Infineon AIROC CYW20829 User manual

Quick start guide
AIROC™CYW20829 Bluetooth®LE SoC Evaluation Kit
CYW920829M2EVK-02
www.infineon.com/CYW920829M2EVK-02
Kit contents
1. CYW20829 Evaluation Board (CYW9BTM2BASE3+CYW920829M2IPA2)
2. USB Type-A to Micro-B cable
3. Six jumper wires (five inches each)
4. Quick start guide (this document)

Quick start guide
Before you start
1. Ensure that you have the following:
• PC with USB 2.0 port
• UART terminal soware such as
Tera Term or Minicom
• Download and install the AIROC™ Bluetooth®
Connect app from Play Store or iOS App Store.
2. Visit the kit website to download and
install the required soware.
3. Ensure the following jumper settings to select 3.3 V:
5. Wait for the driver installation to complete.
6. Open the UART terminal soware and set the
USB-UART COM port terminal setting by referring
to COM port setup image.
4. Connect the KitProg3 USB connector (J5)
to your PC.
USB cable connected to the
KitProg3 USB connector
Jumper
J9
J10
J12
1 – 3
1 – 3
1 – 2
Position
Run the AIROC™Bluetooth®Connect application
1. Turn ON Bluetooth® on your Android or iOS device.
2. Launch the AIROC™Bluetooth®Connect app.
3. Press the reset switch on the CYW920829M2EVK-02
board to start sending advertisements and observe
the “Advertisement started” message on the serial
terminal and confirm USER LED2 blinking.
4. Swipe down on the AIROC™Bluetooth®Connect app
home screen to start scanning for LE Peripheral
devices.
5. Your device (“Find Me Target”) appears on the
home screen. Tap Connect to establish a Bluetooth®
LE connection with the device.
6. The USER LED2 changes from blinking state to
always ON state aer establishing a successful
connection with the device.
7. Select ‘Find Me Profile’ and select an Alert level.
The USER LED1 state is linked to the type of
alert sent.
• No alert: USER LED1 OFF
• Mild alert: USER LED1 blinking
• High alert: USER LED1 ON
AIROC™Bluetooth®Connect app – Android
AIROC™Bluetooth®Connect app – iOS
USB-UART COM port setup

Quick start guide
1. Power LED (LED1)
2. KitProg3 USB Micro-B connector (J5)
3. KitProg3 programming mode selection button (SW3)
4. KitProg3 (PSoC™ 5LP) programmer
and debugger (CY8C5868LTI - LP039, U5)
5. VBAT voltage selection jumper (J9)
6. VIO_BASE voltage selection jumper (J10)
7. VDDPA voltage selection jumper (J12)
8. Analog mic (U13)**
9. Power header compatible with
Arduino Uno R3 (J1)
10. Reset button (SW1)
11. 10-pin MCU PROG/DEBUG header (J11)
12. Analog header compatible with
Arduino (J2)
13. User Button 1 (SW2)
14. Digital mic (U11)**
15. User Button 2 (SW4)
16. User LED 1 (LED3)
17. User LED 2 (LED4)
18. M.2 stand-off (MT1)
19. AIROC™ CYW20829 Bluetooth® and
Bluetooth® LE system on chip
20. M.2 E-key interface connector (J16)
21. RGB LED (LED5)
22. Thermistor (TH1)
23. Thermistor enable header (J14)
24. Peripheral enable header (J13)
25. VDDIO current measurement header (J17)
26. Six-axis IMU (U12)
27. QSPI flash memory (U14)*
28. Digital I/O headers compatible
with Arduino Uno R3 (J3, J4)
29. Extended GPIO header (J18)
30. KitProg3 status LED (LED2)
AIROC™CYW20829 Evaluation Board details
1
2
3
4
5
6
7
89 10 11 12 13 14
15
16
17
18
19
20
21
22
23
24
252627282930
*Footprint only, not populated on the board
**Component is located at the bottom side of the board

See the kit guide available at www.infineon.com/CYW920829M2EVK-02 for details.
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2023 Infineon Technologies AG.
All Rights Reserved.
Please note! Additional information
For further information on technologies, our products, the
application of our products, delivery terms and conditions
and/or prices, please contact your nearest Infineon Technologies
office (www.infineon.com).
Warnings
Due to technical requirements, our products may contain
dangerous substances. For information on the types in question,
please contact your nearest Infineon Technologies office.
Except as otherwise explicitly approved by us in a written
document signed by authorized representatives of Infineon
Technologies, our products may not be used in any life-
endangering applications, including but not limited to medical,
nuclear, military, life-critical or any other applications where a
failure of the product or any consequences of the use thereof
can result in personal injury.
www.infineon.com
Document Number: 002-37204 Rev. *A
Date: 08/ 2023
Quick start guide
NC
VIO/IOREF
RST/RESET
V3.3/V3.3
V5.0/V5.0
GND/GND
GND/GND
NC/VIN
AIROC™CYW20829 Evaluation Board pinout details
This Document is for information purposes only and any
information given herein shall in no event be regarded as a
warranty, guarantee or description of any functionality,
conditions and/or quality of our products or any suitability
for a particular purpose. With regard to the technical
specifications of our products, we kindly ask you to refer
to the relevant product data sheets provided by us.
Our customers and their technical departments are
required to evaluate the suitability of our products
for the intended application.
We reserve the right to change this document and/or
the information given herein at any time.
P4.0/SCL
P4.1/SDA
NC
GND/GND
P1.1/D13
P1.3/D12
P1.2/D11
P1.0/D10
P1.6/D9
P1.5/D8
GND
NC
P3.1
P3.0
P0.4
P0.3
P0.2
P0.5
P5.2
P1.1
P0.1/D7
P0.0/D6
P1.2/D5
P1.3/D4
P1.0/D3
P1.4/D2
P3.3/D1
P3.2/D0
P3.4/A0
P3.5/A1
P3.6/A2
P3.7/A3
P0.0/A4
P0.1/A5
P5.0/A6
P5.1/A7
Legend I/Os compatible with Arduino Uno R3 CYW20829 I/Os