INNOVAPLAS Lumi-o BILTMOR DECK 5050 User manual

REV. 02/26/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
BILTMOR DECK 5050
Required tools (not included)
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Contents of the Biltmor box SKU # 5050
x4
x2
x2
x4
x2
x2
Contents Riser kit
x2
Sand
(not included)
Sand
5 lbs
x6 x6 x6
A B C
Phillips #2 Phillips #3
7/16 wrench
Phillips bit
x2 x4
x2
(3/4 IN.)
x4
D
SCREW BAG 140-0067
x6 x6 x6
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x2
(³⁄4 IN.)
x24 x12
AB C D E F
SCREW BAG 140-0010

REV. 02/26/2020 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
BILTMOR DECK 5050
BC
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
1) Snap the four post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the two feet to the bottom of
the step.
D
E
F
1) Insert the four posts into the post ends and secure
them in place with the screws provided (see medallion).
2) Insert the two deck supports over the
rear posts.
3) Insert the handrails on the two posts
and secure in place.
4) Fasten the access panel with the
screws provided.
’3
1/4
’
1/4’’
align screws from
center of plate
1) Slide the two tie
wraps in place and
place the sand bag
into the riser. Fasten
the tie wraps. Do not
over tighten.
1) Slowly submerge the
step into the pool. Make
sure you do not damage
the pool liner in the process.
2) Angle the whole step so that it is entirely under
water. Purge all the air from under the step.
1) Fill the bag provided
with sand. The approximate
weight should be 5 lbs.
*SAND
*Sand not included
x20
G
x2
E
D
D
4x
4x
x3
D
1) Insert the two step cups in the riser.*
2) Place the riser on the ground, install the step
on top of the riser and fasten with the four
screws and plastic screw caps provided.
3) Snap the screw caps covers in place.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0

F
x12
D
F
x4
D
REV. 02/26/2020 PN: PG:3
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
BILTMOR DECK 5050
I
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
1) Pull the deck supports (already fixed to
the deck) upwards to create a spring effect
on the step.
2) Fasten the supports to the two rear posts
while pushing the entire step downwards.
H
1) Affix the deck supports to the deck
with the screws supplied.
2) Install the two post covers.