Infineon XMC Series User guide

Microcontrollers
XMC4000/1000
Microcontroller Series
for Industrial Applications
Application Guide
V1.0 2015-01
Introduction to Digital Power
Conversion

Edition 2015-01
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2015 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all
warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual
property rights of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the
failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life
support devices or systems are intended to be implanted in the human body or to support and/or maintain and
sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other
persons may be endangered.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Revision History
Revision History
Page or Item
Subjects (major changes since previous revision)
V1.0, 2015-01
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolMOS™, CoolSET™,
CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™,
EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™,
IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™, PRIMARION™,
PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™, ReverSave™, SatRIC™,
SIEGET™, SINDRION™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, TEMPFET™, thinQ!™,
TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™,
PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by
AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum.
COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.).
EPCOS™ of Epcos AG. FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay
Consortium. HYPERTERMINAL™ of Hilgraeve Incorporated. IEC™ of Commission Electrotechnique
Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL
ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim
Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. Mifare™ of
NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA
MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc.,
OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™
Red Hat, Inc. RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of
Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited.
TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc.
TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™,
PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated.
VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited.
Last Trademarks Update 2011-02-24

Introduction to Digital Power Conversion
XMC4000/1000 Family
Table of Contents
Application Guide 4 V1.0, 2015-01
Table of Contents
1About this document .........................................................................................................................6
1.1 Scope and Purpose..............................................................................................................................6
1.2 Intendend Audience .............................................................................................................................6
2Comparison of Power Conversion Methods ...................................................................................7
2.1 What is Power Conversion...................................................................................................................7
2.2 Why Power Conversion........................................................................................................................7
2.3 Methods of Power Conversion.............................................................................................................7
2.3.1 Linear Mode Power Conversion.....................................................................................................7
2.3.2 Switch Mode Power Conversion....................................................................................................9
2.3.2.1 Analog Switch Mode Controllers.............................................................................................11
2.3.2.2 Digital Switch Mode Controllers..............................................................................................11
2.3.2.3 ASIC controller versus MCU / DSP / DSC controllers............................................................12
2.4 Infineon XMC-families for Switch Mode Power Control .....................................................................13
2.4.1 Power Conversion Oriented Peripheral Features........................................................................14
2.4.1.1 Sensing...................................................................................................................................14
2.4.1.2 Stability and Software .............................................................................................................14
2.4.1.3 Modulation ..............................................................................................................................14
2.4.1.4 PWM Generation ....................................................................................................................15
3Converter Topologies......................................................................................................................16
3.1 Buck ...................................................................................................................................................17
3.2 Boost ..................................................................................................................................................18
3.3 PFC ....................................................................................................................................................19
3.4 Phase-Shift Full-Bridge (PSFB) .........................................................................................................21
3.5 LLC (Inductor-Inductor-Capacitor) .....................................................................................................22
3.6 Generic Digital Power Converter........................................................................................................23
4PWM Generation...............................................................................................................................24
4.1 Single Channel...................................................................................................................................24
4.2 Single Channel with Complementary Outputs ...................................................................................24
4.3 Dual Channel with Complementary Outputs with Dead-Time, using CCU8......................................25
4.4 Dual Channel with Complementary Outputs with Dead-Time, using CCU4......................................25
4.5 ON/OFF Control.................................................................................................................................27
4.6 Fixed ON-Time (FOT) ........................................................................................................................27
4.7 Fixed ON-Time with Frequency Limit Control....................................................................................28
4.8 Fixed Off-Time (FOFFT) ....................................................................................................................31
4.9 Phase Shift Control ............................................................................................................................32
4.10 Fixed Phase-Shift...............................................................................................................................32
4.10.1 Center Aligned Mode ...................................................................................................................32
4.10.2 Edge Aligned Mode......................................................................................................................33
4.10.3 Interleave .....................................................................................................................................34
4.11 Variable Phase-Shift ..........................................................................................................................35
4.11.1 Power Conversion Control Example............................................................................................37
4.11.2 Zero-Voltage Switching (ZVS) Control.........................................................................................38
4.12 Adding High Resolution Channel (HRC) –HRPWM..........................................................................39
4.12.1 PWM Dead-Time Compensation .................................................................................................40
4.13 Half-Bridge LLC Control using ½ CCU4.............................................................................................41
4.14 Half-Bridge LLC Control - Synchronous Rectification using CCU4 ...................................................42
4.15 Full-Bridge LLC Control Using HRC –Synchronous Rectification.....................................................43
4.16 Full-Bridge LLC Control –Synchronous Rectification Using HRC.....................................................44
5Sensing .............................................................................................................................................46
5.1 Analog Signal Sensing.......................................................................................................................46
5.1.1 Level Crossing Detection, Fast Compare mode..........................................................................46
5.1.2 PWM with Fast Compare mode Hysteretic Switching .................................................................47
5.1.3 Peak Control Using Fast Compare mode....................................................................................48
5.1.4 ZCD Control Using Fast Compare mode.....................................................................................49

