INNOVAPLAS BILTMOR 5015 User manual

REV. 02/12/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
Required tools (not included)
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
20 lbs
x6 x6 x6
A B C
Phillips #2 Phillips #3 7/16 wrench
Phillips bit
BILTMOR 5015 WITH CLASSIC LADDER 6003
Contents of the Biltmor box SKU # 5015
Security straps
x2
x2 x2 x2
(3/4 IN.)
x18
2 1/2 IN.)
x2
SCREW BAG 140-0058
(1 IN.)
FA D B C
Contents of the ladder box SKU # 6003
x2
x2
x2
x2
MAXIMUM functional
width is 1/4’’.
A weather-resistant
padlock is recommended
(not included).
3/8 drill bit
SCREW BAG 140-0036
x6 x6 x6
(1 IN.)
(³⁄4IN.)
x2
(³⁄4IN.)
x13
AB C D E
x2
x2
x3
x2
x2
Maximum weight: 300 lbs / 136 kg.

REV. 02/12/2020 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
BC
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
D
E
G
F
E
BILTMOR 5015 WITH CLASSIC LADDER 6003
x13
1) Insert the two large posts and the 35”
post into the post ends and secure
them in place with the screws provided
(see medallion).
2) Insert the platform over the two rear
posts.
3) Insert the small and large handrails
as illustrated. Secure the large handrail
with the screws provided. Leave the
small handrails floating.
4)
Fasten the access panel with the screws
provided.
D
’3
1/4
’
1/4”
align screws from
center of plate
x2
x3
D
E
Sand
20 lbs
1) Insert a 20 lbs (9 kg)
sand bag on the third step,
as shown.
1) Slowly submerge the step into
the pool. Make sure you do not
damage the pool liner in the
process.
2) Angle the whole step so that it
is entirely under water. Purge all
the air from under the step.
Security strap
1) Once the step is in
the pool secure the
platform to the top
seat (see illustration)
using the two straps
provided.
x2
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the
2 screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
x2
F
1) Trace a line on each post at 39 inches from the
ground for 48’’ and 52’’ pools. If you have a 54’’ pool,
trace a line at 40.5 inches from the ground.
2) Slide the pivot blocks onto the posts and line up
with the traced marks. Secure with the screws
provided.
3) Attach the ladder base to the bottom of the posts
with the screws provided.
4) Slide the posts through the platform. Slide the lock
over right post between the platform and the handrail.
Secure the platform using the screws provided.
5) Slide the posts through the handrails. Insert the post
covers into the handrails. If they protrude too much,
raise the handrails until the post covers are seated
securely on the posts. Secure the short handrails in
place with the screws provided.
x18
D
A
D
align for 48''
& 52'' pools
align for 54’’
1) Snap the three post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the filler post end into the step
as shown.
3) Snap the two feet to the bottom of
the step.
FILLER
35” post
A
LOCK

REV. 02/12/2020 PN: PG:3
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
H
BILTMOR 5015 WITH CLASSIC LADDER 6003
SWING THE LADDER UP
AND LOCK IN PLACE WHEN
THE POOL IS NOT IN USE
TO PREVENT DROWNING
AND UNAUTHORIZED
ENTRY.
WARNING
Use sliding lock as a guide to drill hole into
ladder in up position. Use a 3/8’’ drill bit with
a cordless drill.
**PADLOCK REQUIRED**
1) Attach the ladder tothe pivot blocks with
the bolts, washers and nuts provided.
x2
x2
x2
A
B
C