Ink Bird ITC-608T User manual

ITC-608T
Manual

Part 1Quick Guide to Use
The Manual
Is Divided Into
6Parts.
Part 2Temperature Controller Manual
Part 3Programmable Temperature
Controller Manual
Part 5Humidity Controller Manual
Part 6Humidity&Temperature
Controller Manual
1
4
12
36
Part 4Dual Temperature Probes
Controller Manual
26
43

PAGE 12
PAGE 26
1.CAUTION:
KEEP CHILDREN AWAY
TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY
INDOORS
RISK OF ELECTRIC SHOCK. DO NOT PLUG INTO ANOTHER
RELOCATABLE POWER TAPS OR AN EXTENSION CORD.
USE ONLY IN DRY LOCATION
TEMPERATURE
Controller Manual
Equivalent to ITC-308
Temperature Controller Manual
PROGRAMMABLE
TEMPERATURE
Controller Manual
Equivalent to ITC-310T-B
Temperature Controller Manual
ITC-608T ITC-608T
Temperature
Control Mode
ITC-608T + Temperature Probe
2.Quick Guide
1
PAGE 4
Part 1
Part 2Part 3
Quick Guide to Use
The instruction manual will skip to the corresponding page
according to the probe you select.
Dual Temperature Probes
Control Mode
ITC-608T + Dual Temperature
Probes
DUAL TEMPERATURE
PROBES
Controller Manual
ITC-608T
Part 4

3. Specification
Power
Voltage: 120Vac 60Hz
Current: 15A
Wattage: 1800W
Temperature Probe (optional)
Type of temperature probe：R25°C=100KΩ±1%,
R0°C=26.74~27.83KΩ , B25/85°C=3435K±1%
Temperature measurement range：-40°C~100°C/-40°F~212°F
Temperature display accuracy：0.1°C/°F(<100°C/°F)，
1°C/°F(>=100°C/°F)
Temperature measurement accuracy：
Range of Temperature
Celsius
Celsius Error
Range of Temperature
Fahrenheit
Fahrenheit Error
-40℃≤T<10 ℃±2 ℃-40℉≤T<50 ℉±3 ℉
10℃≤T<80 ℃±1 ℃50℉≤T<176 ℉±2 ℉
80℃≤T≤100 ℃±2 ℃176℉≤T≤212 ℉±3 ℉
Humidity Probe(optional)
Type of humidity probe：HTG3515CH
Relative humidity measurement range：5~99%RH
Humidity display accuracy：0.1%RH
HUMIDITY
Controller Manual
Equivalent to IHC-200
Humidity Controller Manual
ITC-608T
TEMPERATURE
HUMIDITY
Controller Manual
Equivalent to IHC-230
Temperature & Humidity
Controller Manual
ITC-608T
Humidity
Control Mode
ITC-608T + Humidity Probe
Temperature and Humidity
Control Mode
ITC-608T + Temperature Probe
+Humidity Probe
2
Part 5
36
PAGE 43
Part 6
PAGE

4. Technical Assistance and Warranty
4.1 Technical Assistance
If you have any problems installing or using this controller,
please carefully and thoroughly review the instruction
manual. If you require assistance, please write us
to [email protected].We will reply your emails
in 24 hours from Monday through Saturday.
You can also visit our web site www.ink-bird.com to find the
answers of the common technical questions.
4.2 Warranty
INKBIRD TECH. C.L. warrants this controller for two years
(temperature and humidity probe for one year) from the date
of purchase when operated under normal condition by the
original purchaser (not transferable), against defects caused
by INKBIRD’s workmanship or materials. This warranty is
limited to the repair or replacement, at INKBIRD’s discretion
of all or part of the controller. The original receipt is required
for warranty purposes.
3
Relative humidity measurement accuracy(10%~95%RH)：
Typical value±3%RH, Maximum value±5%RH
Display unit：temperature：Celsius °C or Fahrenheit °F；
humidity：%RH
Ambient
Ambient temperature：-20°C~60°C/-4°F~140°F
Storage environment：temperature：0°C~60°C/32°F~140°F；
humidity：20~80%RH(Unfrozen or condensation state )
Warranty
Controller: Two years warranty
Temperature and Humidity Probe: One year warranty