Introduction to Digital Power Conversion
XMC4000/1000 Family
Table of Contents
Application Guide 5 V1.0, 2015-01
5.2 Over Voltage and Over Current Protection (OVP / OCP)..................................................................50
6Modulation ........................................................................................................................................51
6.1 Voltage Control (VC)..........................................................................................................................52
6.1.1 Timing Scheme............................................................................................................................53
6.2 Current Control...................................................................................................................................55
6.2.1 Average Current Control (ACC)...................................................................................................55
6.2.2 Average Current Control, Edge-Aligned Scheme........................................................................56
6.2.3 Discontinuous to Continuous Current Recovery by Timer-Load .................................................58
6.2.4 ACC Center Aligned Scheme ......................................................................................................59
6.3 Peak Current Control (PCC) ..............................................................................................................60
6.3.1 PCC Timing Scheme....................................................................................................................62
6.4 Blanking, Filtering and Clamping .......................................................................................................63
6.5 Slope Compensation..........................................................................................................................64
6.5.1 A Necessity in Fixed Frequency PCC..........................................................................................64
6.5.2 Fast Average Current Mode PCC................................................................................................65
6.5.3 VIN independent Average Current mode......................................................................................66
6.5.4 Slope Compensation Conditions –PCC......................................................................................67
6.5.5 Slope Compensation Conditions: PCC ‘Stable Area’ examples ..................................................70
6.5.6 Without Slope Compensation, Fixed-ON-Time (FOT) ZCD Control............................................71
6.5.7 Without Slope Compensation, Fixed-OFF-Time (FOFFT) PCC..................................................71
6.6 CCM, CRM (CrCM) and DCM............................................................................................................72
6.7 CRM: PFC using Fixed-On-Time (FOT).............................................................................................74
6.8 CCM / (DCM): PFC using Fixed-Off-Time (FOFFT) ..........................................................................75
6.9 CCM: PFC example using Average Current Mode Control ...............................................................76
7Control Loops...................................................................................................................................77
7.1 Using CSG (HRPWM) with an Internal Comparator and Slope Generator........................................77
7.2 Using embedded ACMP and external Slope Compensation Ramp ..................................................78
7.3 Using FADC Compare Mode; Slope Compensation Add-On ............................................................81
7.4 Open Loop Gain Stabilization (Frequency Compensation)................................................................83
7.4.1 Open Loop Gain Voltage Mode ...................................................................................................84
7.4.2 Open Loop Gain Bode Plot, Voltage Mode Stabilization .............................................................85
7.4.3 Open Loop Gain Current Mode w/ Slope Compensation ............................................................86
7.4.4 Open Loop Gain Bode Plot, Current Mode Stabilization .............................................................87
8Application Software .......................................................................................................................88
8.1 Advanced Algorithms / User software IP for Power Conversion........................................................88
8.2 Multi-stage, multi-functional, multi-tasking control by a single controller...........................................88
8.3 Safety .................................................................................................................................................89
8.4 Communication capabilities ...............................................................................................................89
8.5 Data logging / Firmware updates.......................................................................................................89
8.6 Human Machine Interface..................................................................................................................89
8.7 Digital Switch Mode Control by New Feed-Forward Techniques ......................................................90
8.8 Non-linear Slope Compensation........................................................................................................90

