INNOVAPLAS BILTMOR 5001 User manual

REV. 02/07/2023 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
Maximum weight: 300 lbs / 135 kg.
Required tools (not included)
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
15 lbs
x6 x6 x6
A B C
Phillips #2 Phillips #3 7/16 wrench
Phillips bit
BILTMOR 5001 WITH SELF-LATCHING 9600
Sand
15 lbs
Contents of the Biltmor box SKU # 5001
Security straps
x2
x2 x2
(3/4 IN.)
x12
(2 1/2 IN.)
x2
SCREW BAG 140-0016
(2 1/2 IN.)
FG D C
Contents of the Self-Latching box SKU # 9600
MAXIMUM functional
width is 1/4’’.
A weather-resistant
padlock is recommended
(not included).
x2
x4
x3
SCREW BAG 140-0020
x6 x6 x6
(1 IN.)
(³⁄4IN.)
x2
(³⁄4IN.)
x20
AB C D E
x4
x2
x2 x4
x2
x2

REV. 02/07/2023 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
B C
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
1) Snap the four post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the two feet to the bottom of
the step.
D
E
G
F
H
BILTMOR 5001 WITH SELF-LATCHING 9600
x20
1) Insert the four posts into the post
ends and secure them in place with the
screws provided (see medallion).
2) Insert the platform over the 2 rear
posts.
3) Insert the small and large handrails
as illustrated. Secure the large
handrails with the screws provided.
Leave the small handrails floating.
4)
Fasten the access panel with the screws
provided.
D
’3
1/4
’
1/4”
align screws from
center of plate
x2
x3
D
E
Sand
15 lbs
Sand
15 lbs
1) Insert 2 15 lbs (7 kg)
sand bags on either side of
the third step, as shown.
1) Slowly submerge the step into
the pool. Make sure you do not
damage the pool liner in the
process.
2) Angle the whole step so that it
is entirely under water. Purge all
the air from under the step.
Security strap
1) Once the step is in
the pool secure the
platform to the top
seat (see illustration)
using the two straps
provided.
x2
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the
2 screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
x2
F
1) Insert the two posts into
the rear holes of the step.
2) Force the posts to a
vertical position flush with
the rear surface and
secure in place with the
bolts and nuts provided.
3) Insert the two post
covers.
x2
x2
G
C
1) Slide the Self-Latching
posts through the
platform and small
handrails.
2) Secure the platform
using the screws
provided.
3) Secure the small
handrails to the posts
with the screws provided.
4) Insert the four post
covers on the handrails.
x12
D

REV. 02/07/2023 PN: PG:3
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
BILTMOR 5001 WITH SELF-LATCHING 9600
WARNING
LOCK THE DOOR TO THE
STEP WITH A PADLOCK
WHEN THE POOL IS NOT
IN USE TO PREVENT
DROWNING AND
UNAUTHORIZED ENTRY.
I