4
TEMPERATURE
Controller Manual
Equivalent to ITC-308
Temperature Controller Manual
ITC-608T
Part 2

5
86.8
f
96.0
f
WORK1 WORK2
A
B C D
E
F
P1 P2
1Get to Know the Controller

6
Functions on screen
PV：In normal mode, the measured temperature is displayed.
In settings mode, it will display menu code.
SV：In normal mode, the temperature setting value is
displayed. In setting mode, it will display the setting value.
Output(WORK1/WORK2) Instruction
WORK1: The heating output
WORK2: The cooling output
Indicator LED:
●Red LED is on WORK1 output is on.
●Green LED is on WORK2 output is on.
●Green LED is blinking WORK2 output is performing the
function of compressor delay.
●Yellow LED is on The controller is in the setting mode.
Button Instruction
Please read the detail on 2.Button Operation Instructions below.
Probe interface
Temperature probe can be insert into P1 or P2 interface.
Temperature probe
If the controller display Er, you may get a false temperature
probe, please try harder to insert the probe and rotate it to
make good contact. If the problem is still persists, it is likely the
internal probe wire has been damaged by the moisture or heat
temperature.
The probe and cable cannot be touched by the flame.
Do not exceed the probe temperature range to avoid
damaging.
A
B
D
E
F
C

7
2Button Operation Instructions
2.1 Restore Default Settings
Press the “ " button to power on, the buzzer will make a
short call, indicating that all parameters of the user's
temperature probe function return to the default setting value.
2.2 “ ” and “ ”Button Function in Normal Operation
Mode
Press “ ", PV shows HD, SV shows heating difference value;
press “ ", PV shows CD, SV shows cooling difference value,
and It will be back to the normal display if there is no
operation for 3 seconds or pressing the "SET" button.
2.3 “SET” Button Function in Normal Operation Mode
Short press the “SET” button to enter the quick setting
temperature value mode. SV shows the temperature setting
value and flashes, and short press “ ” or “ ” button to
increase or decrease the setting value, long press “ ” or
“ ”button to quickly increase or decrease the setting value,
finally press the “SET" button again to confirm and exit. If
there is no operation, it will automatically exit after 10
seconds and save the setting value.
2.4 Button Function in Setting Mode
When the controller is working normally, press the “SET”
button for 2 seconds to enter the setting mode, the PV screen
shows the first menu code “TS” and the SV shows the
corresponding setting value. Press “SET” button to scroll
down the menu item and save the parameters of the previous
menu item. Press “ ” or “ ”button to change the current
setting value. If in the setting state, there is no button
operation within 30 seconds or long press “SET" button for 2
seconds, exit and save the setting state, return to normal
operation mode.

8
3 Menu Instruction
3.1 Setting mode Flow Chart
Temperature Setting Value
Heating difference value
Cooling difference value
SET
Alarm High Temperature Limit
Alarm Low Temperature Limit
Compressor Delay Time
Temperature Calibration
Temperature Unit
Press "SET" Key for over 2
seconds to enter parameters
setting mode
TS
77.0℉
HD
CD
AH
AL
PT
0Minute
CF
F
CA
No Key for 30 seconds or
Presss "SET" key for over 2
second ?
Working normally
SET
SET
SET
SET
SET
SET
SET
SET
SET
TR=0

9
3.2 Setting Menu Instruction
Code Symbol Function Setting Range
Default
Settings
Annotation
TS tS Temperature Setting
Value
-40.0℃～100℃
25.0
℃
-40.0℉~212℉77.0 ℉
℉
HD Heating Difference
Value
0.3℃～15.0℃2.0 ℃
1.0℉~30.0℉3.0 ℉
℉
CD Cooling Difference
Value
0.3℃～15.0℃2.0 ℃
1.0
℉
~30.0
℉
3.0
℉
AH AH Alarm High
Temperature Value
-40.0
℃～
100
℃
100
℃
-40.0℉~212℉
212
℉
℉
AL AL Alarm Low
Temperature Value
-40.0℃～100℃- 40.0 ℃
-40.0℉~212℉- 40.0 ℉
PT
C
ompressor Delay 0～10 minutes 0 minute More details on 4.3
More details on
4
.
More details on 4.1
CA CA Temperature
Calibration
-9.9 ℃～ 9.9 ℃0.0 ℃More details on 4.4
-
15.0
℉
~15.0
℉
0.0
℉
CF CF Fahrenheit or
Celsius
Setting
C or F F More details on 4.5
TR Timer Setting 0、1 or 2 0 More details on 4.6
4 Control Function Instruction
When the controller works normally, the PV shows the
measured temperature, meantime the SV screen shows the
temperature setting value, and automatically recognizes and
converts for the heating or cooling working mode , in which
WORK1 is the heating output, furthermore the red led is the
WORK1 heating output status indicator;WORK2 is cooling
output, furthermore the green led is WORK2 cooling output
status indicator.
4.1Instructions for SettingTemperature Control (TS,HD,CD）
4.1.1 Normal Temperature Control：
When the measured temperature PV ≤ TS(Temperature Setting
Value) – HD(Heating difference value),the controller will enter
the heating state, the red led is on, WORK1 output works.
When the measured temperature PV ≥ TS(Temperature Setting
Value), the red led is off and the WORK1 output turns off.
When the measured temperature PV ≥ TS(Temperature Setting
Value) + CD(Cooling difference value), the controller will enter
the cooling state, the green led is on, WORK2 output works;
the green led flashes, indicating that the cooling device is in
the state of the Compressor delay protection. When
PV(measured temperature) ≤ TS(temperature setting value),
H
C
P
.2