Introduction to Digital Power Conversion
XMC4000/1000 Family
About this document
Application Guide 6 V1.0, 2015-01
1 About this document
1.1 Scope and Purpose
This document aims to stimulate and challenge accepted solutions in the field of power applications
with digital control, by revisiting the basics of electric energy transfer and creating a summarized
picture of what can be achieved today with a weighted mix of embedded dedicated peripherals and
computing power.
1.2 Intendend Audience
The information is intended for persons in charge or executive position, with a diverse background in
the subject –as well as to people with deeply rooted experience in the field, such as power supply
designers, for which we want to show the possibilities XMC families can offer.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 7 V1.0, 2015-01
2 Comparison of Power Conversion Methods
2.1 What is Power Conversion
Power conversion is the conversion of electric energy from one form to another. As long as it does not
concern electro-mechanic equivalent energy that consumes energy (e.g. motors) or produces energy
(e.g. generators), then it is about pure power transfer, in any form, from the following categories:
Table 1 Power conversion categories
Category
Type
General Purpose
DC / DC
DC-to-DC converter
Regulator / Stabilizer / Voltage Adapter
AC / DC
AC-to-DC converter
Rectifier / Mains Power Supply Unit (PSU)
DC / AC
AC-to-DC converter
Inverter
AC / AC
AC-to-AC converter
Transformer / Variable frequency Converter
2.2 Why Power Conversion
According to the global environmental context, each case of electric energy transfer between an
energy source and an energy consuming unit, should consume as little energy as possible to perform
the task by optimal adaption. This is generally unachievable without some form of power conversion.
2.3 Methods of Power Conversion
There are two significantly different ways to convert a DC supply voltage to another DC voltage:
Linear Power Conversion
Switch Mode Power Conversion
When Switch Mode is chosen (e.g. for High Power) the next choice is between:
Analog (discrete) control
Digital (ASIC/MCU/DSP) control
2.3.1 Linear Mode Power Conversion
A Linear DC/DC Converter output/input voltage ratio is < 1 and the output/input current ratio is < 1, so
there is always a significant power loss.
Linear voltage regulators meet such demands as ‘Easy-to-Use’, Accuracy, Low Cost and EMC. They
are therefore the “best-choice” in low power / low current DC-converters.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 8 V1.0, 2015-01
Figure 1 Linear DC/DC Conversion
Passive Linear Conversion
Passive conversion means that there are no control components involved in the process that are
capable of changing the conversion properties in any way; i.e. the steady state input-to-output transfer
function is not adjustable in runtime. The consequence of this is Load dependent output voltage.
Active Linear Conversion
By “active” conversion we mean that there are components involved that are capable of influencing
the conversion activity; i.e. there is at least one semiconductor capable of controlling the conversion
by at least one additional input signal. This might be to stabilize the output to a reference level for
example.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 9 V1.0, 2015-01
2.3.2 Switch Mode Power Conversion
A Switch Mode DC/DC Converter output/input voltage ratio can be any value, including a negative
value. That property is not covered by any Linear Voltage Converter, so most power conversion use-
cases can be solved by Switch Mode, especially in the area of high power, where efficiency and form-
factor are vital.
Figure 2 Switch Mode DC/DC Conversion
Switch mode conversion is always an “active” conversion, in the sense there has to be active, working
semiconductors in the input-to-output transfer path. The presence of at least one winded component,
such as an inductor, is also essential.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 10 V1.0, 2015-01
Switch Mode Power Conversion Principle –Compared to Linear Mode
In switch mode voltage conversion, portions of energy, divided by switching in time lengths (T1or T2),
are transferred from a voltage source to an inductor (L) current as magnetic energy, cyclic in periods
(T). During the rest of each period (T), the energy is moved into a capacitor (C), for the output voltage.
This principle is true for any DC/DC converter topology.
Interesting similarities with linear conversion can be seen in the output/input voltage ratios, when
replacing ‘R’ with ‘T’. This comparison is true as long as the magnetic energy of the inductor is never
emptied before the end of each period (T); i.e. Continuous Conduction Mode (CCM) is assumed.
Figure 3 Power Conversion Principles and Similarities - Demo Model
Power Loss Comparison
The voltage drop (V1–V2) in linear mode is maintained by a resistor (R) and constant current, causing
active power loss.
The voltage (V1–V2) in switch mode is reactive by self-inductance (L) during rising or falling current in
the switch time intervals (T1or T2) respectively, resulting (ideally) in no power loss.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 11 V1.0, 2015-01
2.3.2.1 Analog Switch Mode Controllers
Traditional Analog Controllers have a significant BOM (Bill of Materials) list of OpAmps, comparators,
filters, and so on. They cover just a limited range of topologies and do not adapt autonomously to
condition changes in run-time. Form factor can be poor and reusability is limited, but they are fast and
well known.
Table 2 Properties of Analog Controllers
Positive properties
Negative properties
Fast
Do not adapt to new conditions during run-time
Well known
Sensitivity of parasitic effects and ageing
Simple IPs
Limited range of topologies
Standard discreet components
Narrow input / load range with efficiency
2.3.2.2 Digital Switch Mode Controllers
Digital controllers are flexible, with a wide load / input range, and sophisticated reactions to condition
changes during run-time through multi-control loops. They are reconfigurable by software and can
connect to a network / HMI. A smart system can predict ageing or process variations, enabling
scalability and portability of IPs.
Digital Controllers –Positive properties
Cost is higher and complexity is higher too, but there are many positive properties:
Highest efficiency over wide load and input range
Sophisticated start-up algorithms
Overload condition reactions
Auto-switch between power modes (CCMCRMDCMBurst)
Programmable / configurable by software
Multiple control loops are possible
Correct real-time performance
Prediction of system behavior
Reduction of parasitic effects
Scalable for wider ranges
IPs are easily portable: lowhigh end
Fast time to market
Sophisticated reactions to events
Communication and HMI feature

