Infineon TC2X4 User manual
User’s Manual
V 1.0 2014-10
Microcontrollers
32-Bit
Microcontroller
Application Kit TC2X4
Hardware: APPLICATION KIT TC2X4 V1.0
Hardware Manual
Edition 2014-10
Published by
Infineon Technologies AG
81726 Munich, Germany
©2014 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
User’s Manual
V 1.0 2014-10
Microcontrollers
32-Bit
Microcontroller
Application Kit TC2X4
Hardware: APPLICATION KIT TC2X4 V1.0
Hardware Manual
Application Kit TC2X4
Hardware Manual
User’s Manual V 1.0, 2014-10
Trademarks
TriCore®is a trademark of Infineon Technologies AG.
Application Kit TC2X4 User’s Manual
Revision History: V 1.0 2014-10
Previous Versions: –
Page Subjects (major changes since last revision)
–
–
–
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
User’s Manual L-1 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Application Kit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3 Application Kit Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Power via supply connector (X101) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.2 Power via Micro USB (BU301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.3 Multi Voltage Safety Micro Processor Supply TLF35584QV . . . . . . . . 3-1
3.2 Real Time Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 XGA Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3.1 Write a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.3.2 Read a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.3.3 Touch controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.4 Micro SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.5 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.6 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.7 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.7.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.7.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.8 Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.9 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.10 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.11 Ethernet (if supported by CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.12 Core current measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.13 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.14 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.15 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.15.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
4 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 IO Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.3 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.4 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.5 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.6 OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Table of Contents
User’s Manual L-2 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
5.7 Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
5.8 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
6 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.3 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
User’s Manual L-3 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Figure 2-1 Application Kit TC2X4 Block Schematic . . . . . . . . . . . . . . . . . . . . . . 2-3
Figure 2-2 Applcation Kit TC2X4 V1.0 Top Placement . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-3 Applcation Kit TC2X4 V1.0 Bottom Placement . . . . . . . . . . . . . . . . . 2-5
Figure 5-1 IO Connectors - Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Figure 5-2 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-3 USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-4 CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Figure 5-5 LIN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-6 OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-7 Ethernet connector pinout (RJ45) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 5-8 DAP connector pinout (FTSH10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 6-1 Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Figure 6-2 Schematic - CPU and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Figure 6-3 Schematic - Peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Figure 6-4 Schematic - miniWiggler JDS and OCDS1 . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-5 Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Figure 6-6 Component Plot Bottom Layer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Figure 6-7 Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-8 Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
List of Figures
User’s Manual L-4 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
User’s Manual L-5 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Table 4-1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-2 Reset Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-3 Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Table 4-4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
List of Tables
User’s Manual L-6 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Application Kit TC2X4
Hardware Manual
User’s Manual -7 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Introduction
User’s Manual 1-1 V 1.0, 2014-10
1 Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a
versatile tool, providing quick access to the capabilities of TriCore's powerful
architecture.
Applications can be developed easily. The Application Kit is equipped with a variety of
peripherals for connection to the environment. There is also an interface for the On Chip
Debugging Features.
The Application Kit allows easily the development of TriCore applications with the
corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful
debugger software.
This Application Kit Hardware Manual familiarizes you with the TriCore Evaluation Board
and guides you through the initial configuration of the Application Kit.
For detailed technical information about the TC2X4 (e.g. TC234, TC224) please refer to
the User Manual of the device.
Application Kit TC2X4
Hardware Manual
Introduction
User’s Manual 1-2 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-1 V 1.0, 2014-10
2 Application Kit Features
2.1 Summary of Features
– Infineon’s TC2X4 (e.g. TC234, TC224) Controller in TQFP-144 Package
– LCD XGA Display 320x240
– SD card slot (mini SD)
– High Speed CAN Transceivers
– USB to UART bridge
– Ethernet Gigabit PHY (if Ethernet supported by assembled CPU)
– LIN Transceiver
– Crystal 20MHz (default) or External Clock
– USB miniWiggler JDS for easy debugging
– 4Low Power Status LEDs
– RTC with alarm
– Acoustic beeper
– 100mm x 100mm
Connectors
The Application Kit TC2X4 Toffers a wide variety of connectors:
– Standard power connector
– Micro USB connector for ASC Interface (ASC0) and miniWiggler
– RJ45 connector for Ethernet (if Ethernet supported by assembled CPU)
– 16-pin header for JTAG interface (OCDS)
– 10-pin header for DAP
– 10pin (2x5) Header for LIN Transceiver (LIN)
– 10pin (2x5) Header for CAN High Speed Transceiver (CAN0)
– two 40-pin connectors with I/O signals
– mini SD card slot
Components
– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV
– LED to validate power supply (3,3Volt)
– LED indicating RESET (ESR0) active state
– LED indicating activ miniWiggler JDS
– LED switched via DAS software
– Infineon’s High Speed CAN-Transceiver TLE 6250 GV33
– Infineon’s LIN-Transceiver TLE 7259-2GE
– QSPI Real-Time Clock/Calendar with SRAM and unique MAC Id MCP79511
– USB to UART bridge FT2232HL (FTDI)
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-2 V 1.0, 2014-10
– Single Port Gigabit Ethernet PHY PEF7071 (LANTIQ, if Ethernet supported by
assembled CPU)
– Touch screen controller ADS7843
– 4 general purpose LEDs
– Reset switch
– Wake switch
– Xilinx CPLD XC9572XL
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-3 V 1.0, 2014-10
2.2 Block Diagram
Figure 2-1 Application Kit TC2X4 Block Schematic
Micro
USB miniWiggler
OCDS1
USB
XTAL
CAN
Transceiver
TxCAN0
RxCAN0
TC2X4
(e.g.