10
the green led is off and the WORK2 output turns off.
For example, setting TS=25.0°C, CD=2.0°C, HD=3.0°C, when
the measured temperature value ≤ 22°C (TS-HD), the
controller will enter the heating state; when the measured
temperature value ≥ 25°C, the heating will stop; when the
measured temperature value ≥27.0°C(TS+CD),the controller
enter the cooling state; when measured temperature value ≤
25.0°C, cooling will stop.
4.1.2 Special Temperature Control
There is no need to judge the difference value in heating or
cooling when power on or exiting the setting state, it directly
compare with TS(temperature setting value).
For example: When power on or exiting the setting state,
TS=25.0°C, CD=2.0°C, HD=3.0°C. If PV( measured temperature
value) >25.0°C, it enters the cooling state. When PV(measured
temperature value) ≤25.0°C, the cooling stops. Then return to
normal temperature control. When PV(measured temperature
value) <25.0 °C, it enter the heating state, when PV(measured
temperature value) ≥ 25.0 °C, heating stops, and then return to
normal temperature control.
4.2 Alarm High / Low Temperature Limit Settings(AH,AL）
When measured temperature ≥ AH, high temperature limit
alarm, then will turn off heating and cooling output, PV shows
alternate AH with current temperature, buzzer will “bi-bi-Biii”
alarm, until the temperature <AH, buzzer off and return to
normal display and control. Or press any button to turn the
buzzer alarm off only.
When measured temperature ≤ AL, low temperature limit
alarm, then will turn off heating and cooling output, PV shows
alternate AL with current temperature, buzzer will “bi-bi-Biii”
alarm, until the temperature >AL, buzzer off and return to
normal display and control. Or press any button to turn the
buzzer alarm off only.

11
4.3 Compressor Delay Time（PT）
In the cooling mode, when the power is turned on for the first
time, PV(measured temperature value) ≥ TS(Temperature
setting value) + CD(Cooling difference value), it will not start
cooling immediately, but waiting for a delay time(PT).
When two adjacent of cooling starting intervals are greater
than the delay time, it will immediately start cooling; When two
adjacent of cooling starting intervals are less than the delay
time, it needs to operate the remaining delay time to start the
cooling.
Delay time will start counting from the cooling output off.
4.4 Temperature Calibration(CA）
When the measured temperature deviates from the standard
temperature, the temperature calibration function can be used
to make the measured value of the instrument consistent with
the standard value. The calibrated temperature=the measured
temperature + the calibration value.
4.5 Fahrenheit or Celsius Settings (CF）
The users can set the display unit to Fahrenheit or Celsius
according to their habits. The default temperature is
Fahrenheit. If you need to display the unit in Celsius, then set
the CF to C. Please note that when the CF changes state, all
setting values are restored to the default setting and the
buzzer gives a short beeping prompt.
4.6 Timer Setting (TR）
TR is the parameter for whether the timer function is enabled.
0 is off and 1 or 2 is on. If user set TR=1 or 2,please see Part 3