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 12 V1.0, 2015-01
2.3.2.3 ASIC controller versus MCU / DSP / DSC controllers
Here we outline some of the guiding properties to be considered, for the type of controller to choose
when selecting for High-end versus Low-end.
ASIC
ASIC controllers offer gate drivers and fixed optimized solutions at the lowest possible cost. They are
easy to use and they fit Low-end switch mode converters very well.
However, on the downside, they only handle known changes in load and input conditions during run-
time, and reusability is limited because they are a customized solution.
Positive properties:
Custom design for known conditions
Fixed and optimized settings
Lowest possible cost
Easy to use
Embedded gate drivers
Form factor
MCU / DSP / DSC
An MCU, DSP or DSC controller brings a platform approach, a smart system with high computation
capability, and embedded power conversion orientated peripherals.
Condition changes are handled in run-time, ensuring the highest efficiency and correct real-time
performance. These features mean that the MCU, DSP or DSC solution is particularly suited to High-
end power converters.
Positive properties:
Platform approach (Reuse, Extend)
When highest efficiency is required
Mixed power mode capability
Variable load / inputs
Programmable dwith software IP
Flexible communication

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 13 V1.0, 2015-01
2.4 Infineon XMC-families for Switch Mode Power Control
The Infineon XMC power conversion oriented devices offer flexible 3-level control architectures, for
sense-compute-modulate-and-drive of any power converter topology.
Advanced analog and digital peripherals interact on events in real-time via a hardware matrix,
supported by DMA, Software, DSP (Digital Signal Processing) or over a network.
Figure 4 The Power Conversion Oriented XMC Devices 3-Level Architecture Control Loop
The XMC series for power control meets the performance challenges and demands of today’s
embedded control applications. The high performance, real-time capability is achieved with an ARM-
Cortex architecture, with or without DSP, and a Floating Point Unit (FPU).

