InFocus LP630 User manual

SP-CEIL-LM630
Projector Mount
INSTALLATION INSTRUCTIONS
qStep 1
Place warning label on lamp door where indicated. Invert the
projector and place it on a soft and flat surface.
Locate the four (4) 4 (mm) mounting points found on the bottom
of the projector. Secure the three (3) Quick release sleeves (D)
withthethree(3)4(mm)x16(mm)PhillipScrews(C)
(supplied). Align the keyhole openings from the mounting
bracket (B) to the sleeves (D) and secure the bracket with the
4 (mm) x 12 (mm) knurl knob(A) (supplied). Do not over
tighten!
See Figure 1
qStep 2
Install the base box securely to the ceiling structure in
accordance with proper commercial standards. Use
(commercially available) suitable hardware depending on the
installation requirements.
NOTE:If the (Optional) SP-LTMT-EXT adjustable height
suspension adapter is a part of the installation, securely install
the ceiling adapter to the ceiling at this time.
(Refer to its Installation Instructions)
qStep 3
Install the two (2) conical spacers (J) and two (2) flat washers (K), two
(2) hinge screws (L) loosely on both sides of the base box (H). Raise
the projector with the mounting bracket attached and slip though the
hinge pin slots openings on the bracket into the base box. Install the
two (2) angle locking screws (I) adjust the angle, lock it, and then
tighten the hinge pin screws.
See Figure 2
qStep 4
Check all the hardware for proper tightness and security. Do not
over tighten hardware.
PORTABLEPROJECTORS
(1) Remove the knurl knob screw and hold the projector with
two hands.
(2) Slide it backwards to detach the sleeves from the keyholes.
(3) Reverse the process for quick reinstall.

qStep 5
Raise the projector with the mounting bracket (B) and slip through the
hinge pin slot openings on the bracket into the base box (H). Loosely
install the two (2) hinge pin screws (L), conical spacers (J) and flat
washers (K) and the angle lockingscrews (I). Adjust the angle and lock
it. Then tighten the hinge pin screws (L). Donot overtighten
See Figure 3
Check all hardware for proper tighten and security.
-_LA 073001_-
The ceiling should be capable of supporting a weight of
at least five (5) times the projector(s) or monitor(s)weight.
If it cannot, the ceiling must be reinforced. Proper
installation procedure by qualified personnel as outlined
in the installation instructions must be adhered to.
Failure to do so could result in serious personal injury.
To prevent eye injury wear protective eyewear before
openinglamp door.
DESCRIPTION/HARDWARE
A.4 (mm) x 12 (mm) Knurl Knob (1ea)
B. SP-CEIL-LM630 Mounting Bracket (1ea)
C. 4 (mm) x 16 (mm) Phillip Screws (3ea)
D.4 (mm) Quick Release Sleeves (3ea)
E.Projector (not supplied)
F. Ceiling Structure (See Warning Label)
G. Suitable Hardware (Commercially Available)
H.Base Box/Jam Screw (1ea)
I. 6 (mm) x 12 (mm) Angle Locking Screws (2ea)
J. Conical Spacer (2ea)
K.FlatWashers(2ea)
L.6 (mm) x 12 (mm) Hinge Pin Screws (2ea)
M.SP-LTMT-EXT Adjustable Suspesion Adapter (Optional)
N. Suspension Adapter Ajustable Pins (2ea)
27700B S.W. Parkway Ave.
Wilsonville, Oregon 97070-9215
Phone [phone] Fax
www.infocus.com
For further in
formation or ordering assistance
contact us at the phone/address number shown
on the front of this page.