Inside Weather ASHBY HEADBOARD User manual

ASHBY HEADBOARD

Gather Your Eggs...
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
Headboard Tiles (Amount and Length Depend on Configuation)
Uprights (Amount, Length and Hole Quantity Depend on Configuration
Not included: Pencil for marking mounting locations, measuring tape, screwdriver
Level
Screws Drywall Anchors

Desired Height
Center of Bed
Distance between Uprights
Right Upright Center
Left Upright Center
Reference Diagram
Assembled Headboards: Front Assembled Headboards: Back

Step 1: Mark Your Center Height
Step 2: Mark Outside Center Widths
Mark your desired height by placing a
crosshair at the center of where your
headboards will be mounted. Headboard
will stick up 3⁄8 of an inch from this mark.
Mark distance ‘A’ from center point for
left and right uprights.
UprightsPanelsAssembled Headboard
A A
HEADBOARD SIZE DISTANCE “A”
Twin 19.5”
Full 30.5”
Queen 30.5”
King 38.5”
Cal King 38.5”
CenterLeft Width Right Width
A A

Step 3: Mark Your Upright Height
Step 4: Mark Upright Width
Step 5: Remeasure
Measure and mark 1.5” on
each side of the center
vertical lines for all your
uprights.
You should end up with
markings for every upright like
the diagram shown here.
Remeasure all lines to verify you have marked the
correct locations.
Check for studs at marked locations. If your
markings land on a stud, omit the drywall anchor
at that location for future steps.
Measure from the floor to your
initial desired height, marking
that height at each of your
marked vertical lines.
Center
Floor
Wall
Desired
Height
1.5”1.5”

Step 6: Drill Pilot Hole
Align Uprights. Place your upright upside-down.
Use the hole in the bottom of the upright to help
guide a provided screw. Gently drill in screw just
enough to mark the drywall.
Remove the Upright slat.
Verify the pilot hole.
Pilot Hole

Flip your upright with the slotted hole at the top (this is
the right-side-up). Attach Uprights to wall anchors using
provided screws.
TIP: Insert screw part way through the upright so the
screw tip pokes out to make alignment easier.
NOTE: Only drill into the top holes at this point.
NOTE: The
Upright will have
the slotted hole
at the top and
the keyholes will
be more narrow
in the front.
All three Uprights should look like this. The bottoms should swing somewhat freely.
Step 7: Drill Into Drywall
Drill the drywall anchor into the marked pilot hole.

Attach all headboard panels except the bottom one. Start from second lowest and work your way up.
Push the screw heads of the headboard panel into the slots on the upright and sliding down.
Use the provided level on the top headboard
panel. Shift the uprights until level.
C
A
D
B
Step 8: Place Headboard Panels
Step 9: Level

Step 10: Drill Lower Pilot Hole
Step 11: Drill Into Drywall
Screw in provided screws
through lower Upright
hole just enough to mark
the drywall.
Remove headboard panels by lifting
panel up and then pulling out. Start at
the top and work your way down.
Rotate Uprights out of the way. Drill the
drywall anchors into the pilot holes.
C
A
D
B

Screw in provided screws through
lower Upright holes.
Step 11: Drill Into Drywall (Continued)
Step 12: Attach Headboard Panels
Once the Uprights are properly
anchored to the wall, with the
appropriate distance between
them, begin attaching each
headboard panel from the
bottom up.
Attach First
Attach Last

Step 13: Relax
DONE!
Once all your Headboard Panels are attached,
jump into bed and and enjoy the weather!

Fabric Care Instructions
Cleaning Codes
Machine Washable
Spot Cleaning
SOLVENT OR WATER CLEANABLE (S/W)
WATER CLEANABLE (W)
SOLVENT CLEANABLE (S)
SPOT CLEAN ONLY (SC)
Spot clean with upholstery shampoo, foam from a mild detergent, or a mild dry cleaning solvent.
Spot clean fabric with a water-based shampoo or foam upholstery cleaner. Avoid over-wetting the stain.
Must be cleaned with solvents (dry clean only). Spot treat stains with a water-free solvent or
dry-cleaning product.
Cleaning depends on the nature of the stain. For oil-based spots, do not apply water and use dry
cloth. Recommended use of leather-specific solvents & cleaners.
Each fabric type has a specific cleaning code which can be found on the Free Swatch Page.
Many of our fabrics are machine washable. If a fabric is machine washable, it’ll be noted in the
cleaning instructions on the Free Swatch page. It must be Machine Wash - Cold. Use Cold Water
and a mild detergent on a low/gentle cycle. Hang dry all covers. Please note that every machine
wash adds wear to the fabric so it’s recommended to opt for spot cleaning prior to machine
washing whenever possible.
We recommend spot cleaning with either an upholstery shampoo, foam from a mild detergent, or
a mild cleaning solvent. Always hang to dry. When spills happen, blot immediately to remove the
spilled material. Clean spots or stains from the outside to the middle of the affected area (this prevents
circling). To prevent overall soiling, frequent vacuuming to remove dust and grime is recommended.