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 14 V1.0, 2015-01
2.4.1 Power Conversion Oriented Peripheral Features
Here we highlight features of the XMC-family embedded peripherals that are essential for the
significant tasks required in power conversion control loops.
2.4.1.1 Sensing
Analog values are monitored, or detected upon crossing level limits, via Versatile Analog-to-Digital
Converter (VADC) channels (featuring fast compare mode), or by Analog Comparator (ACMP/CSG).
These units are interconnected with events via hardware action providers, or softwre routines via
interrupts.
The functionality of the ADCs includes:
Automatic scheduling of complex conversion sequences with priority for time-critical conversions
Synchronous sampling of up to 4 signals / Independent result registers, selectable for 8/10/12 bits
Sampling rates up to 2MHz / Flexible data rate reduction / FIR/IIR filter with selectable coefficients
Adjustable conversion speed and sampling timing
4 independent converters with up to 8 inputs w/ channel wise selectable reference voltage source
2.4.1.2 Stability and Software
An important property of conversion control loops is the frequency response of the duty-cycle-to-
output-voltage transfer function. Stabilization is provided via softwre actions in the open loop gain
paths, using DSP operations on discrete time variables, maintained by sampling at rates triggered by
a CCU (Capture and Compare Unit).
2.4.1.3 Modulation
The steady state duty-cycle-to-output-voltage transfer function is controlled by sense-modulate-drive
algorithms in hardware, with some optional add-on attributes, including (but not limited to):
Fixed-Frequency (FF)
Fixed-On-Time (FOT)
Fixed-Off-Time (FOFFT)
Conduction Mode Switching
Comparator & Slope Generation (CSG)
Blanking
Clamping
Filtering
XMC modulation modes
Voltage Mode Control (VC)
Average Current Mode Control (ACC)
Peak Current Mode Control (PCC)
Valley Current Mode Control (VCC)
Zero Crossing Detection Mode (ZCD)
The XMC peripherals handle modulation dynamically, with mode-switch on changed conditions in run-
time (on load variation for example). A set of resources can be exchanged “on-the-fly” by a Mode-Bit.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Comparison of Power Conversion Methods
Application Guide 15 V1.0, 2015-01
2.4.1.4 PWM Generation
The XMC CAPCOM Units (CCU4 or CCU8) timer slices can be regarded as “timer-cells” that can
cooperate and fit together like “puzzle pieces” to form matrices of sophisticated and compound timing
functions. These can interact for certain function request events and event profile conditions.
Theoretically, any on-chip module can be considered to act on a slice via one of (up to 3) inputs. A
flexible library of modular timing control applications (PWM “Apps”) can be created and then be
reused across projects.
The XMC single and multi-channel PWM drive capabilities include:
Global Synchronization
−to ensure a fully synchronized start with any combination of CAPCOM units
PWM
−by Symmetric / Asymmetric Modulation (Edge-Aligned or Center-Aligned)
−with Active / Passive Output Level Control / Trap Handling Protocol in hardware
−with Dithering (4 bits)
−by Status Events (by Compare or Period-Control)
−by external Set/Clear (by various conditional Start/Stop functions, which can be combined with
Status Events)
−by Matrix Interactions (on specific function request events and event profile conditions)
Examples
Peak, Valley or Hysteretic On-Off PWM
Fixed-On-TIme (FOT) PWM
Fixed-Off-TIme (FOFFT) PWM
Phase-Shift / Fixed Phase-Shift (Interleave) PWM
Half Bridge (HB) control with optional Synchronous-Rectification (SR)
Full Bridge (FB) control (w/ SR)
HB / FB Drive of LLC Resonance Converters
HRPWM Attributes
High Resolution Control (HRC) Insertion –down to 150 ps accuracy:
- HRC can handle switch frequencies up to 5 MHz with 10 bit resolution PWM
- Highly Accurate Low-Load Scenario Control
- Converter Efficiency Improvement: Each HRC can operate with two set of resources
Dead Time Insertion, with “On-the-Fly” optimization during run-time.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Converter Topologies
Application Guide 16 V1.0, 2015-01
3 Converter Topologies
The fundamental power converter topologies that we focus on in this document are:
Buck (“Step-Down”) (Section 3.1)
−Conventional
−Interleaved
−Synchronous
−Inverted
Boost (“Step-Up”) (Section 3.2)
−Conventional
−Interleaved
−Synchronous
−Inverted (Buck-Boost)
PFC (”Power-Factor-Correction” (Section 3.3)
−Conventional Boost PFC
−Interleaved Boost PFC
−Bridgeless Boost PFC
−Totem-Pole Bridgeless PFC
PSFB (“Phase-Shift-Full-Bridge”) (Section 3.4)
−(Principle Scheme)
LLC (”L-L-C-resonant”) (Section 3.5)
−(Principle Scheme)
The Generic Digital Power Converter (Section 3.6)