TC234,
TC224)
TriCore
CPU
PLL
CAN0
TX0
RX0
4 LED’s
(P13.0 up to
P13.3)
Multi Voltage Safety Micro
Processor Supply
TLF35584QV
RMII PHY Twisted Pair
RJ45
LIN
LIN
Transceiver
TX1
RX1
Micro
SD Card
QSPI0 Serial to
Parallel
converter
XGA Display
320x240
with touch
QSPI1
Acoustic
Beeper
P33.0
RTC
QSPI3
P33.7
WAKEUP
WAKE
QSPI2
QSPI2
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-4 V 1.0, 2014-10
2.3 Placement
Figure 2-2 Applcation Kit TC2X4 V1.0 Top Placement
DAP 1
1
1
APPLICATION KIT TC2X4 V1.0
CAN0
POWER
+5,5V...+40V
1
1
L1
RUN
1
ETH
LIN
ACT
JTAG
1
1
INFINEON TECHNOLOGIES AG
USB
SDCARD
U101
X302
X202
F
X205
X103
X102
X101
U102
+
LS101
L102
L101
C114
C107
X301
X201
U301
D302
BU301
D301
U203
X203
F
X204
U201
-
+
BT101
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-5 V 1.0, 2014-10
Figure 2-3 Applcation Kit TC2X4 V1.0 Bottom Placement
L4
WAKE
+3V3
/PORST
P13.3
P13.0
P13.1
P13.2
ESR0
1
LCD201
D104
S102
S101
D110 D109 D108 D107
D105
D106
SS2
Application Kit TC2X4
Hardware Manual
Application Kit Features
User’s Manual 2-6 V 1.0, 2014-10
Application Kit TC2X4
Hardware Manual
Application Kit Information
User’s Manual 3-1 V 1.0, 2014-10
3 Application Kit Information
3.1 Power Supply
The microcontroller needs 3 different supply voltages. This voltages are generated via
Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV (+3,3V and +5V
volt for ADC and CAN) and via the microcontroller itself (+1,3V).
Applying a stable supply voltage causes the power on reset after a short period. The
LED' (+3V3) indicate the status of the 3,3V voltage.
The board can be powered directly by USB or by the power connector. In case that the
voltage on the power connector is higher than the 5V from the USB then the board is
powered by power connector.
A manual power on reset is executed by pressing the reset button.
3.1.1 Power via supply connector (X101)
The Board has to be connected to a +5,5V to +40V DC power supply.
A supply with 6V and 500mA is sufficient. The pinout for the supply connector is shown
in Figure 5-2. There can be used any standard power pack with a connector where the
positive line is surrounded by the ground line.
3.1.2 Power via Micro USB (BU301)
The Board can also be powered by the Micro USB connector. The power consumption
of the board is approx. 400mA. Use an USB port which can deliver 500mA (USB 2.0) or
900mA (USB 3.0). Most USB hubs are not able to drive more than 100mA and can’t be
used.
Also it is possible to power the board with a cellular battery charger which has 5V output
and use Micro USB for connecting.
The pinout for the USB connector is shown in Figure 5-3.
3.1.3 Multi Voltage Safety Micro Processor Supply TLF35584QV
The board has assembled the Safety Micro Processor Supply with the following
Features:
• High efficient multi voltage power supply chip
• Serial step up and step down pre regulator for wide input voltage range from 3.0 to
40 V with full performance and low over all power loss
• Low drop post regulator 5.0V/200mA for communication supply (named LDO_Com)
• Low drop post regulator 3.3 V/600 mA (VS2) for μC supply (named LDO_μC)
• Provides enable, sync out signal and voltage monitoring (inside device to be added
to reset function) for an optional external post regulator for core supply (not used)
Table of contents
Other Infineon Microcontroller manuals
Infineon
Infineon XMC4000 series User manual
Infineon
Infineon CY8CKIT-062-WIFI-BT User manual
Infineon
Infineon XMC4000 series User manual
Infineon
Infineon IKW40N65WR5 User manual
Infineon
Infineon PSoC 4100S Max pioneer kit User manual
Infineon
Infineon XMC4000 series User guide
Infineon
Infineon High Side Switch Shield User manual
Infineon
Infineon XMC1100 User manual
Infineon
Infineon TDA7210V User manual
Infineon
Infineon XC2000 Easy Kit User manual
Infineon
Infineon XMC1400 User manual
Infineon
Infineon Traveo II Entry Family Starter Kit User manual
Infineon
Infineon XMC Series User guide
Infineon
Infineon PSoC 4000 Series Product manual
Infineon
Infineon XMC7000 Series Guide
Infineon
Infineon TLE9562 User manual
Infineon
Infineon XC164 Series Installation and operating instructions
Infineon
Infineon MOTIX TLE985xQX User manual
Infineon
Infineon XMC4000 series User manual
Infineon
Infineon Cypress PSoC 4500S Pioneer Kit User manual