12
PROGRAMMABLE
TEMPERATURE
Controller Manual
Equivalent to ITC-310T-B
Temperature Controller Manual
ITC-608T
Part 3

13
86.8
f
96.0
f
WORK1 WORK2
A
B C D
E
F
P1 P2
1Get to Know the Controller

14
Functions on screen
PV：In normal mode, the measured temperature is
displayed. In settings mode, it will display menu code.
SV：In normal mode, the temperature setting value is
displayed. In setting mode, it will display the setting value.
Output(WORK1/WORK2) Instruction
WORK1: The heating output
WORK2: The cooling output
Indicator LED
●Red LED is on WORK1 output is on.
●Green LED is on WORK2 output is on.
●Green LED is blinking WORK2 output is performing the
function of compressor delay.
●Yellow LED is on The controller is in the setting mode.
Button Instruction
Please read the detail on 2.Button Operation Instructions
below.
Probe interface
Temperature probe can be insert into P1 or P2 interface.
Temperature probe
If the controller display Er, you may get a false temperature
probe, please try harder to insert the probe and rotate it to
make good contact. If the problem is still persists, it is likely
the internal probe wire has been damaged by the moisture or
heat temperature.
The probe and cable cannot be touched by the flame.
Do not exceed the probe temperature range to avoid
damaging.
.
A
B
D
E
F
C

15
2 Button Operation Instructions
2.1 Restore Default Settings
Press the " " button to power on, the buzzer will make a
short call, indicating that all parameters of the user's
temperature probe function return to the default setting
value.
2.2 Start Controlling Temperature from the First Stage
Forcibly
When TR=1 or 2, press the increase button “ ”to power on,
the buzzer will make a short call, indicating the user that
will start controlling temperature from the first stage
forcibly.
2.3 “ ”and“ ”Button Function in Normal Operation
Mode
2.3.1 When TR=0
Press “ ”, PV shows HD, SV shows heating difference
value. Press “ ”，PV shows CD，SV shows cooling
difference value.
2.3.2 When TR=1 or 2
Press “ ”PV shows current time unit, SV shows the
current remaining working time; And It will be back to the
normal display if there is no operation for 3 seconds or
pressing the "SET" button. Press “ ”，PV shows the
current stage，SV shows the setting value of current stage.
And It will be back to the normal display if there is no
operation for 3 seconds or pressing the "SET" button.
2.3.3 When TR=1 or 2
press “ ”and“ ” simultaneously for one second, it will
start operating from the SST setting forcibly，at the same
time，the buzzer will give a short beeping prompt.
2.4 “SET” Button Function in Normal Operation Mode
Short press the “SET” button to enter the quick setting
temperature value mode. When TR=0, SV displays the
temperature setting value and flashes. Short Press “ ” or
“ ” button to increase or decrease the temperature
setting value. Long Press“ ”or“ ”button to quickly

16
increase or decrease the temperature setting value, then press
"SET" button to confirm and exit. When TR=1 or 2,SV shows
the temperature setting value and flashes, then short press
“ ” or “ ” button to increase or decrease the temperature
setting value. Long press the“ ” or “ ”button to increase or
decrease the temperature setting value quickly. Press the
"SET" button to switch to the current stage control duration
value. Short press the “ ”or “ ” button to change the
current stage control duration value. Press the “SET" button to
switch to whether to alarm after the completion of the current
stage, then press “ ” or “ ” to modify the setting value .
Press “SET” button again to confirm and exit. If there is no
operation for 3 seconds ,It will automatically exit after 10
seconds and save the setting value.
2.5 Button Function in Setting Mode
When the controller is working normally, press the “SET”
button for 2 seconds to enter the setting mode. The PV shows
the first menu code “TS”, if TR=1 or 2, the PV shows the
second menu code“ HD”, SV shows the corresponding setting
value. Press “SET” button to scroll down the menu item and
save the parameters of the previous menu item. Press “ ” or
“ ” button to change the current setting value. If in the
setting state, there is no operation within 30 seconds or long
press "SET" button for 2 seconds, it will exit and save the
setting state and return to normal operation mode.

17
……
3 Menu Instruction
3.1 Menu Setting Flow Chart
Time Unit: D(Day),
H(Hour)or M(Minute)
Cycle Mode 1~999,
MD=0 Infinite Cycle
N
YAfter the power off,
re - running
mode: 0->manual,
1->automatic
Temperature Setting Value
Stage Value 1~12
Heating difference value
Start Stage Value
Cooling difference value Stage1：Temperature
Setting Value
SET
Alarm High
Temperature Limit Stage1:Duration Length
Alarm Low
Temperature Limit Stage1:User Defined Alert
at the end of stage1
The Qty of stages depend
on the STT Value
Compressor Delay Time
Stage12：Temperature Set Value
Temperature Calibration
Stage12:Duration Length
Temperature Unit Stage12:User Defined
Alert
at the end of stage12
Y
U1~U12:
Nn:No Alert
A:Alert
C:Confirm
S:Stop Program
TR=0:Simple Mode
TR=1:Continious Timer Mode
TR=2:Target Timer Mode
Press "SET" Key for over 2
seconds to enter parameters
setting mode
TR = 0 ?
TS
77.0℉
HD
CD
AH
AL
PT
0Minute
CF
F
CA
TR = 1or TR=2?
UT
M
MD
1
AT
0
STT
1
SST
1
S01
77.0℉
H01
10
U01
n
S12
H12
10
U12
n
No Key for 30 seconds or
Presss "SET" key for over 2
second ?
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
Working normally