Introduction to Digital Power Conversion
XMC4000/1000 Family
Converter Topologies
Application Guide 17 V1.0, 2015-01
3.1 Buck
A Buck converter can only generate lower output average voltage (VOUT) than the input voltage (VIN),
and is therefore also referred to as a “Step-Down” converter.
The DC/DC conversion is non-isolating, in the sense that there is a common ground between input
and output. Some improved versions exist:
Figure 5 Buck
Interleaved Buck Converter
When reduced ripple and smaller components are required, especially in high-voltage applications,
then a realistic approach is to interleave the output currents from a multiphase Buck converter stage.
For example a 2-phase Buck converter controlled by fixed 180ophase-shifted PWM from an XMC
CCU4/8
Synchronous Buck Converter
When reduced power conversion loss is required, the rectifying diode D may be replaced by an active
switch that can offer a lower voltage drop. In such a solution the rectification will be synchronously
invoked by a signal that is complementary to the control signal, from a CC8 timer or CC4 timer pair.
Inverted Buck Converter
When a simplified current measurement is required, then an Inverted Buck controller is an alternative,
assuming common ground between input and output voltage is not necessary. By sensing the voltage
over a resistor (R) to ground, the inductor current (IL) can be monitored by a VADC or ACMP.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Converter Topologies
Application Guide 18 V1.0, 2015-01
3.2 Boost
A Boost converter is non-isolating and can only generate a higher output average voltage than the
input supply voltage. It is therefore called a “Step-Up” converter.
There is one exception to note however. The Inverted Buck-Boost converter theoretically generates
an output voltage from 0 to minus infinity.
Figure 6 Boost
Interleaved Boost Converter
Similar to the Buck converter, i.e. the ripple will be reduced and smaller components can be used, by
having interleaved output currents from a multiphase Boost converter stage –here by a 2-phase
Boost converter that is controlled by fixed 180ophase-shifted PWM from an XMC CCU4/-8.
Synchronous Boost Converter
A synchronous Boost works similar to a synchronous Buck –however, this variant of improvement is
not often used, since reduced power conversion loss by replacing the rectifying diode D by an active
switch is not very significant in the high voltage range –where this topology more frequently appears.

Introduction to Digital Power Conversion
XMC4000/1000 Family
Converter Topologies
Application Guide 19 V1.0, 2015-01
3.3 PFC
Abstract
The Power Factor (PF) is defined as the transfer ratio of real power [Watt] to apparent power [VA]:
PF = Real Power / Apparent Power [Watt / VA]
The Power-Factor-Correction (PFC) purpose is (according to the environmental context) to achieve:
Real Power = Apparent Power
i.e.:
PF = 1
PFC Rectifier
A PFC rectifier accomplishes “PF = 1” by phase correct rectification of the mains AC voltage –so that
the current conduction angle becomes fully 180oin both half periods –phase correct to the mains AC
voltage –i.e. without any parasitic or reactive signal components reflected back into the mains lines:
See Figure 7.
In principle, the mains is rectified into a sinusoidal half-wave rippling DC voltage. In turn it is converted
to a ripple-free DC output voltage by a Boost PFC –e.g. by Fixed-On-Time inductor current (IL) mode
control. (Each Off-Time interval lasts till the current (IL) falls back to Zero-Crossing-Detection, ZCD.)
Since all tOn pulses are fixed, the IL(PEAK) and IL(AVERAGE) envelopes will follow the |VAC(t)| in proportion.
Figure 7 Boost Power-Factor-Correction (PFC) –E.g. in Fixed On-Time Current Mode Control

Introduction to Digital Power Conversion
XMC4000/1000 Family
Converter Topologies
Application Guide 20 V1.0, 2015-01
PFC Variants
There are different types of PFC circuits, which mix a balance of complexity versus performance.
Here we show just some of the basic topologies. These can be mixed into more sophisticated, multi-
phased, interleaved, full-bridgeless PFCs by Synchronous rectification.
Figure 8 PFC Types such as –Conventional –Bridge Interleave –Bridgeless –Totem pole
PFC Performance
High Power Factor (PF) and low Total Harmonic Distortion (THD) are directly related, so the basic
circuits can be listed in performance order, as follows:
Conventional Boost PFC
−Low cost BOM solution.
Interleaved Boost PFC (High Power)
−Even though there still is a diode bridge, the continuous interleaved current offers the advantage
of using smaller components.
Bridgeless/Totem-Pole Bridgeless PFC (High Power)
−The diode bridge is replaced by a MOSFET semi-bridge / half-bridge Totem-Pole rectifier.
Bridgeless Interleaved PFC (High power)
−(Not shown) Enables use of successive expansion of multi-phase bridgeless interleaved boost
PFC.