
DEBUG MIPI 10/20
Connector (J4.16)
–
P18[6]
TRACE_DATA2
DEBUG MIPI 10/20
Connector (J4.18)
–
P18[7]
TRACE_DATA3
DEBUG MIPI 10/20
Connector (J4.20)
–

User Guide 13 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
3
3.1 
The TRAVEO™ T2G-B-E evaluation board is built around TRAVEO™ T2G-B-E MCU. For details of device features,
see the device datasheet.
I/O Subsystem
Peripheral Interconnect (MMIO, PPU)
IOSS GPIO
PCLK
7x SCB
I2C, SPI, UART
CPU Subsystem
System Interconnect (Multi Layer AHB, IPC, MPU/SMPU)
CRYPTO
AES, SHA, CRC,
TRNG, RSA,
ECC
Initiator/MMIO
High-Speed I/O Matrix, Smart I/O, Boundary Scan
1x SCB
I2C, SPI, UART
CYT2BL
MXS40-HT
ASIL-B
Digital DFT
Test
Analog DFT
System Resources
Power
Reset
Sleep Control
PWRSYS-HT
REF
POR
Reset Control
TestMode Entry
XRES
LVD
BOD
OVD
LDO
Clock
Clock Control
IMO WDT
CSV
1xPLL
ECO
2xILO
FLL
83x TCPWM
TIMER, CTR, QD, PWM
SWJ/MTB/CTI
MUL,NVIC, MPU
Arm Cortex
M0+
100 MHz
5x Smart I/O
8x CANFD
CAN-FDInterface
eFUSE
1024 bit
SWJ/ETM/ITM/CTI
Arm Cortex M4
160 MHz
FPU, NVIC, MPU
eCT Flash
4160 KB Code-flash +
128 KB Work-flash
FLASHController
8 KB $ 8 KB$
SRAM0
256 KB
SRAM Controller
ROM
32 KB
ROM Controller
12x LIN
LIN/UART
Prog.
Analog
SAR
ADC
(12-bit)
x3
SARMUX
64 ch
WCO
SRAM1
256 KB
SRAM Controller
M-DMA0
4 Channel
P-DMA1
44 Channel
P-DMA0
92 Channel
DeepSleep
Hibernate
Active/Sleep
LowePowerActive/Sleep
Power Modes
Up to148x GPIO_STD, 4x GPIO_ENH
EVTGEN
Event Generator
4x CXPI
CXPI Interface
RTC
Figure 4 -B-E MCU block diagram

User Guide 14 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
TRAVEOT2G
(Target Device)
User Button (x2)
WCO (32.768 KHz)
Loaded Pa rts No Load PartsInfineon Parts
ECO
(16 MHz)
CAN FD
User LEDs (x3)
Arduino Headers
Expansion Headers
Potentiometer
KitProg3
(PSoC5LP)
HW ID 0x0D
St atus LED Mode Switch
KitProg3 USB
(Micro-B)
Voltage
Monitoring
KitProg3
HW ID
Reset Button
20 /10 Pin JTAG/
SWD/ETM Header
I2C
SWD
KP_VBUS
VTARG_MON
P5LP_VDD
UART TX, RX
MikroBUS Headers
Shield2Go Header s
TRAVEOT2G
Body Entry
(Target Device)
Figure 5 Block diagram of KIT_T2G-B-E_LITE board
1
2
1
19
3456 7
8
9
10
11
12
13
14
15
16
18
25
2429 28 27 26 222120
23
17
Figure 6 KIT_T2G-B-E_LITE board top view