18
3.2 Setting Menu Instruction
Code Symbol Function Setting Range
Default
Settings
Annotation
TS tS Temperature Setting
Value
-40.0℃～100℃
25.0℃
-40.0
℉
~212
℉
77.0
℉
℉
HD HHeating Difference
Value
0.3℃～15.0℃2.0℃
1.0℉~30.0℉3.0℉
℉
CD CCooling Difference
Value
0.3℃～15.0℃2.0℃
1.0℉~30.0℉
3.0℉
AH AH Alarm High
Temperature Value
-40.0
℃～
100
℃
100
℃
-40.0
℉
~212
℉
212
℉
℉
3.2.1 When TR=1 or 2, menu code setting is as below.
Code Symbol Function Setting Range
Default
Settings
Annotation
UT UTime Unit Setting
Value
D ：Day, ：Hour, ：
Minute
MD Cycle Setting Value 0-999 1
When is 00
，
infinite
loop
AT
A
Auto or Manual Mode
0 or 1
0
0:Manually, 1:Automatic
STT S
Time Stage Setting
Value
1-12 1 More details on 4. 6.4
SST SS
Start Stage Settings
Value
1~12 1 More details on 4. 6.5
3.2.2
When STA is set to 12, menu code setting is as below.
Code
Symbol
Function
Default Settings
Annotation
S01 S01 Stage 1 Temperature Setting Value 25.0℃or 77.0℉*
H01
H01
Stage 1 Control Duration Value
10
**
U01 U01
Whether to Alarm after the Completion of
Stage1
n ***
S02 S02 Stage 2 Temperature Setting Value 25.0℃or 77.0℉*
H02
H02
Stage 2 Control Duration Value
10
**
U02 U02
Whether to Alarm after the Completion of Stage
2
n ***
S03
S03
Stage 3 Temperature Setting Value
25.0℃or 77.0℉
*
H03
H03
Stage 3 Control Duration Value
10
**
U03 U03
Whether to Alarm after the Completion of Stage
3
n ***
S04
S04
Stage 4 Temperature Setting Value
25.0℃or 77.0℉
*
H04
H04
Stage 4 Control Duration Value
10
**
U04 U04
Whether to Alarm after the Completion of Stage
4
n ***
S05
S05
Stage 5 Temperature Setting Value
25.0
℃or
77.0
℉
*
H05
H05
Stage 5 Control Duration Value
10
**
U05 U05
Whether to Alarm after the Completion of Stage
5
n ***
S06 S06 Stage 6 Temperature Setting Value 25.0℃or 77.0℉*
H06
H06
Stage 6 Control Duration Value
10
**
U06
U06
Whether to Alarm after the Completion of Stage
n
***
AL AL Alarm Low
Temperature Value
-40.0℃～100℃-40.0℃
-40.0℉~212℉-40.0℉
PT PCompressor Delay
0～10 minutes
0 minute More details on 4.3
CA CA Temperature
Calibration
-9.9℃～9.9℃0.0℃More details on 4.4
More details on 4.1
More details on 4.2
-15.0
℉
~15.0
℉
0.0
℉
CF CF
Fahrenheit or Celsius
Setting
C or F F More details on 4.5
TR Timer Setting 0、1 or 2 0 More details on 4.6.2
6
S07
S07
Stage 7 Temperature Setting Value
25.0℃or 77.0℉
*
H07
H07
Stage7 Control Duration Value
10
**
U07 U07
Whether to Alarm after the Completion of Stage
7
n ***
S08
S08
Stage 8 Temperature Setting Value
25.0℃or 77.0℉
*
H08
H08
Stage 8 Control Duration Value
10
**
U08 U08
Whether to Alarm after the Completion of Stage
8
n ***
S09
S09
Stage 9 Temperature Setting Value
25.0
℃
or 77.0
℉
*
H09
H09
Stage 9 Control Duration Value
10
**
HH