Inside Weather ELM STORAGE User manual

ELM STORAGE

Gather Your Eggs...
Top Shelf
Mid Shelf Divider Panel
Door
Hinge Screw Sticky Tab
Diffuser StripDoor Hinge
Side Panels
Small Shelf
Bottom Shelf
Back Panels
Top Lip
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
The parts shown here are all the available options. The parts you have will depend on your custom order.

Step 1: Attach Top to Right Side Panel
Make sure you use the correct shelf. The top shelf has longer center
channels than the others. Look for the series of dots communicating
which slot is for which shelf. One dot for the top shelf, Two dots for the
mid shelf and three dots for the bottom shelf.
Fastened Top and Side Panel
Place the top shelf face down on a
soft material to avoid scratching.
Top Shelf
Top Shelf
Mid Shelf
Right Side Panel
Left Side Panel One Dot
Two Dots
Three Dots
Connect the top shelf to the right side
panel using the installed fastners. You
may need to “pop” the shelf into the
side panel pocket.
Side Panel Pocket
Bottom Shelf

Step 2: Attach Mid and Bottom Shelf
Step 3: Attach Left Side Panel
Repeat Step 1 to attach the mid
and bottom shelves.
Attach left side panel using
the installed fasteners.
Bottom Shelf
Mid Shelf
Left Side Panel

Step 4: Inster Divider Panels
Slide the divider panels into the
divider slots.

Note: When fitting the peices together,
make sure the connecting screws are
retracted inside their housing. Having the
screw out could damage your surfaces.
Use the installed fasteners to
attach the back panel.
Step 5: Insert Back Panel
Insert the right back panel
into the slots flat. Slide it up
into the top slot.

Step 6: Insert Remaining Panels
Repeat Step 5 to install
the left panel
Next, side in any
center panels.
Attach with installed
fasteners.
NOTE: There is also a fastener on the
underside of the center panels that
needs to be tightened at this stage.

Step 7: Insert Remaining Panels
Step 8: Place Caps
Slide the top lip into place.
Use the installed fasteners to
attach the lip.
Place caps over all the
installed fasteners.

Step 9: Install Shelves (Optional)
Flip the unit upright.
If your unit has the optional
shelves, insert the shelf pins
and adjust shelves.
NOTE: Units that are 1 door wide will receive a standard small shelf. Units
that are 2 to 4 doors wide will receive small shelves with a notch. Use the
center notched shelf in the center alcove of your unit, and shelves with a
notch on the side on the outer alcoves
Small Shelf Small Shelf
(Center)
Small Shelf
(Side)

Step 10: Install Lighting (Optional)
Light Channel
Reciever Light Strip Cut Excess Strip
Install the lighting strip
(optional) before installing
the doors.
Use the light channels to
install the light strip.
Attach the reciever to the bottom
of the unit. Feed the light strip up
through the hole in the bottom
shelf on either end of the unit and
feed the strip through each cubby.
Peel back the paper from the
adhesive side of the light strip and
stick it to the inside of the light
channels.
Cut away any excess light strip.
Use diffuser strips to cover the light
channels.

Step 11: Install Doors
Place sticky tabs onto the
corners of the glass. These will
be under the door hinges.
Insert the door hinges
into the hinge holes.
Slide the door into the hinges.
Frosted glass will have the frosted side
on the inside.
Fluted glass will have the flutes on the
outside.
Tighten the hinge screws to attach the
glass. Make sure the edge of the glass
is flush to the back of the hinge.

Step 13: Install Remaining Doors
Step 12: Add Strike Plate
DONE!
Place the strike plate on the inside of the
door about .5” from the outer edge.