User Guide 15 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
The KIT_T2G-B-E_LITE board has the following peripherals:
Table 4 Peripheral details
Sl. No.
Peripheral
Description
1.
Shield2Go Connector
Option connector for Shield2Go Interface (DNI)
2.
MikroBUS Connector
Option connector for MikroBUS Interface (DNI)
3.
32.768 kHz crystal for WCO (Y1)
Oscillator for WCO clock.
4.
16 MHz crystal for ECO (Y2)
Oscillator for ECO clock.
5.
Digital I/O headers compatible
with Arduino Uno R3 (J13)
Bring out pins from TRAVEO™ T2G-B-E MCU to interface with
shields compatible with Arduino. Some of these pins are
multiplexed with onboard peripherals and are not connected
to TRAVEO™ T2G-B-E MCU by default. For detailed information
on how to rework the kit to access these pins, see 0.
6.
Expansion Headers (X1)
These headers provide connectivity to TRAVEO™ T2G-B-E MCU
GPIOs that are not connected to the other onboard functions.
7.
Analog-IN header compatible
with Arduino Uno R3 (J15)
Bring out pins from TRAVEO™ T2G-B-E MCU to interface with
shields compatible with Arduino. Some of these pins are
multiplexed with onboard peripherals and are not connected
to TRAVEO™ T2G-B-E MCU by default. For detailed information
on how to rework the kit to access these pins, see 0.
8.
External power supply VIN
connector (J1)
Connect to external 12 V/3 A DC power adapter.
9.
Power LED (LED2)
Power supply ON/OFF LED status indicator.
10.
KitProg3 USB connector (J2)
Connect to a PC to use the KitProg3 onboard programmer and
debugger and to provide power to the board.
11.
T2G-B-E microcontroller (U7)
TRAVEO™ T2G MCU device used on the kit.
12.
DEBUG MIPI 10/20 connector
(J4)
Connect to an Embedded Trace Macrocell (ETM)-compatible
programmer/debugger. This is not loaded by default.
13.
T2G-B-E VDDIO current
measurement jumper (J21)
J12 connects MCU VDDIO2 to T2G-B-E_VDD which is the
outcome of J10 (VCC_3V3 or VCC_5V0) power supply selection.
14.
KitProg3 (PSoC™5LP)
programmer and debugger
(CY8C5868LTI-LP039, U4)
The PSoC™ 5LP device (CY8C5868LTI-LP039) serving as
KitProg3, is a multi-functional system, which includes an SWD
programmer, debugger, USB-I2C bridge, and USB-UART
bridge. For more details, see the KitProg3 user guide.
15.
KitProg3 programming mode
selection button (SW1)
Use this button to switch between various modes of operation
of KitProg3. Note that this board supports only CMSIS-DAP
BULK mode. For more details, see the KitProg3 user guide.
This button function is reserved for future use.
16.
KitProg3 status LED (LED1)
Amber LED (LED1) indicates the status of KitProg3. For details
on the KitProg3 status, see the KitProg3 user guide.
17.
T2G-B-E VDD current
measurement jumper (J20)
J12 connects MCU VDDIO2 to T2G-B-E_VDD which is the
outcome of J10 (VCC_3V3 or VCC_5V0) power supply selection.
18.
Power header compatible with
Arduino Uno R3 (J14)
Powers the shields compatible with Arduino. It also has a
provision to power the kit through the VIN input.

User Guide 16 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
Sl. No.
Peripheral
Description
19.
Potentiometer (VR1)
10-kΩ potentiometer connected to TRAVEO™ T2G-B-E MCU pin
P6[0]. It can be used to simulate a sensor output to TRAVEO™
T2G-B-E MCU.
20.
User LEDs (LED5)
The user LEDs can operate at the entire operating voltage
range of the TRAVEO™ T2G-B-E MCU. The LEDs are active LOW,
so the pins must be driven to the ground to turn ON the LEDs.
21.
User LEDs (LED4)
The user LEDs can operate at the entire operating voltage
range of the TRAVEO™ T2G-B-E MCU. The LEDs are active LOW,
so the pins must be driven to the ground to turn ON the LEDs.
22.
User LEDs (LED3)
The user LEDs can operate at the entire operating voltage
range of the TRAVEO™ T2G-B-E MCU. The LEDs are active LOW,
so the pins must be driven to the ground to turn ON the LEDs.
23.
Expansion Headers (X2)
These headers provide connectivity to TRAVEO™ T2G-B-E MCU
GPIOs that are not connected to the other onboard functions.
24.
Digital I/O headers compatible
with Arduino Uno R3 (J16)
Bring out pins from TRAVEO™ T2G-B-E MCU to interface with
shields compatible with Arduino. Some of these pins are
multiplexed with onboard peripherals and are not connected
to TRAVEO™ T2G-B-E MCU by default. For detailed information
on how to rework the kit to access these pins, see 0.
25.
CAN FD transceiver (U8)
CAN FD transceiver.
26.
CAN FD interface connector (J5)
Connector to connect the kit to the CAN / CAN FD network
27.
User buttons (SW4)
Provide input to TRAVEO™ T2G-B-E MCU. Note that by default
the button connects the TRAVEO™ T2G-B-E MCU pin to the
ground when pressed, so you need to configure the TRAVEO™
T2G-B-E MCU pin as a digital input with resistive pull-up for
detecting the button press.
28.
User buttons (SW3)
Provide input to TRAVEO™ T2G-B-E MCU. Note that by default
the button connects the TRAVEO™ T2G-B-E MCU pin to the
ground when pressed, so you need to configure the TRAVEO™
T2G-B-E MCU pin as a digital input with resistive pull-up for
detecting the button press.
29.
T2G-B-E reset button (SW2)
Resets TRAVEO™ T2G-B-E MCU. It connects the TRAVEO™ T2G-
B-E MCU reset (XRES) pin to the ground.
See 4.4 Layouts for details on various hardware blocks.

