INNOVAPLAS Lumi-O MAJESTIC 8005 User manual

WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
MAJESTIC 8005 WITH DECK
Sand
15 lbs
Sand
Contents of accessory box Majestic step Shell
(not included)
SCREW KIT 140-0027
A1) Assemble the two
handrail halves.
2) Insert the handrail
into the recesses.
3) Fasten the handrail
to the step using the
screws, washers and
nuts provided.
x6
x4 x4 x4
(3 IN.)
(1 ¹⁄2 IN.)
x10
(³⁄4 IN.)
x6
AB C D E
Required tools (not included)
Phillips #2
Phillips #3 7/16 wrench
Phillips bit
x2
DB
x6
B3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely.
.
CAUTION Failing to install the Step CupTM system will greatly reduce the steadiness of the step and will void the
manufacturer warranty.
Insert the six Step CupsTM in the holes under
the step.*
B1) Insert half of the Step
Cup mushroom ring in
the hole, at a 45 degree
angle.
B2) With a flat screwdriver, compress the Step
Cup mushroom ring while pushing it into the hole.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
REV. 03/05/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
A
x4
x4
x4
B
C

E
DECK
TOP SEAT
MAJESTIC 8005 WITH DECK
D
POOL DECK ABOVE POOL TOP SEAT
POOL TOP SEAT FLUSH WITH DECK POOL
POOL DECK OFFSET FROM TOP SEAT
POOL DECK OFFSET FROM TOP SEAT
HOW TO MOUNT
YOUR DECK SUPPORT
FOR YOUR POOL
x10
1) Affix the deck support to the handrail’s
vertical post using the 4 screws provided.
2) Align the step carefully and fasten
the deck support to the deck, as shown
below.
3) Drop the ballast in the
step hole.
DECK
TOP SEAT
DECK
TOP SEAT
Spacer block not included
DECK
SPACER BLOCK
NOT INCLUDED
REV. 03/05/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
C
MINIMUM 1" All Step Cups
TM
must be installed.
Sand
15 LB
1) Fill the ballast
with sand. The
approximate weight
should be 15 lbs.
CAUTION
To prevent pool liner puncture, keep a minimum 1" gap
between the pool liner and the rear underside of the step.
Align holes
2) Screw the lid in place
and align the cover ribs
with the holes in the
ballast base.
3) Fasten the cover to the
ballast base with the four
screws provided.
x4
D
4) Slowly submerge the
step into the pool. Make
sure you do not damage
the pool liner in the
process.
5) Angle the whole step
so that it is entirely under
water. Purge all the air
from under the steps.
6) Slide the deck support
to the height of the deck.