User Guide 17 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
3.2 
The TRAVEO™ T2G-B-E evaluation board can be programmed and debugged using the onboard KitProg3.
KitProg3 is an onboard programmer/debugger with USB-UART, USB-I2C, and USB-SPI Bridge (not supported on
this board) functionality. KitProg3 supports CMSIS-DAP only and does not support mass storage. A PSoC™5LP
device is used to implement the KitProg3 functionality. For more details on the KitProg3 functionality, see the
KitProg3 user guide.
3.2.1 

1. Connect the board to the PC using the provided USB cable through the KitProg3 USB connector, as shown in
Figure 7. It enumerates as a USB Composite Device if you are connecting it to your PC for the first time.
2. KitProg3 on this kit supports CMSIS-DAP Bulk mode (default) and CMSIS-DAP Bulk with two UARTs. The
status LED (amber) is always ON in the CMSIS-DAP Bulk mode. If you do not see the desired LED status, see
the KitProg3 user guide for details on the KitProg3 status and troubleshooting instructions.
Note: The programming can be done in either of the KitProg3 programming modes but it is
recommended to program the kit in CMSIS-DAP Bulk mode.
Figure 7 Connect USB cable to USB connector on the board
3.
a) Open the IAR EWARM debugger and import the desired code example (application) from the SDL into a
new workspace. For example, to open the IAR tool EWARM workspace.

User Guide 18 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
Figure 8 Open Sample Driver Library
b) Select Make icon and execute. If compiling succeeds, then select download and debug and execute.
Confirm the debug execution.
Figure 9 Open Sample Driver Library using IAR EWARM

User Guide 19 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Kit operation
3.2.2 
KitProg3 on the TRAVEO™ T2G-B-E evaluation board can act as a USB-UART bridge.
The UART Rx and Tx pins of KitProg3 are connected to the TRAVEO™ T2G-B-E MCU UART pins as follows:
KitProg3
KP_UART_1_CTS
P13[3]
P13[2]
USB
RX
TX
KP_UART_1_RTS
TRAVEOTM T2G-B-E MCU
P13[0]KP_UART_1_TX
KP_UART_1_RX P13[1]
CTS
RTS
Figure 10 UART connection between KitProg3 and -B-E MCU

User Guide 20 002-37239 Rev. **
2023-07-20
KIT_T2G-B-E_LITE user guide
Hardware
4
4.1 
4.1.1 
The correspondence between the LEDs on the board and the CYT2BL5xx device pins and the port pins are
shown in Table 5.
Table 5 USER LEDs
USER LED
Part number
CYT2BL5xx
Pin
Pin
USER LED 1
LED3
14
P5.0
USER LED 2
LED4
15
P5.1
USER LED 3
LED5
16
P5.2
4.1.2 
The correspondence between the switches and the CYT4BF8xx device pins and the port pins are shown in Table
6.
Table 6 USER switches
USER switch
Part number
CYT2BL5xx
Pin
Pin
USER SW 1
SW3
17
P5.3
USER SW 2
SW4
64
P17.0
4.1.3 
The correspondence between the RESET switch and the CYT2BL5xx device pin and the port pin are shown in
Table 7.
Table 7 RESET switch
USER switch
Part number
CYT2BL5xx
Pin
Pin
RESET SW
SW2
85
XRES
4.1.4 
The mode switch will change the mode of operation of the KitProg3 device. While communicating with the
TRAVEO™T2G device, make sure that the KitProg3 device should be in CMSIS DAP mode (LED1
is solid ON).
The correspondence between the MODE SW and the PSoC™5LP pin number is given in 0.